Download Print this page
Front Runner KSTL001 Manual

Front Runner KSTL001 Manual

Toyota land cruiser 100 slimsport tray

Advertisement

Quick Links

front runner
START HERE!
Don't be a hero and muscle through this installation without reading these fitting instructions first! Improper installation of this gear may void certain
aspects of your warranty.
Before you begin, take a moment and open all your Front Runner rack kit boxes and gather the assembly instructions for the various components.
A complete kit will contain:
1. A Front Runner Mounting system specific to your vehicle
2. A Front Runner Rack Tray or Load bar Slats
This document will guide you through the assembly of the mounting system and assist you in fitting the roof rack tray or load bars to your specific
vehicle.
Please refer to the next page for a list of all the components, quantities and tools required.
IT IS CRITICAL THAT ALL FRONT RUNNER PRODUCTS BE PROPERLY AND SECURELY ASSEMBLED AND ATTACHED TO YOUR VEHICLE. IMPROPER ATTACHMENT COULD
RESULT IN AN AUTOMOBILE ACCIDENT, AND COULD CAUSE SERIOUS BODILY INJURY OR DEATH. YOU ARE RESPONSIBLE FOR ASSEMBLING AND SECURING ALL FRONT
RUNNER PRODUCTS TO YOUR VEHICLE, CHECKING THE ATTACHMENTS PRIOR TO USE, AND PERIODICALLY INSPECTING THE PRODUCTS FOR ADJUSTMENT, WEAR AND
DAMAGE. THEREFORE, YOU MUST READ AND UNDERSTAND ALL OF THE INSTRUCTIONS AND PRECAUTIONS SUPPLIED WITH YOUR FRONT RUNNER PRODUCT PRIOR TO
INSTALLATION OR USE. IF YOU DO NOT UNDERSTAND ALL OF THE INSTRUCTIONS AND CAUTIONS, OR IF YOU HAVE NO MECHANICAL EXPERIENCE AND ARE NOT THOROUGHLY
FAMILIAR WITH THE INSTALLATION PROCEDURES, YOU SHOULD HAVE THE PRODUCT INSTALLED BY A PROFESSIONAL INSTALLER OR OTHER QUALIFIED PERSONNEL.
NOTE: Front Runner will not be responsible for any damage caused by the failure to install the product according to these instructions.
KSTL001_REV_A00
TOYOTA land cruiser 100
SLIMSPORT tray
READ ME FIRST
IMPORTANT WARNING!
Please call us if you have any questions about the installation of this product.
1
KSTL001
© 2023 FRONT RUNNER VEHICLE OUTFITTERS
ENG

Advertisement

loading
Need help?

Need help?

Do you have a question about the KSTL001 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for Front Runner KSTL001

  • Page 1 Don’t be a hero and muscle through this installation without reading these fitting instructions first! Improper installation of this gear may void certain aspects of your warranty. Before you begin, take a moment and open all your Front Runner rack kit boxes and gather the assembly instructions for the various components. A complete kit will contain: 1.
  • Page 2 M6 x 25 Tread Forming Screw 11 X Slat Joiner Plate 18 X M6 Nyloc Nut 18 X M6 Nut Cap 18 X 19 x 22 Spacer FIGURE 1.1 Detail A Front Detail A KSTL001_REV_A00 © 2023 FRONT RUNNER VEHICLE OUTFITTERS...
  • Page 3 Tightening Torque 8-10Nm / 5.9 ft lb - 7.38 ft lb. Take care when using a cordless driver. FIT AND SECURE Remove Ditch Trim on both sides. Clean thoroughly around each mounting hole. Denatured Alcohol KSTL001_REV_A00 © 2023 FRONT RUNNER VEHICLE OUTFITTERS...
  • Page 4 2 Flat Washers and M8 x 50 Hex Bolts. (Items 5 & 6). Fully tighten all fasteners. Place M8 Nut Caps (Item 7) over all Hex Bolts. Tightening Torque: M8 : 15-20Nm / 11.06 ft lb - 14.75 ft lb KSTL001_REV_A00 © 2023 FRONT RUNNER VEHICLE OUTFITTERS...
  • Page 5 FIT AND SECURE STANDARD WIND FAIRING ASSEMBLY Refer to fitment guide RRAC281 10mm LIGHT BAR WIND FAIRING ASSEMBLY Refer to fitment guide RRAC282 KSTFL01_REV_A00 © 2023 FRONT RUNNER VEHICLE OUTFITTERS...
  • Page 6 IMPORTANT! FRONT RUNNER RACK KITS OFTEN HAVE A HIGHER LOAD RATING THAN THE VEHICLES THEY ARE MOUNTED TO. PLEASE REFER TO YOUR SPECIFIC VEHICLE MANUFACTURER FOR A RECOMMENDED ROOF RATING. FRONT RUNNER CANNOT BE RESPONSIBLE FOR IMPROPER LOADING BEYOND THE VEHICLE MANUFACTURER'S STATED LOAD CAPACITY.

This manual is also suitable for:

Kstl002t