Grandstream Networks HT818 Administration Manual

Hide thumbs Also See for HT818:

Administration manual (75 pages)

User manual (42 pages)

Quick installation manual (21 pages)

Table Of Contents

Table of Contents

Quick Links

Download this manual

Grandstream Networks, Inc.

HT818

Administration Guide

Table of Contents

Summary of Contents for Grandstream Networks HT818

Page 1 Grandstream Networks, Inc. HT818 Administration Guide...
Page 2: Product Overview
LAN and internet connections. This Grandstream Handy Tones are a new addition to the popular Handy Tone ATA product family. This manual will help you to learn how to operate and manage your HT818 analog telephone adaptor and make the best use of their many upgraded features including simple and quick installation, 3- way conferencing, direct IP-IP Calling, and new provisioning support among other features.
Page 3 Interfaces Telephone Eight (8) RJ11 FXS ports Interfaces Network Interface Two (2) 10/100/1000 Mbps Ethernet port (RJ45). LED Indicators POWER, LAN, WAN, PHONE1, PHONE2, PHONE3, PHONE4, PHONE 5, PHONE 6, PHONE 7 and PHONE 8. Factory Reset Yes. Button Voice, Fax, Modem Caller ID display or block, call waiting, flash, blind or attended transfer, forward, hold, do not disturb, 3-way Telephony Features conference.
Page 4: Getting Started
Check the package before installation. If you find anything missing, contact your system administrator. HT818 Ports Description The following figure describes the different ports on the back panel of the HT818. Figure 2: HT818 Back Panel Phone 1- 8 (HT818)
Page 5: Scenario 1: Connecting The Ht818 Using Wan Port
2. Connect the WAN port of the HT818 to a router, switch or modem using an Ethernet cable. 3. Insert the power adapter into the HT818 and connect it to a wall outlet and make sure to respect the technical specifications of the power adapter used.
Page 6: Ht818 Leds Pattern
Status Power LED The Power LED lights up when The HT818 is powered on and it flashes when the HT818 is booting up WAN LED The WAN LED lights up when The HT818 is connected to your network through the WAN port.
Page 7: Obtain Ht818 Ip Address Via Connected Analogue Phone
Obtain HT818 IP Address via Connected Analogue Phone HT818 is by default configured to obtain the IP address from DHCP server where the unit is located. In order to know which IP address is assigned to your HT818, you should access to the “Interactive Voice Response...
Page 8 Menu Voice Prompt Options Press “9” to move to the next selection in the list: PCM U / PCM A iLBC G-726 Preferred Vocoder G-723 G-729 OPUS G722 Announces the MAC address of the unit. “MAC Address” Note: The device has two MAC addresses. One for the WAN port and one for the LAN port. The device MAC address announced is the address of LAN port.
Page 9: Configuration Via Web Browser
For the initial setup, the Web access is by default enabled when the device is using private IP and disabled when using public IP, and you cannot access the Web UI of your HT818 until it’s enabled, the following steps will show you how to enable it via IVR.
Page 10: Saving The Configuration Changes
6. Make sure to reboot your device after changing your settings to apply the new configuration. Please make sure that your computer has a valid IP address on the range 192.168.2.x so you can access the web GUI of your HT818.
Page 11: Web Configuration Pages Definitions
1. Access your HT818 web UI by entering its IP address in your favorite browser. (the screenshot is taken from an HT80X model since the same configuration applies to the HT818 model) 2. Enter your admin password (default: admin). 3. Press Login to access your settings.
Page 12: Status Page Definitions
Hardware Displays the hardware revision information and the part number. Version Program: Specifies Program version. This is the main firmware release number, which is always used for identifying the software system of the HT818. Bootloader: Specifies Boot version. Software version Core: Specifies Core version.
Page 13: Basic Settings Page Definitions
Indicates type of NAT when it’s configured. Displays relevant information regarding the FXS ports about their registration, current Port Status status and their appropriate User ID. Port Displays relevant information regarding the FXS ports about their DND and call forward features. Options CDR File Download, Preview or, Delete call history records from the web GUI.
