Planet IGS-6325 Series Quick Installation Manual
  1. Manuals
  2. Brands
  3. Planet Manuals
  4. Switch
  5. IGS-6325 Series
  6. Quick installation manual

Planet IGS-6325 Series Quick Installation Manual

Industrial l3 rack-mount managed ethernet switch
Hide thumbs Also See for IGS-6325 Series:
Table of Contents

Advertisement

Quick Links

Industrial L3 Rack-mount
Managed Ethernet Switch
IGS-6325 Series
Quick Installation Guide

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the IGS-6325 Series and is the answer not in the manual?

Questions and answers

Related Manuals for Planet IGS-6325 Series

Summary of Contents for Planet IGS-6325 Series

  • Page 1 Industrial L3 Rack-mount Managed Ethernet Switch IGS-6325 Series Quick Installation Guide...

  • Page 2: Table Of Contents

    Table of Contents 1. Package Contents ..................3 2. Requirements ..................... 4 3. Wiring DC Power Inputs ................5 4. Terminal Setup ................... 6 4.1 Logging on to Console ................. 7 4.2 Configuring IP Address via Console ............8 5. Starting Web Management .................10 5.1 Logging in to the Industrial Managed Switch .........10 5.2 Saving Configuration via Web ..............13 6. Recovering Back to Default Configuration .............15...

  • Page 3: Package Contents

    1. Package Contents Thank you for purchasing PLANET Industrial L3 Managed Ethernet Switch. “Industrial Managed Switch” is used as an alternative name in this Quick Installation Guide. Open the box of the Industrial Managed Switch and carefully unpack it. The box...

  • Page 4: Requirements

    2. Requirements The Industrial Managed Switch provides remote login interface for management purposes. The following equipment is necessary for further management: z Workstations running Windows 2003/2008/XP/Vista/7/8/10, MAC OS X or later, Linux, UNIX, or other platforms are compatible with TCP/IP Protocols. z Serial Port Connection (Terminal)  The above Workstations come with COM Port (DB9) or USB-to-RS232 converter.

  • Page 5: Wiring Dc Power Inputs

    3. Wiring DC Power Inputs The 6-contact terminal block connector on the panel of Industrial Managed Switch is used for two DC redundant power inputs. Please use the correct DC input voltage and follow the steps below to insert the power wires. 1. Insert positive and negative DC power wires into contacts 1 and 2 for DC POWER 1, or 5 and 6 for DC POWER 2.

  • Page 6: Terminal Setup

    4. Terminal Setup To configure the system, connect a serial cable to a COM port on a PC or notebook computer and to RJ45 type of serial port of the Industrial Managed Switch. PC / Workstation with Terminal Emulation Software Managed Switch RS232 to RJ45 Cable Serial Port...

  • Page 7: Logging On To Console

    4.1 Logging on to Console Once the terminal is connected to the device, power on the Industrial Managed Switch and the terminal will display “running testing procedures”. Then, the following message asks to log in user name and password. The factory default user name and password are shown as follows as the login screen in Figure 4-3 appears. Username: admin Password: admin Figure 4-3: Industrial Managed Switch Console Login Screen The user can now enter commands to manage the Industrial Managed Switch. For a detailed description of the commands, please refer to the following chapters.

  • Page 8: Configuring Ip Address Via Console

    4.2 Configuring IP Address via Console The Industrial Managed Switch is shipped with default IP address shown below. IP Address: 192.168.0.100 Subnet Mask: 255.255.255.0 To check the current IP address or modify a new IP address for the Switch, please use the procedures as follows:  Show the current IP Address 1. At the “#” prompt, enter “show ip interface brief”. IGS-6325-20T4C4X # show ip interface brief 2. The screen displays the current IP address as shown in Figure 4-4. Figure 4-4: IP Information Screen  Configuring IP Address 3. At the “#” prompt, enter the following command and press <Enter>...
  • Page 9 4. Repeat step 1 to check if the IP address is changed.  Storing current switch configuration 5. Enter the following command and press <Enter> to go back to “#” prompt. # exit Figure 4-6: Inputting Exit Command Screen 6. At the “#” prompt, enter the following command and press <Enter>. # copy running-config startup-config Figure 4-7: Saving Current Configuration Command Screen If the IP is successfully configured, the Industrial Managed Switch will apply the new IP address setting immediately. You can access the Web interface of the Industrial Managed Switch through the new IP address.

  • Page 10: Starting Web Management

    5. Starting Web Management The following shows how to start up the Web Management of the Industrial Managed Switch. Note the Industrial Managed Switch is configured through an Ethernet connection. Please make sure the manager PC must be set to the same IP subnet address.
  • Page 11 Default Username: admin Default Password: admin Figure 5-2: Login Screen 3. After entering the password, the main screen appears as Figure 5-3 shows. Figure 5-3: Web Main Screen of Industrial Managed Switch...
  • Page 12 The Switch Main Menu is shown on top of the Web page, and the functions are shown on the left to configure the Industrial Managed Switch. Figure 5-4: Switch Menu Now, you can use the Web management interface to continue the Switch management or manage the Switch by console interface. Please refer to the user’s manual for more.

  • Page 13: Saving Configuration Via Web

    5.2 Saving Configuration via Web In the Industrial Managed Switch, the running configuration stores in the RAM. In the current version, the running configuration sequence of running-config can be saved from the RAM to FLASH by executing save startup config command, so that the running configuration sequence becomes the startup configuration file, which is called configuration save.
  • Page 14 2. Or you can press the “Save Configuration” button. Figure 5-7: Save Configuration Button 3. Press the “Save Configuration” button to save Figure 5-8: Save Configuration...

  • Page 15: Recovering Back To Default Configuration

    6. Recovering Back to Default Configuration  IP address has been changed or admin password has been forgotten – To reset the IP address to the default IP address “192.168.0.100” or reset the login password to default value, press the hardware-based reset button on the rear panel for about 10 seconds. After the device is rebooted, you can log in the management Web interface within the same subnet of 192.168.0.xx.

  • Page 16: Customer Support

    7. Customer Support Thank you for purchasing PLANET products. You can browse our online FAQ resource and User’s Manual on PLANET Web site first to check if it could solve your issue. If you need more support information, please contact PLANET support team. PLANET online FAQs: http://www.planet.com.tw/en/support/faq Support team mail address: support@planet.com.tw IGS-6325 Series User’s Manual: https://www.planet.com.tw/en/support/downloads?&method=keyword&keyword=I GS-6325&view=3#list (Please select the suitable user’s manual from the list.) Copyright © PLANET Technology Corp. 2019. Contents are subject to revision without prior notice. PLANET is a registered trademark of PLANET Technology Corp.

This manual is also suitable for:

Igs-6325-20t4c4xIgs-6325-20s4c4xIgs-6325-24p4xIgs-6325-24p4s

Table of Contents