Advertisement
Declaration of Conformity
CE Conformity Statement
Radio products with the CE alert marking comply with
the RED Directive (2014/53/EU) issued by the
Commission of the European Community. Compliance
with this directive implies conformity to the following
European Norms (in brackets are the equivalent
international standards).
• EN 300 328 Technical requirement for radio
equipment
• ET S301 489 General EMC requirements for radio
equipment
Products that contain the radio transmitter are labeled
with CE alert marking and may also carry the CE logo.
FCC Compliance Statement
This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful
interference to radio communications. However, there
is no guarantee that interference will not occur in a
particular installation. If this equipment does cause
harmful interference to radio or television reception,
which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the
interference by one of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and
receiver.
• Connect the equipment into an outlet on a circuit
different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV
technician for help.
To assure continued compliance, any changes or
modifications not expressly approved by the party
responsible for compliance could void the user's
authority to operate this equipment. (Example: use only
shielded interface cables when connecting to computer
or peripheral devices).
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
1)
This device may not cause harmful interference,
and
2)
This device must accept any interference
received, including interference that may cause
undesired operation.
15.21
Any changes or modifications not expressly approved by
the party responsible for compliance could void the
authority to operate equipment.
This device and its antenna must not be co-located or
operating in conjunction with any other antenna or
transmitter.
End-users and installers must be provided with antenna
installation instructions and transmitter operating
conditions for satisfying RF exposure compliance.
For product available in the USA/Canada market, only
channel 1~11 can be operated. Selection of other
channels is not possible.
FCC Radiation Exposure Statement
This equipment complies with FCC RF radiation
exposure limits set forth for an uncontrolled
environment for body-worn configuration in direct
contact to the phantom.
This device complies with FCC radiation exposure limits
set forth for an uncontrolled environment.
This equipment complies with FCC radiation exposure
limits set forth for an uncontrolled environment. End
user must follow the specific operating instructions for
satisfying RF exposure compliance. This transmitter
must not be co-located or operating in conjunction with
any other antenna or transmitter.
The portable device is designed to meet the
requirements for
exposure to radio waves established by the Federal
Communications
Commission (USA). These requirements set a SAR limit
of 1.6 W/kg
averaged over one gram of tissue. The highest SAR value
reported under
this standard during product certification for use when
properly worn on the body
IC warning statement
This device complies with Industry Canada's licence-exempt
RSSs. Operation is subject to the following two conditions:
(1) This device may not cause interference; and (2) This
device must accept any interference, including interference
that may cause undesired operation of the device.
Le présent appareil est conforme aux CNR d'Industrie Canada
applicables aux appareils radio exempts de licence.
L'exploitation est autorisée aux deux conditions suivantes : (1)
l'appareil ne doit pas produire de brouillage, et (2)
l'utilisateur de l'appareil doit accepter tout brouillage
radioélectrique subi, même si le brouillage est susceptible
d'en compromettre le fonctionnement.
This radio transmitter has been approved by Industry Canada
to operate with the
antenna types listed below with the maximum permissible
gain and required
antenna impedance are strictly prohibited for use with this
device.
Le present emetteur radio a ete approuve par Industrie
Canada pour fonctionner
avec les types d'antenne enumeres ci-dessous et ayant un
gain admissible maximal
et l'impedance requise pour chaque type d'antenne. Les
types d'antenne non inclus
dans cette liste, ou dont le gain est superieur au gain maximal
indique, sont
strictement interdits pour l'exploitation de l'emetteur.
(i)the device for operation in the band 5150–5250 MHz is
only for indoor use to reduce the potential for harmful
interference to co-channel mobile satellite systems;
(For devices installed in vehicles point i. is not
required.)
Users should also be advised that high-power radars are
Advertisement