Page 14 Disable SSH Enables/disables the SSH access. Default is No (enabled). Allows users to self-conﬁgure SSH Port number. SSH Port By default, the port number is 22. SSH Idle Timeout Conﬁgures SSH session timeout. [0 – 86400] seconds; Default is 0. Disable Telnet Enables/disables the Telnet access. Default is Yes (disabled). Telnet Port Allows users to self-conﬁgure Telnet Port number. By default, the port number is 23.
Page 15 Conﬁgure IP address, subnet Mask, default router IP address, 1st preferred DNS server, Statically conﬁgured as IP address 2nd preferred DNS server. These ﬁelds are set to zero by default. Allows users to conﬁgure the appropriate network settings on the HT80x to obtain IPv6 address.
Page 16: Advanced Settings Page Definitions
● VOIP Data Reset: All ISP (Internet Service Provider) conﬁguration which may affect the IP address. ● Full Reset: Both VoIP and ISP related conﬁguration at the same time. Note: After you choose the reset type, you must click the reset button to take effect. Advanced Settings Page Definitions Deﬁnes the administrator level password to access the Advanced Web Conﬁguration page.
Page 17 Default is fm.grandstream.com/gs. Decrypts XML conﬁguration ﬁle when encrypted. The password used for encrypting the XML XML Conﬁg File Password conﬁguration ﬁle using OpenSSL. HTTP/HTTPS FTP/FTPS Enters username to authenticate with HTTP/HTTPS FTP/FTPS server. Username HTTP/HTTPS FTP/FTPS Enters password to authenticate with HTTP/HTTPS FTP/FTPS server. Password Checks if ﬁrmware ﬁle is with matching preﬁx before downloading it.
Page 18 Conﬁgure the HT8xx to search for the new ﬁrmware when the ﬁrmware preﬁx / sufﬁx changes. Check New Firmware only when When this option is selected, the HT8xx will check for updates only when the pre/sufﬁx has been F/W pre/sufﬁx changes changed.
Page 19 Sets the phone adapter system to enable the “CPE WAN Management Protocol” (TR-069). Enable TR-069 Default setting is Yes. TR-069 ﬁrewall rules Conﬁgures the TR-069 ﬁrewall rules , Value port range is 1-65535 Speciﬁes URL of TR-069 Auto Conﬁguration Servers (e.g., http://acs.mycompany.com), or IP address.
Page 20 Set RADIUS shared secret. Conﬁgure RADIUS VSA Vendor ID to match RADIUS server’s conﬁguration. Default is 42397 for RADIUS VSA Vendor ID Grandstream Networks Inc. RADIUS VSA Access Level Conﬁgure RADIUS VSA Access Level Attribute to match RADIUS server’s conﬁguration. Incorrect Attribute setting would cause Radius authenticate fail.
Page 21 Enable OpenVPN® Allow user to enable OpenVPN®. Default is No. OpenVPN® Server Address Specify the IP address or FQDN for the OpenVPN® Server. OpenVPN® Port Specify the listening port of the OpenVPN® server. Default is 1194 OpenVPN® Interface type Specify the Interface type of OpenVPN® whether TAP or TUN. Default is TUN. OpenVPN®...
Page 22 Disable Direct IP Call Direct IP call is disabled if set to Yes. Play Busy Tone When Account is When this feature is set to Yes, device will play busy tone when the FXS port account is not unregistered registered, and the attached analog phone is offhook. Allow users to block incoming calls from speciﬁc list of numbers.
Page 23 Upload Firmware computer. The ﬁrmware ﬁlename should be “ht80xfw.bin” (ht802fw.bin for HT802 for instance), "ht81xfw.bin” for HT812/HT814 or "ht818fw.bin” for HT818. Press Upload from local directory button to load conﬁguration ﬁle to the device from your computer. The conﬁguration ﬁle should be an XML ﬁle (for instance: “conﬁg.xml”). Note: The Upload Conﬁguration...
Page 24: Profiles Pages Definitions
Conﬁguration conﬁguration. E911/HELD Protocol: Enable E911 Enable Enhanced 911 call. Default is disabled HELD Protocol Conﬁgure HELD transfer protocol. HTTP or HTTPS The valid synchronization interval is between 30 to 1440 minutes. The synchronization is off HELD Synchronization Interval when the interval is 0. Location Server Conﬁgure the primary Location Information Server (LIS) address Location Server Username...
Page 25 (For example: proxy.myprovider.com, IPv4: 192.168.5.170, or IPv6: Proxy fe80::20b:82ff:fe75:211d). It’s Used by HT818 for ﬁrewall or NAT penetration in different network environments. If symmetric NAT is detected, STUN will not work and only outbound proxy can correct the problem Backup Conﬁgures the backup outbound proxy to be used when the “Outbound Proxy”...
Page 26 • Saved on until no response SIP request will always be sent to the registered IP address only until registered IP address is unreachable. When the primary SBC is up, device will send SIP requests to the primary SBC. If at any point device fails over to the Failback Timer secondary SBC, the SIP requests will stay on the failover SBC for the duration of the failback timer.
