Front Runner SSDS602 Fitting Instructions Manual

Front Runner SSDS602 Fitting Instructions Manual

Mitsubishi triton (l200) deck completion set

Advertisement

Before you start, take a moment to familiarize yourself with the Fitting Instructions and the components received.
IT IS CRITICAL THAT ALL FRONT RUNNER PRODUCTS BE PROPERLY AND SECURELY ASSEMBLED AND ATTACHED TO YOUR VEHICLE. IMPROPER ATTACHMENT COULD
RESULT IN AN AUTOMOBILE ACCIDENT, AND COULD CAUSE SERIOUS BODILY INJURY OR DEATH. YOU ARE RESPONSIBLE FOR ASSEMBLING AND SECURING ALL FRONT
RUNNER PRODUCTS TO YOUR VEHICLE. CHECKING THE ATTACHMENTS PRIOR TO USE, AND PERIODICALLY INSPECTING THE PRODUCTS FOR ADJUSTMENT, WEAR AND
DAMAGE. THEREFORE YOU MUST READ AND UNDERSTAND ALL OF THE INSTRUCTIONS AND PRECAUTIONS SUPPLIED WITH YOUR FRONT RUNNER PRODUCT PRIOR TO
INSTALLATION OR USE. IF YOU DO NOT UNDERSTAND ALL OF THE INSTRUCTIONS AND CAUTIONS, OR IF YOU HAVE NO MECHANICAL EXPERIENCE AND ARE NOT THOROUGHLY
FAMILIAR WITH THE INSTALLATION PROCEDURES, YOU SHOULD HAVE THE PRODUCT INSTALLED BY A PROFESSIONAL INSTALLER OR OTHER QUALIFIED PERSONNEL.
SSDS602_REV_A00
Mitsubishi Triton (L200)
Deck Completion Set
READ ME !
Thank you for purchasing a Front Runner Deck Completion Set.
Refer to Page 2 for a list of all the components, quantities and tools required.
IMPORTANT WARNING!
1
© COPYRIGHT 2016 FRONT RUNNER VEHICLE OUTFITTERS
ENG
SSDS602
45 min

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the SSDS602 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for Front Runner SSDS602

  • Page 1 IMPORTANT WARNING! IT IS CRITICAL THAT ALL FRONT RUNNER PRODUCTS BE PROPERLY AND SECURELY ASSEMBLED AND ATTACHED TO YOUR VEHICLE. IMPROPER ATTACHMENT COULD RESULT IN AN AUTOMOBILE ACCIDENT, AND COULD CAUSE SERIOUS BODILY INJURY OR DEATH. YOU ARE RESPONSIBLE FOR ASSEMBLING AND SECURING ALL FRONT RUNNER PRODUCTS TO YOUR VEHICLE.
  • Page 2 M6 x 12 x 1SS Flat Washer M6 Nyloc Nut 60mm Carabiner 6.5MM M6 Cage Nut Rear Corner Wing Bracket RH Rear Corner Wing Bracket LH Finishing Washer M6 x 30 Countersink Screw FIGURE 1.1 SSDS602_REV_A00 © COPYRIGHT 2016 FRONT RUNNER VEHICLE OUTFITTERS...
  • Page 3 65mm from the rear of the loadbed. 6.5MM Before you start to fit the wing brackets to the Drawer, clip the M6 Cage Nuts (Item 11) into the Rear Corner Wings (Item 12 & 13) supplied with SSDS602. SSDS602_REV_A00...
  • Page 4 Repeat this on the other rear corner of the Drawer System. Position First Position Second The rear support bracket is also part of SSWS001. Fit and secure with the fasteners supplied with SSWS001 as shown. 10MM SSDS602_REV_A00 © COPYRIGHT 2016 FRONT RUNNER VEHICLE OUTFITTERS...
  • Page 5 M6 x 12 button Heads, M6 x 12 x 1SS Flat Washers and M6 Nyloc Nuts (Item 7, 8 & 9) as shown. Repeat this on the other side of the drawer. © COPYRIGHT 2016 FRONT RUNNER VEHICLE OUTFITTERS SSDS602_REV_A00...
  • Page 6 Finishing Washers (Items 14 & 15) as shown. 2.11 Fit the Side Decks (Items 1 & 4) to the Drawer by sliding it into the C-Clips. 2.12 Position of all four Decks. © COPYRIGHT 2016 FRONT RUNNER VEHICLE OUTFITTERS SSDS602_REV_A00...
  • Page 7 Congratulations! You did it. Take a step back and admire your work! Front Runner will not be responsible for any damage caused by the failure to install the product according to these instructions. Please call us if you have any questions about the installation of this product.

Table of Contents