Table of Contents
Advertisement
N
Notes on the instruction manual ............................................ 8
O
On/Off request ..................................................................... 90
Operating mode ................................................................... 81
Operating the room temperature controller.......................... 29
Operation ....................................................................... 11, 25
Outside temperature for summer compensation ................. 88
P
Presence detector ............................................................... 83
Priority ............................................................................... 105
Q
Qualification of personnel .................................................... 11
R
Request fan speed level ...................................................... 91
Request fan speed level manual ......................................... 91
Request setpoint .................................................................. 90
Requirements for the electrician .......................................... 18
Resetting manual setpoints ................................................. 87
Rocker switch function ......................................................... 29
S
Safety .................................................................................... 9
Safety instructions ............................................................... 12
Selecting the application program ....................................... 24
Send cyclic "In operation" (min) ........................................... 37
Setpoint adjustment ............................................................. 62
Setpoint adjustment - Maximum manual increase during
cooling mode (0 - 15°C) ................................................. 63
Setpoint adjustment - Maximum manual increase during
heating mode (0 - 15°C) ................................................. 62
Setpoint adjustment - Maximum manual reduction during
cooling mode (0 - 15°C) ................................................. 63
Setpoint adjustment - Maximum manual reduction during
heating mode (0 - 15°C) ................................................. 62
Setpoint adjustment - Permanent storage of on-site operation
........................................................................................ 64
Setpoint adjustment - Resetting of the manual adjustment for
receipt of a basic setpoint ............................................... 63
Setpoint adjustment - Resetting the manual adjustment for
change of operating mode .............................................. 64
Setpoint adjustment - Resetting the manual adjustment via
object .............................................................................. 64
Setpoint display ................................................................... 90
Setpoint reached ................................................................. 89
Setpoint settings .................................................................. 58
Setpoint settings - Cyclic sending of the current set-point
temperature (min) ........................................................... 62
Setpoint settings - Display indicates .................................... 61
Setpoint settings - Hysteresis for switchover heating/cooling
........................................................................................ 59
Setpoint settings - Increase for ECO cooling (°C) ............... 61
Setpoint settings - Increase for standby cooling (°C) .......... 60
Setpoint settings - Reduction for ECO heating (°C) ............ 60
Setpoint settings - Reduction for standby heating (°C) ....... 59
Setpoint settings - Send current setpoint ............................. 62
200-00547-A 06-26-2018 LW
Description of application and parameters
Setpoint settings - Setpoint for heating comfort = setpoint for
cooling comfort ................................................................58
Setpoint settings - Setpoint temperature for cooling comfort
(°C) .................................................................................60
Setpoint settings - Set-point temperature for frost protection
(°C) .................................................................................60
Setpoint settings - Set-point temperature for heat protection
(°C) .................................................................................61
Setpoint settings - Setpoint temperature for heating and
cooling comfort (°C) ........................................................59
Setpoint settings - Setpoint temperature for heating comfort
(°C) .................................................................................59
Settings of basic load ...........................................................56
Settings of basic load - Minimum control value for basic load
> 0 ...................................................................................56
Setup and function ...............................................................14
Software ...............................................................................24
Staircase lighting ................................................................108
Summer compensation ........................................................72
Summer compensation - (Lower) Starting temperature for
summer compensation (°C) ............................................73
Summer compensation - Offset of the set-point temperature
for the entry into summer compensation (x 0.1°C) .........73
Summer compensation - Offset of the set-point temperature
for the exit from summer compensation (x 0.1°C) ..........74
Summer compensation - Summer compensation ................72
Summer compensation active ..............................................89
Superimposed operating mode ............................................82
Switchover heating/cooling ..................................................84
T
Target group.........................................................................11
Technical data ......................................................................17
Temperature display – Temperature unit .............................75
Temperature reading - Adjustment value for internal
temperature measurement (x 0.1°C) ..............................66
Temperature reading - Control value for fault (0 - 255) ........67
Temperature reading - Cyclic sending of actual temperature
(min) ................................................................................66
Temperature reading - Difference of value for sending the
actual temperature (x 0.1°C) ...........................................66
Temperature reading - Inputs of temperature reading .........64
Temperature reading - Inputs of weighted temperature
reading ............................................................................65
Temperature reading - Monitoring time for temperature
reading (0 = no monitoring) (min) ....................................66
Temperature reading - Operating mode for fault..................67
Temperature reading - Weighting of external measurement (0
to 100%) ..........................................................................65
Temperature reading - Weighting of external measurement 2
(0 to 100%)......................................................................65
Temperature reading - Weighting of internal measurement (0
to 100%) ..........................................................................65
Threshold value / hysteresis ..............................................111
W
Window contact ....................................................................82
Application program
│116
Advertisement
Table of Contents