Page 27 Registration Failure Retry Sends re-register request after speciﬁc time (in seconds) when registration process fails with error 403 Forbidden. Wait Time Maximum interval is 3600 seconds (1 hour). Default is 1200 seconds. upon 403 Forbidden When set to Default, device will play Stutter Dial Tone when there is voicemail, if set to Special Proceed Indication MWI Tone Tone, device will play the conﬁgured special proceed indication tone upon user offhook when there is voicemail Enables SIP OPTIONS or SIP NOTIFY to track account registration status so the ATA will send periodic...
Page 28 Remove OBP Removes outbound proxy info in “Route” header when sending SIP packets. from Route Default is No. Header Includes “SIP Instance ID” attribute to “Contact” header in REGISTER request as deﬁned in IETF SIP outbound draft. Support SIP Instance ID Default is No.
Page 29 Header Uses Selects the Caller ID display order which need to be respected by the ATA. The available options are: Caller ID Fetch Auto: When set to “Auto”, the ATA will look for the caller ID in the order of P-Asserted Identity Header, Remote- Order Party-ID Header and From Header in the incoming SIP INVITE.
Page 30 When it set to YES it allows the user to perform some call setting when both channels are used while pressing: “Flash + 1” in order to hang up the current call and resume a call that was held. “Flash + 2” in order to hold the current call and resume a call that was held. Flash Digit “Flash + 3” in order to perform 3-way conference.
Page 31 Disable Enables / disables the warning to alert that the phone has been left off-hook for an extended period of time. Receiver Off Default is No. Hook Tone Disable Enables playing the reminder ring. Reminder Ring for On-Hold Default is No. Call Disable Reminder Ring This feature allows user to disable reminder ring when FXS port is on DND mode.
Page 32 This feature allows users to adjust the subscribe retry waiting time while it is rejected with 403 forbidden. Default is Subscribe 0. Valid range: 0-10080 in minutes. Retry Wait Note: Not supported on HT818 Time upon 403 Forbidden Send Sets “From”, “Privacy” and “P_Asserted_Identity” headers in outgoing INVITE message to “anonymous”, blocking Anonymous caller ID.
Page 33 Selects Soft switch vendors’ special requirements Examples of vendors: BroadSoft, CBCOM, RNK, Huawei, China Special Mobile, ZTE IMS, PhonePower, TELKOM SA, Vonage, Metaswitch, CenturyLink, MTS, Oi_BR, Telefonica, Feature GIBTELECOM. The default is Standard. Enable Disable the session timer when this option is set to “No”. By default, this option is enabled. Session Timer Enables SIP sessions to be periodically “refreshed”...
Page 34 Preferred Conﬁgures vocoders in a preference list (up to 8 preferred vocoders) that will be included with same order in SDP Vocoder message. Vocoder types are G.711 A-/U-law, G.726-32, G.723, G.729, iLBC and OPUS Voice Frames Transmits a speciﬁc number of voice frames per packet. Default is 2; increases to 10/20/32/64 for per TX G711/G726/G723/other codecs respectively.
Page 35 SLIC Setting Depends on standard phone type (and location). Caller ID Selects the caller id scheme, for example: Bellcore/Telcordia, ETSI-FSK … Scheme DTMF Caller Deﬁnes the start and stop tones (Default, A, B, C, D or #) to delimit CID. Disable analog phone’s caller ID when receiving a call with “Anonymous”, “unavailable”...
Page 36 parameter under the FXS port conﬁguration page. If voice volume is too low at the other end, user may increase the far end volume using the Tx gain level parameter under the FXS port conﬁguration PAGE. Disables the LEC per call base. Recommended for Fax/Data calls. Disable Line Echo Canceller Default is No.
Page 37 Default is f1=440@-13,c=300/10000; Call Features Settings When enabled, Do No Disturb, Call Forward and other call features can be used via the local feature codes on the Enable Call phone. Otherwise, the ITSP feature codes will be used. Enable All will override all individual features enable setting. Features Default is Yes Allows users to reset all call features conﬁguration.
Page 38: Fxs Ports Page Definitions
– Enable DND: Default is 78 – Disable DND: Default is 79 Blind Transfer Allow users to customize the Blind Transfer feature code. Default is Yes Feature – Enable Blind Transfer: Default is 87 Disable LEC Default is Yes per call – Disable LEC per call: Default is 03 Feature Disable Bellcore Style...
Page 39: Important Settings
Hunting Group 1 contains ports 1, 2, 3. FXS port 4 is registered but it is not added to the Hunting Group 1. Note: HT818 will use CID name from FXS port initiating the outgoing call if the “Name” field is entered for that specific port.
