Summary of Contents for CommScope ERA CAP L2 18/21/ 23T/26 F-DC
Page 1
CommScope ERA ® CAP L2 with Fiber Interface Generation Low Power Carrier Access Point Installation Guide • M0203A9B_uc • September 2022...
Page 2
This document has been developed by CommScope, and is intended for the use of its customers and customer support ISCLAIMER personnel. The information in this document is subject to change without notice. While every effort has been made to eliminate errors, CommScope disclaims liability for any difficulties arising from the interpretation of the information contained herein.
"Hardware to Software Mapping Information” on page Document Revision History This is the second release of the CommScope ERA™ CAP L2 Second Generation Fiber Low Power Carrier Access Point Installation Guide. This release: adds the CAP L2 35LT/35HT and CAP L2 C-band models to...
Do not remove caps from any of the connectors until instructed to do so. The CAP L2 is to be used only with CommScope (NEC Class 2) or Limited Power Source ERA Subrack, or equivalent. Guard Against Damage from Electro-Static Discharge Electro-Static Discharge (ESD) can damage electronic components.
Page 10
1449. Suitability of the component for the application shall be determined for the intended installation. Notice: Corresponding local particularities and regulations must be observed. For national deviations, please refer to the respective documents, which are available from CommScope. Note: For a Class B digital device or peripheral: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.
Plenum Space 7809823-xx SFP+ Module Kits Contact your local CommScope sales representative to obtain the following components, as required, for this installation. Per the installation plan, obtain either Single Mode Fiber (SMF) or Multi Mode Fiber (MMF) that is of sufficient length to reach from the CAP L2 to a Classic CAN or TEN.
All CAP L2s include two OCTIS Universal Connector Kits (CommScope PN 7847069) for the interface to the Classic CAN or TEN that plugs into Port 1 and Port 2 on the CAP L2. CommScope provides the two OCTIS Kits for each CAP L2.
Unpack each container while carefully checking the contents for damage and verify with the packing slip. If damage is found or parts are missing, file a claim with the commercial carrier and notify CommScope Technical Support (see "CMS Global Technical Support”...
"Unpack and Inspect the CAP L2 and Optional Accessories” on page Wiring the AC/DC Power Supply Kit The CommScope Local AC Power Supply Kits are available in three configurations as shown in "CommScope Local AC/DC Power Supply Kits” on page 25.
Mounting a CAP L2 with a Hybrid Fiber Splice Box Kit (optional) The CAP L2 Hybrid Fiber Splice Box Kit (CommScope PN 7781091-xx) provides a connection solution for both power and optical signals to a CAP L2. For Fiber CAP L2s, you have the option to use composite cable to transport signals from a TEN or Classic CAN via fiber and power from a remote DC supply, and then use the CAP L2 Hybrid Fiber Splice Box Kit to terminate the power and fiber at the CAP L2.
The CAP L2 is equipped with an M6 grounding stud located on the back of the unit; however, grounding is not necessary. CAP L2s are classified as low-voltage devices and do not have internal power supplies. CommScope recommends checking your local and national electrical codes to determine if grounding is a requirement.
Calls to an EMEA Helpline outside of the 8:00 to 17:00 time frame will be forwarded to the 24x7 Helpline. Online Support To go to the CommScope Wireless Support Request web site from which you can initiate a Technical Support ticket, do one of the following: Scan the QR Code to the right.
DAS and Small Cell Customer Portal from the list of applications. • Scan the QR Code to the right to go directly to the CommScope DAS and Small Cell Customer Portal, where you can access the DAS and Small Cell user documentation.