Advantech MIC-1810 Startup Manual

Intel core i3-3217ue/celeron 1047ue embedded automation computer
Hide thumbs Also See for MIC-1810:

Advertisement

Quick Links

MIC-1810
Intel
Core™ i3-3217UE/Celeron
®
Embedded Automation Computer
Startup Manual
Packing List
Before you begin installing your card, please make sure
that the following items have been shipped:
1. 1 x MIC-1810 system
2. 1 x Adapter 100 ~ 240 V 60W 12 V WO/PFC
DC plug 90°
3. 1 x MIC-1810 startup manual
4. 1 x User note for MIC-1810
If any of these items are missing or damaged, please con-
tact your distributor or sales representative immediately.
Caution: BATTERIES ARE AT RISK OF EXPLODING IF
INCORRECTLY REPLACED. REPLACE ONLY WITH
THE SAME OR EQUIVALENT TYPE RECOMMEND-
ED BY THE MANUFACTURER. DISCARD USED
BATTERIES ACCORDING TO THE MANUFAC-
TURER'S INSTRUCTIONS.
Attention: DANGER D'EXPLOSION SI LA BATTERIE EST
INEXACTEMENT REMPLACÉE. REMPLACEZ
SEULEMENT AVEC LA MÊME CHOSE OU LE TYPE
ÉQUIVALENT RECOMMANDÉ PAR LE FABRICANT,
JETTENT LES BATTERIES UTILISÉES INSTRUC-
TIONS DE S SELON FABRICANT DES'.
For more information about this or other Advantech
products, please visit our website at
http://www.advantech.com
http://www.advantech.com/Products
For technical support and service, please visit our
support website at
http://support.advantech.com.tw/support/default.
aspx
This manual is for the MIC-1810 Series Rev. A1.
Part No. 2001181001
Printed in Taiwan
Edition 2
September 2017
1047UE
®
Specifications
System
• 3rd generation Intel
Core™ i processer with QM77 chipset
®
Memory
• 4G SODIMM DDR3-1600 204 pin 512MX8 1.35 V
Graphics
• Intel
HD Graphics 4000, supports DirectX11
®
Serial Ports
• 2 x RS-232 via COM1/COM2
Ethernet
• Interface: 10/100/1000 Mbps
• Controller
LAN1: QM77 (MAC) + 82579LM GbE (PHY)
LAN2: 82583V Gigabit Ethernet controller
Storage
• Internal SSD Bay: 1 x 2.5" SSD bay
Front I/O
• Display: 1 x VGA/HDMI
• USB: 2 x USB 3.0, 2 x USB 2.0

Power Requirement

• Power Type: DC power jack
• Input Voltage: 12 V
DC
Miscellaneous
• Power Switch
Orange: System standby
Green: System boot
Table Mount (Optional)
• P/N: 1960077844N001
• Dimensions (W x L): 130 x 175 mm
Environment
• Operating Temperature: 0 ~ 50 °C with 0.7m/S air flow
and 1 x industrial SSD
• Relative Humidity: 95% @ 40 °C (non-condensing)
Physical Characteristics
• Dimensions (W x H x D): 165 x 130 x 59 mm
• Weight: 1.45 kg (3.19 lb)
MIC-1810 Startup Manual 1

Advertisement

Table of Contents
loading

Summary of Contents for Advantech MIC-1810

  • Page 1: Power Requirement

    • Dimensions (W x H x D): 165 x 130 x 59 mm http://support.advantech.com.tw/support/default. • Weight: 1.45 kg (3.19 lb) aspx This manual is for the MIC-1810 Series Rev. A1. Part No. 2001181001 Edition 2 September 2017 Printed in Taiwan...
  • Page 2: Analog Input

    DAQ Specifications DAQ Specifications (Cont.) The MIC-1810 system features a built-in data acquisition Analog Output module (MIOe-3810). Channels Analog Input Resolution 12 bits Channels 16 single ended/8 differential Memory Size 4K samples Resolution 12 bits Update Rate 500 KS/s Built-In...
  • Page 3: Installation Procedures

    DAQ Specifications (Cont.) Installation Procedures (Cont.) Counter Table Mount Installation MIC-1810 can be integrated with a table mount for easy Counter chip operation. To prevent the system from overheating, the side of the system with the heat sink must be facing upward.
  • Page 4: System Dimensions

    System I/O Interface System Dimensions 4 MIC-1810 Startup Manual...
  • Page 5 快速入门手册 包装清单 产品规格 处理器系统 安装板卡之前,用户需确认包装中含有本设备以及下面所 列各项: • Intel第三代Core i处理器,带QM77芯片组 1. 1 x MIC-1810系统 x 1 内存 2. 1 x 适配器100 240 V 60W 12 V WO/PFC DC plug 90° • 4G SODIMM DDR3-1600 204针512MX8 1.35 V 3. 1 x MIC-1810快速入门手册...
  • Page 6 ± 输出电压 偏移误差:可调至0 高 2 V min.@ -15mA(拉电流) 增益 输入负载 10KΩ上拉电阻,连接至 5V 增益误 精度 差 (%FSR) 通道类 单端/差分 型 SNR:68 dB ENOB:10.5 bits 低:最大0.8V; 外部数字量 高:最小2.0V 触发 最小脉冲宽度:50 ns 范围:-10 ~ 10V 外部模拟量 触发 分辨率:12 bits (4.88 mV/step) 2 MIC-1810快速入门手册...
  • Page 7 最大0.8 V @+15mA 计数器输出 高 最小2.0 V @-15mA 频率测量 0.1%,输入信号频率 ≥ 40KHz 脉冲宽度测量 0.1%,输入信号频率 ≤ 40KHz 高级功能误差 脉冲输出 小于2%,输出频率 > 1MHz PWM输出 小于2%,输出频率> 1MHz 简易安装指导 HDD安装 1. 卸下4颗螺丝后移除底盖。 2. 从底盖上卸下用于固定SSD的4颗螺丝。 3. 插接SATA线缆/电源线后放回后盖并用4颗螺丝固定。 符合性声明 本品符合FCC规则第15款限制。操作符合下列两种情况: 1. 此设备不可产生干扰, 2. 本设备必须接受任何收到的干扰,但干扰可能导致意外 操作。 MIC-1810快速入门手册 3...
  • Page 8 系统I/O接口 系统尺寸 4 MIC-1810快速入门手册...

Table of Contents