Color guides: Color differences may occur due to different printing and publication methods. ASSA ABLOY, Crawford, Megadoor and hafa, as words and logos, are examples of trademarks owned by ASSA ABLOY Entrance Systems or companies within the ASSA ABLOY Group.
MCS-R Control unit Installation Manual replacing ECS 430P or older control units for CDM5 & 6 Contents Copyright and Disclaimer Notice ..........................2 Contents ....................................3 About this Manual ..............................4 Safety Symbols Used in this Manual ................................. 4 MCS-R control unit ..............................5 Installation ..........................................
MCS-R Control unit Installation Manual replacing ECS 430P or older control units for CDM5 & 6 1. About this Manual All users and owners of the Industrial door must read, understand and obey the information and instructions in this manual. Failure to do so may result in damage to, or failure of the equipment, and possible injury to persons. This manual contains functional descriptions and installation information for a Industrial door.
MCS-R Control unit Installation Manual replacing ECS 430P or older control units for CDM5 & 6 2. MCS-R control unit Installation 1) At the rear of the control unit you have to assemble 4 enclosure brackets before mounting it to the wall. Use the four small 5x12 screws.
MCS-R Control unit Installation Manual replacing ECS 430P or older control units for CDM5 & 6 Technical data Dimensions: 350 x 200 x 120 mm Main supply voltage L1, L2, L3, N, PE: 400V 50Hz Fuse protection: 10A K- characteristic Voltage: 24V DC, max.
MCS-R Control unit Installation Manual replacing ECS 430P or older control units for CDM5 & 6 MCS-R menu overview 1) Display 2) Keypad 3) Push-button "UP" (door opens) 4) Push-button "STOP" (door stays in position) 5) Push button "DOWN" (door closes) Menu selection (left) Menu selection (right) Confirm...
MCS-R Control unit Installation Manual replacing ECS 430P or older control units for CDM5 & 6 Programming Before programming the control unit: Place the door 1.5m above the floor. Ensure that the floor is clean and free from cables etc. Programming can only be carried out using the set of buttons in the control box, not an external push button box or radio control.
MCS-R Control unit Installation Manual replacing ECS 430P or older control units for CDM5 & 6 2.4.2 Motor setup 1) Use the buttons to navigate to the "Motor setup" menu. 2) Press to enter the menu. 3) Use the buttons to select one of the following menu items: 1) "Motor direction"...
MCS-R Control unit Installation Manual replacing ECS 430P or older control units for CDM5 & 6 2.4.4 Code entry Factory setting code is "00000". If a new code is set, it is impossible to enter the programming mode again unless the correct code is used.
MCS-R Control unit Installation Manual replacing ECS 430P or older control units for CDM5 & 6 2.4.6 Safety devices This function is not used together with the "dead man down"-function. 1) Use the buttons to navigate to the "Safety rail" menu. Press to enter the menu.
MCS-R Control unit Installation Manual replacing ECS 430P or older control units for CDM5 & 6 2.4.7 Service 1) Use the buttons to navigate to the "Service" menu. 2) Press to enter the menu. 3) Use the buttons to select one of the following menu items: 1) "Cycles"...
MCS-R Control unit Installation Manual replacing ECS 430P or older control units for CDM5 & 6 7) To view the event and error history navigate to the "Event history" menu item and press to enter the menu item. Use button to navigate trough the history. 8) To clear the event history navigate to the "Clear event history"...
Page 14
MCS-R Control unit Installation Manual replacing ECS 430P or older control units for CDM5 & 6 2.4.8.2 Photocell function 1) In the "Special setup" menu use the button to navigate to the "Safety device" menu. 2) Use the buttons to select the 4-wire photocell function. 1) Select "Untested".
Page 15
MCS-R Control unit Installation Manual replacing ECS 430P or older control units for CDM5 & 6 2.4.8.4 Door control mode 1) In the "Special setup" menu use the button to navigate to the " Door control mode" menu. 2) In the "Door control mode" menu you are able to choose between "Sectional door" (default) or "High speed door." 3) For the MCS-R choose "Sectional door".
Page 16
ASSA ABLOY Entrance Systems is a leading supplier of entrance automation solutions for efficient flow of goods and people. With our worldwide presence we offer products and services dedicated to satisfying end-user needs for safe, secure, convenient and sustainable operations.
Need help?
Do you have a question about the Crawford MCS-R and is the answer not in the manual?
Questions and answers