Download Print this page
Front Runner KSTF003T Quick Start Manual

Front Runner KSTF003T Quick Start Manual

Toyota 4runner (2010 - current) slimsport roof rack kit

Advertisement

Quick Links

front runner
START HERE!
Don't be a hero and muscle through this installation without reading these fitting instructions first! Improper installation of this gear may void certain
aspects of your warranty.
Before you begin, take a moment and open all your Front Runner rack kit boxes and gather the assembly instructions for the various components.
A complete kit will contain:
1. A Front Runner Mounting system specific to your vehicle
2. A Front Runner Rack Tray or Load bar Slats
This document will guide you through the assembly of the mounting system and assist you in fitting the roof rack tray or load bars to your specific
vehicle.
Please refer to the next page for a list of all the components, quantities and tools required.
IT IS CRITICAL THAT ALL FRONT RUNNER PRODUCTS BE PROPERLY AND SECURELY ASSEMBLED AND ATTACHED TO YOUR VEHICLE. IMPROPER ATTACHMENT COULD
RESULT IN AN AUTOMOBILE ACCIDENT, AND COULD CAUSE SERIOUS BODILY INJURY OR DEATH. YOU ARE RESPONSIBLE FOR ASSEMBLING AND SECURING ALL FRONT
RUNNER PRODUCTS TO YOUR VEHICLE, CHECKING THE ATTACHMENTS PRIOR TO USE, AND PERIODICALLY INSPECTING THE PRODUCTS FOR ADJUSTMENT, WEAR AND
DAMAGE. THEREFORE, YOU MUST READ AND UNDERSTAND ALL OF THE INSTRUCTIONS AND PRECAUTIONS SUPPLIED WITH YOUR FRONT RUNNER PRODUCT PRIOR TO
INSTALLATION OR USE. IF YOU DO NOT UNDERSTAND ALL OF THE INSTRUCTIONS AND CAUTIONS, OR IF YOU HAVE NO MECHANICAL EXPERIENCE AND ARE NOT THOROUGHLY
FAMILIAR WITH THE INSTALLATION PROCEDURES, YOU SHOULD HAVE THE PRODUCT INSTALLED BY A PROFESSIONAL INSTALLER OR OTHER QUALIFIED PERSONNEL.
NOTE: Front Runner will not be responsible for any damage caused by the failure to install the product according to these instructions.
KSTF001_REV_A04
TOYOTA 4runner (2010 - CURRENT)
SLIMSPORT ROOF RACK KIT
READ ME FIRST
IMPORTANT WARNING!
Please call us if you have any questions about the installation of this product.
1
KSTF001
© 2022 FRONT RUNNER VEHICLE OUTFITTERS
ENG

Advertisement

loading

Summary of Contents for Front Runner KSTF003T

  • Page 1 Don’t be a hero and muscle through this installation without reading these fitting instructions first! Improper installation of this gear may void certain aspects of your warranty. Before you begin, take a moment and open all your Front Runner rack kit boxes and gather the assembly instructions for the various components. A complete kit will contain: 1.
  • Page 2 10mm Plastic Spacer 13mm Anti Seize / Oil Driver 10mm M8 x 19 x 12 Flat Washer M8 Spring Washer M6 x 12 x 1 Flat Washer Torx Insulation Sealant Marker 12mm Tape FIGURE 1.1 KSTF001_REV_A04 © 2022 FRONT RUNNER VEHICLE OUTFITTERS...
  • Page 3 With the factory rails removed and starting at the front edge of the molding, measure and mark the dimensions as shown onto both the LH & RH ditch moldings. 445mm 370mm Remove Remove KSTF001_REV_A04 © 2022 FRONT RUNNER VEHICLE OUTFITTERS...
  • Page 4 4mm Allen Key Bit, set the Jack Nut into the hole while holding onto the handle of the Installer Wrench. Make sure that the Jack Nut has pulled up all the wat to the inside skin of the roof panel. KSTF001_REV_A04 © 2022 FRONT RUNNER VEHICLE OUTFITTERS...
  • Page 5 Fasten the front foot by inserting the fastener (item 17) through the double sided tape and securing into the Jack Nut fitted earlier. Fully tighten all fasteners. Place M6 and M8 Nut Caps over all hex Bolts. KSTF001_REV_A04 © 2022 FRONT RUNNER VEHICLE OUTFITTERS...
  • Page 6 LH & RH ditch moldings. 445mm 370mm Remove Remove Use denatured alchohol and ensure the ditch is clean from any residue where the Support Plate 01 (Item 3) will be resting on the ditch. KSTF001_REV_A04 © 2022 FRONT RUNNER VEHICLE OUTFITTERS...
  • Page 7 19 x 2 Flat Washers, M8 Spring Washers and M8 x 60 Hex Bolts (Item 18, 13 & 14). Fully tighten all fasteners. Place M6 and M8 Nut Caps over all hex Bolts. KSTF001_REV_A04 © 2022 FRONT RUNNER VEHICLE OUTFITTERS...
  • Page 8 FIT AND SECURE STANDARD WIND FAIRING ASSEMBLY Refer to fitment guide RRAC234 10mm LIGHT BAR WIND FAIRING ASSEMBLY Refer to fitment guide RRAC195 KSTF001_REV_A04 © 2022 FRONT RUNNER VEHICLE OUTFITTERS...
  • Page 9 IMPORTANT! FRONT RUNNER RACK KITS OFTEN HAVE A HIGHER LOAD RATING THAN THE VEHICLES THEY ARE MOUNTED TO. PLEASE REFER TO YOUR SPECIFIC VEHICLE MANUFACTURER FOR A RECOMMENDED ROOF RATING. FRONT RUNNER CANNOT BE RESPONSIBLE FOR IMPROPER LOADING BEYOND THE VEHICLE MANUFACTURER'S STATED LOAD CAPACITY.

This manual is also suitable for:

Kstf002t