Page 40: Configuring Ht818 Through Voice Prompts
Select voice menu option 01 to enable HT818 to use DHCP. STATIC IP MODE Select voice menu option 01 to enable HT818 to use STATIC IP mode, then use option 02, 03, 04, 05 to set up IP address, Subnet Mask, Gateway and DNS server respectively.
Page 41: Configuration Through A Central Server
Register a SIP Account The HT818 support 2 profiles which can be configured with 2 SIP accounts. Please refer to the following steps to register your accounts via web user interface 1. Access your HT818 web UI by entering its IP address in your favorite browser.
Page 42 Figure 9: SIP Accounts settings After applying your configuration, your account will register to your SIP Server, you can verify if it has been correctly registered with your SIP server from your HT818 web interface under Status �� Port Status ��...
Page 43: Call Features
When all the FXS ports are registered, the simultaneous ring will have one second delay between each ring on each phone. Call Features The HT818 support all the traditional and advanced telephony features. Call Features Forcing a Codec (per call) *027110 (PCMU), *027111 (PCMA), *02723 (G723), *02729 (G729), *027201 (iLBC), *02722 (G722).
Page 44: Rebooting Ht818 From Remote
Pressing pound sign will serve as Re-Dial key. Table 11: HT818 Call Features Rebooting HT818 from Remote Press “Reboot” button at the bottom of the configuration menu to reboot the ATA remotely. The web browser will then display a...
Page 45: Upgrading And Provisioning
“Firmware Server Path” field and choose to upgrade via TFTP, HTTP/HTTPS or FTP/FTPS. 5. Make sure to check “Always Check for New Firmware”. 6. Update the change by clicking the “Apply” button at the bottom of the page. Then “Reboot” or power cycle the HT818 to update the new firmware.
Page 46: Firmware And Configuration File Prefix And Postfix
3. From the HT818 web interface (Advanced Settings page) you can browse your hard drive and select the folder you previously saved the file (HT8xfw.bin) 4. Click “Upload Firmware” and wait few minutes until the new program is loaded. Always check the status page to see that the program version has changed.
Page 47: Configuration File Download
When the HT818 boots up or reboots, it will send a request to download a file named “cfgxxxxxxxxxxxx” followed by a configuration XML file named “cfgxxxxxxxxxxxx.xml”, where “xxxxxxxxxxxx” is the MAC address of the phone, i.e., “cfg000b820102ab” and “cfg000b820102ab.xml”.
Page 48: Reset From Web Interface (Reset Type)
Factory Reset will be disabled if the “Lock keypad update” is set to “Yes”. If the HT818 were previously locked by your local service provider, pressing the RESET button will only restart the unit. The device will not return to factory default settings.
Page 49: Change Log
(if no SIP account is configured) or using SIP account credentials. CHANGE LOG This section documents significant changes from previous versions of the admin guide for HT818. Only major new features or major document updates are listed here. Minor updates for corrections or editing are not documented here.
Page 50 Updated CDR File Option | SIP File Option (P8534/8535) value from “1 – Override” to “Overwrite”. [Advanced Settings Page Definitions] Added Local IVR option that announces extension number of the port. [Understanding HT818 Interactive Voice Prompt Response Menu] Firmware Version 1.0.37.1 Added feature Configuration File Types Allowed.
Page 51 Firmware Version 1.0.21.4 Added support for IPv6 address without square brackets. [Primary SIP Server][Failover SIP Server][Outbound Proxy][Backup Outbound Proxy] Added support for DHCP Domain Name configuration. [DHCP domain name] Added support of “Use Configured IP” for “DNS Mode”. [Use Configured IP] Added support for “Play Busy Tone When Account is unregistered”.
Page 52 Added support to display WAN/LAN port cable status on the Web UI. [Network Cable Status] Firmware Version 1.0.9.3 Added support for G722 (wide-band) codec. [HT818 Technical Specifications] Added support for FTP/FTPS for provision and firmware upgrade. [UPGRADING AND PROVISIONING] Added feature “Conference Party Hang-up Tone” when “Special Feature” is set to MTS. [Call Progress Tones] Firmware Version 1.0.8.7...
Page 53 Need Support? Can’t find the answer you’re looking for? Don’t worry we’re here to help! CONTACT SUPPORT...

Grandstream Networks HT818 Administration Manual

Quick Links

Related Manuals for Grandstream Networks HT818

Summary of Contents for Grandstream Networks HT818

Table of Contents