Table of Contents
Advertisement
Quick Links
Model No. : UT-1407
(TEMP., HUMIDITY, P AND TIME INDICATOR)
Sure for service with hi-end
Sure for service with hi-end
Add.-78/1/Z/3, Makarpura GIDC, Makarpura, Vadodara
Sales:
+91 94273 01436
z
OPERATION MANUAL
CLEAN ROOM INDICATOR
Δ
Model No. : UT-1407
Website:
www.utplindia.in
Uni
Uni
versal
versal
Tech
Tech
nology
nology
Ph
:
+91 7046223333
z
E-mail :
sales@utplindia.in
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Unitech UT-1407
Summary of Contents for Unitech UT-1407
- Page 1 Model No. : UT-1407 OPERATION MANUAL CLEAN ROOM INDICATOR (TEMP., HUMIDITY, P AND TIME INDICATOR) Δ Model No. : UT-1407 Sure for service with hi-end Sure for service with hi-end versal versal Tech Tech nology nology Add.-78/1/Z/3, Makarpura GIDC, Makarpura, Vadodara...
- Page 2 ERROR MESSAGE AND TROUBLESHOOTING COMMUNICATION PROTOCOL INTRODUCTION Unitech Instrument’s Clean Room Indicator is designed to display Temperature, Humidity and Room Pressure Difference in one unit. These instrument accepts inputs from standard T + RH sensor or internal sensor. The instrument displays the temperature (ºC) in the range of 0 to 100ºC and humidity in the range of 0.0 to 100.0 % RH...
-
Page 3: Front Panel Description
Model No. : UT-1407 PAGE : 2 FRONT PANEL DESCRIPTION 1010 ºC High KEY PAD High COM. High MODEL NO: UT-1407 NO DISPLAY DESCRIPTION Seven Segment LED displays of T RH DP & TIME Red LED will glow on low Process values of ºC,%Rh, or P Δ... -
Page 4: Technical Specification
Model No. : UT-1407 PAGE : 3 TECHNICAL SPECIFICATION FDA 21 CFR part 11 - GAMP-4 compatible. Microcontroller based indicator with inbuilt Temperature, RH & DP measurement in single enclosure. All channel are programmable ranges and unit.(Through Front key pad). -
Page 5: Installation
Model No. : UT-1407 PAGE : 4 INSTALLATION Terminal Detail T + rH SENSOR RS-485 24VDC CAUTION WIRING CONSIDERATION SHIELDED TWISTED PAIR WIRE IS USED FOR ALL ANALOG I/P, PROCESS SENSORS, RTD, THERMOCOUPLE, DC mV-mA, VOLT DC, LINEAR INPUT AND COMMUNICATION... -
Page 6: Programming Flow Chart
Model No. : UT-1407 PAGE : 5 PROGRAMMING FLOW CHART Configuration Setup Change Mode Calibration Selection Mode Mode Mode Password Press Press Press Press Press new - Sure for service with hi-end Sure for service with hi-end versal versal Tech... -
Page 7: Configuration Mode
Model No. : UT-1407 PAGE : 6 CONFIGURATION MODE CONFIGURATION MODE PARAMETER Description Range Parameter Default Value Password for Parameter Setting Scroll the digit by key, increase by 000 to 999 Values between Password for Configuration Parameter Temperature Alarm-1 type... - Page 8 Model No. : UT-1407 PAGE : 7 Description Range Parameter Default Value RH Damping Change the value by key or key. 00 to 10 Values between Note: Factory set Value Pressure Damping Change the value by key or key. 00 to 10...
-
Page 9: Setup Mode
Model No. : UT-1407 PAGE : 8 SETUP MODE Range Description Parameter Default Value Password for Parameter Setting Scroll the digit by key, increase by 000 to 999 Values between Password for Configuration Parameter Temperature Alarm 1 Set point Scroll the digit by... -
Page 10: Calibration Mode
Model No. : UT-1407 PAGE : 9 CALIBRATION MODE CALIBRATION MODE PASSWORD PROTECTED MODE Description Range Parameter Default Value Password for Parameter Setting Scroll the digit by key, increase by 000 to 999 Values between Password for Configuration Parameter Pressure Low Calibration Apply Press. - Page 11 Model No. : UT-1407 PAGE : 10 REGISTER ADDRESS FOR MODBUS RTU PROTOCOL SR NO PARAMETERS ABSOLUTE ADDRESS ACCESS TYPE TEMPERATURE VALUE 40001 READ ONLY HUMIDITY VALUE 40002 READ ONLY DIFF. PRESS. VALUE 40003 READ ONLY SETPOINT 1 LOW 40004...
Need help?
Do you have a question about the UT-1407 and is the answer not in the manual?
Questions and answers