Table of Contents
Advertisement
Input search
When a signal is not detected, another input with a
signal is automatically selected.
Note
●
MEMORY VIEWER input is not a subject of the "no
signal" detection. It is excluded from this function.
Select the item with
Select the set point with
Input search
Input search
Custom
1st search input
2nd search input
[Input search]
[Off]:
When there is no signal, the input is not switched
automatically.
[All inputs]:
Searches all inputs and switches to an input with
a signal.
Input search is executed in the following order.
(Example) When the current input is [HDMI1]
[HDMI2] → [DIGITAL LINK] → [DVI-D] → [PC] →
[VIDEO] → [USB] → [HDMI1]
Note
●
The inputs set to [(Skip)] in [Input label] (see
page 51) are skipped when searching.
[Custom]:
Repeatedly searches [Current input], [1st search
input] and [2nd search input] in order, and switches
to an input with a signal.
[Input detection]:
Monitors the following inputs set to [On], detects
the status change from no signal to signal present,
and switches to the input.
[HDMI1], [HDMI2], [DIGITAL LINK], [DVI-D], [PC]
PC
16:9
Searching...
[Searching...] is displayed during the input search.
[1st search input], [2nd search input]
Set the input to search when [Custom] is selected.
[HDMI1] / [HDMI2] / [DIGITAL LINK] / [DVI-D] /
[PC] / [VIDEO] / [USB] / (None)
[Detect digital input]
Sets the digital input to monitor during [Input detection].
[HDMI1] / [HDMI2] / [DIGITAL LINK] / [DVI-D]
.
.
(None)
(None)
[Changing delay]
Sets the delay time until the input is switched during
[Input detection].
[Off]:
Switches the input if a signal is interrupted even for
a very short period.
1 to 10:
Sets the delay time (sec.).
Switches the input when the set time has elapsed
after detecting no signal is present.
However, if the detection period during which no
signal is present is shorter than the set delay time,
the input is not switched.
Note
●
When set to the USB input, the unit determines
no signal is present if the USB memory is not
connected to the USB terminal.
In addition, even when a USB memory is
connected, if there is no playable file, the unit
determines no signal is present.
●
This menu will be greyed out and cannot be set
under the following conditions.
[Input lock] is not set to [Off]. (see page 73)
•
When [Setup] - [Image settings] - [No signal
•
image settings] - [Display setting] is set to [On].
(see page 55)
●
If the input is changed by this function, the last
input is selected when the power is turned on next
time.
If you wish to retain the original input when the
power is turned on, set [Initial input] to the original
input. (see page 73)
●
[Input detection] is the function that automatically
switches the input as below by monitoring the
presence of signal for the set input.
If a video signal is input to the set input that is
•
not displayed (When the status has changed
from signal absent to signal present.), the input
is selected and switched.
If no signal is detected for the displayed input,
•
the setting switches to the set input to which a
signal is input. Also, if no signal is present for
the displayed input when the power is turned
on or when the input is switched, the setting
switches to the set input to which a signal is
input. When signals are input to multiple set
inputs, the priority order as default (immediately
after power-on) is as follows: [HDMI1], [HDMI2],
[DIGITAL LINK], [DVI-D], [PC]
In the other case (When the input is switched
after power-on), the input displayed last takes
priority.
69
English
Advertisement
Table of Contents
