Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for ESP BDeye
Summary of Contents for ESP BDeye
- Page 1 BDeye combined CCTV video door access system USER MAN UAL...
-
Page 3: Table Of Contents
Contents What is included and Optional Extras ........3 Description . -
Page 4: Description
Description MONITOR 2.5" HARD DISK CARTRIDGE VOICE ADJUSTMENT A/V OUT POWER SWITCH IR RECEIVER LOAD POWER TOUCH SPEAKER INDICATOR PANEL TCP/IP VDE CALL CAM 4 CAM 2 NETWORK POINT 1 SENSOR VDE CALL POWER DEVICE CAM 3 CAM 1 POINT 2 SUPPLY... - Page 5 INSERTION OF THE HARD DISK DRIVE 1. Follow the direction marked beside 2. Insert the hard disk paying attention the button to open the cover of the to the direction of the slot. hard disk cartridge. 3. Push the hard disk down. 4.
-
Page 6: Installation
2 – Control (Blue) 5 – Video In (Yellow) 3 – GND for Audio & Power (Brown) 4 – VDD (Red) 4-Pin connector for video door entry call point (BDeye VDE) 1 – GND (Black) 3 – B+ (Red) 2 – Video (Yellow) 4 –... -
Page 7: Operation
Operation HOW TO TURN ON 1. Push the power switch on the left side of the indoor unit, the monitor will start. 2. The monitor shows quad monitoring at start up as shown in Fig. 1 after system check. 3. If the time is within schedule recording time, the system will automatically start the schedule recording approximately 10 seconds after the boot up as shown in Fig. -
Page 8: Operation Buttons
Operation buttons ICON NAME OPERATION Display Full Screen Display of Channel 1/Number 1 Display Full Screen Display of Channel 2/Number 2 Display Full Screen Display of Channel 3/Number 3 Display Full Screen Display of Channel 4/Number 4 Display Quad Display Setup Enter/Exit Setup Audio Channel... -
Page 9: Setup
Setup To enter SETUP menu, press the stop button , then press The following screen will display: S S E E T T U U P P CAMERA ON/OFF CAMERA ON/OFF RECORD ON/OFF RECORD ON/OFF COVERT CHANNEL COVERT CHANNEL [ OFF ] [ OFF ] AUDIO PORT AUDIO PORT... - Page 10 COVERT FUNCTION CAMERA ON/OFF You can choose one channel to be covert. Frame rate of each channel can be set This covert channel will not be shown on separately to 1,2,3,4,5,6,12,16,25 FPS. the screen, but it can be recorded. Total frame rate of four channels is 50 FPS for PAL TV system and 60FPS for NTSC TV system.
- Page 11 VIDEO QUALITY MOTION DETECTION There are three options (HIGH, NORMAL RECORD TIME and LOW) for video quality of recording. Set the recording time when a motion event The better recording quality you choose, occurs in the SENSOR RECORDING mode. the more disk space it takes. Press button to select a preferred video DETECTED CHANNEL / AREA...
- Page 12 ALARM SETUP Press to move the red to the AREA, then press to select a channel and press to trigger the motion setting. VIDEO LOSS In the monitoring status,if the video cable connection is not good, the indoor unit will Four sensitivity levels can be selected and alarm with beep sound.
- Page 13 HARD DISK DRIVE GENERAL HDD information To set system-related issues. DATE/TIME: Set the system time. > ST9408221AS: Hard disk model. > HDD CAPACITY: The capacity of current hard disk. > HDD USED: The occupation of hard disk space, displayed in percentage. OVERWRITE ENABLED If it is set to YES, the system will automatically overwrites the earlier...
- Page 14 PASSWORD: Users can reset password. The length is fixed to 6 digits, stands for 1, stands for 2, stands for 3, stands for 4. The initial password is 111111 (press 6 times). Note: You can press to delete when you enter a wrong digit.
-
Page 15: Network
Network BASIC SETTING OF NETWORK Connect the monitor to the network. Press to enter the SETUP menu. Use button to select NETWORK, then press to enter the NETWORK menu. The screen will display as Fig. 33. N N E E T T W W O O R R K K MAC ADDRESS... - Page 16 SUBNET MASK DNS SERVER 1 Press to move to the digit to be Press to move to the digit to be set, then press to move to the set, then press to move to the corresponding digit and press to choose corresponding digit and press to choose it.
- Page 17 OPEN HTTP PORT Note: The port number can be omitted if you use the default port 80, for It's necessary to open the HTTP port of example http://192.168.18.101. the monitor before the users can get 2. After the plug-in installation, it will pop- remote access to it.
- Page 18 5. Click , input user ID and 6. Tools and control of the Remote Client password will appear at the bottom of the Remote Client window. Users can log in for further control. There are two types of users for remote access. One is administrator which has full operating rights and another is normal user which can view the monitored scene only.
- Page 19 DDNS setup 4. Enter http: //remoteview. dyndns - free. com: 6666 in your browser to get To setup Dynamic Domain Name Service. remote access to your monitor. The user is required to register and create a host name from the DDNS service provider WWW.DYNDNS.COM.
-
Page 20: Video Playback
Video Playback Users can press to select from different events, and press to play. In the event list, "T" stands for video clip PLAYBACK ON MONITOR recorded in always recording mode. "S" Press the stop recording key , then press stands for video clip recorded in sensor the play key , the system will... -
Page 21: Operation Instruction
Operation instruction MCG file dump Always Top Window 50% Screen 100% Screen 150% Screen Close Open another MCG file Jump back 60 Sec Jump back 10 Sec Switching storage device Preferences - Change the application's default setting Audio Output Setting / Volume control Move the window Drag the window by its part below title bar to move it... -
Page 22: Technical Specification
Technical Specification SYSTEM Control system LINUX System resources Triplex , supports simultaneous recording, video playback and network operations Operation interface User-friendly menu interface User interface Panel touch button and remote control Video protocol MPEG4 Audio protocol ADPCM2 VIDEO Video input 4 x camera plus 2 x video door entry Video output One way... - Page 23 POWER SUPPLY Video call point Four way camera powered by integral central power supply Outdoor station Two way outdoor station powered by integral central power supply SPECIFICATIONS Power supply DC +12V 4.5A Screen 8” TFT-LCD Resolution 800x600 Temperature Range -10ºc – +70ºc Dimensions 250 ×...
- Page 24 Technical Support 01527 515145 Elite Security Products Telephone: 01527 515150 Unit 7, Target Park, Shawbank Rd Technical Support: 01527 515145 Lakeside, Redditch B98 8YN email: info@espuk.com...
Need help?
Do you have a question about the BDeye and is the answer not in the manual?
Questions and answers