Advertisement
Quick Links
interpret
Section:
Description:
NOTE: Refer to INT_404
for Power Door installation.
A
B
Leveler Cover is
located inside Leg,
assembled and
secured in place
with tape.
NOTE: Curve Leg without infill
layout shown.
E
D
A
B
C1, C2
A
Date:
INT_012b
Part and Product Identification
A
See page INT_012b_G02
for more information
B -Connect Bracket
(A16-1383) x3
C1 -Center Leg Assembly
(N02-2268) x1
C2 -Leveler Cover
(A23-3670\03) x1
D
Worksurface
(WWWTC) x1
E
Worksurface
(WWWTW) x2
NOTE: Quantities and types of Worksurfaces shown as an
example.
For Customer Support please contact
product.support@teknion.com
Feb 2017
Page No:
1 of 11
Rev. No: 1
Advertisement
Subscribe to Our Youtube Channel
Related Manuals for Teknion interpret 120 FRAME CURVE LEG WWSTW
Summary of Contents for Teknion interpret 120 FRAME CURVE LEG WWSTW
- Page 1 (WWWTC) x1 Leveler Cover is located inside Leg, assembled and Worksurface secured in place (WWWTW) x2 with tape. NOTE: Quantities and types of Worksurfaces shown as an example. NOTE: Curve Leg without infill layout shown. For Customer Support please contact product.support@teknion.com...
- Page 2 NOTE: 3 Curve Legs without Infill (E01-0756) x4 A11 -5/16X18 Hex A23 - 5/16X18 Hex Frames are shown in this guide. Nut, 1/2 A/F Nut, 1/2 A/F For Customer Support please contact . 265 THK . 265 THK product.support@teknion.com (E01-0755) x4 (E01-0755) x4...
- Page 3 interpret Section: Date: Feb 2017 Page No: 3 of 11 Description: INT_012b REMOVE SCREWS - END GABLE CONNECTION DETAIL Curve Leg A8, A12 Connections STEP 1: Remove Screws and Nuts from Beams required for Curve Leg installation. Save them SIDE VIEW for future installation.
- Page 4 interpret Section: Date: Feb 2017 Page No: 4 of 11 Description: INT_012b PREPARE CURVE LEG FOR INSTALLATION ATTACH CENTRE WING BEAM TO CURVE LEG NOTE: There are 3 Curve Legs required Curve Leg Connection Side view for this layout. STEP 2: Remove Leveler Add on Pucks from all 3 Curve Legs. STEP 3: Attach longer, Center Beams to both End Gables using sets of holes in the middle, as shown.
- Page 5 interpret Section: Date: Feb 2016 Page No: 5 of 11 Description: INT_012b FASTEN CONNECT TO CENTER LEG ASSEMBLY NOTE: Reverse Screws and Nuts when Curve Leg glass or solid Mid Gable Connection infill is present. STEP 4: Fasten with previously removed Screws and Nuts, do not tighten. Repeat with STEP 5: Bring Curve Leg and Center Beam assemblies to the Center Leg assembly.
- Page 6 interpret Section: Date: Feb 2017 Page No: 6 of 11 Description: INT_012b ATTACH WING BEAM ASSEMBLIES FASTEN TO CURVE LEGS NOTE: Reverse Screws and Nuts when Curve Leg glass or solid infill is present. STEP 7: Fasten with previously saved Screws and Nuts. STEP 6: Align Wing Beam Assemblies with holes on Curve Legs.
- Page 7 interpret Section: Date: Feb 2017 Page No: 7 of 11 Description: INT_012b JOIN WING BEAMS TOGETHER ATTACH CROSS BARS NOTE: Do NOT fully tighten NOTE: Do NOT fully tighten STEP 8: Remove Screws and Nuts from the ends of the Wing Beams. Line up Connecting STEP 9: Line up middle holes on Cross Bars with holes on beams as shown and place them on Brackets with indicated holes on Wing Beams.
- Page 8 interpret Section: Date: Feb 2017 Page No: 8 of 11 Description: INT_012b CANTILEVERS AND SPACERS PLACEMENT CENTRE RAIL ASSEMBLY Side view (Both sides) Tighten set screws NOTE: Install electrical components if specified. Refer to INT_401a, 406a, 408c Guides. STEP 10: Line up Cantilevers' middle holes with the holes on the Beams, as shown above. STEP 11: Insert Hex Cap Screws inside the underside channels.
- Page 9 interpret Section: Date: Feb 2017 Page No: 9 of 11 Description: INT_012b CENTRE RAIL INSTALLATION INSTALL ADD ON PUCKS AND LEVEL COVER Install only if screens or storage are not specified Curve End Cap, both sides NOTE: Use as many Pucks as required.They have to be FULLY ENGAGED and there should be NO SPACE between Pucks and the bottom of Curve Leg frame.
- Page 10 interpret Section: Date: Feb 2017 Page No: 10 of 11 Description: INT_012b ALIGN TO INSTALL WORKSURFACES TIGHTEN ALL SCREWS AND NUTS NOTE: For Curve Legs WITH INFILL, please lift Worksurfaces up and tighten all Screws and Nuts and then fasten Worksurfaces to the Frame. STEP 15: Tighten Screws and Nuts STEP 14: Place Worksurfaces on the top of the frame aligning Clamp Brackets holes with Worksurfaces' inserts as shown.
- Page 11 product line Section: Date: Feb 2017 Page No: 11 of 11 Description: INT_012b FASTEN TO CANTILEVERS AND CROSS BAR DETAIL Underside View STEP 16: Fasten Worksurfaces to Cantilevers and Cross Bars with Pan head Wood Screws.
Need help?
Do you have a question about the interpret 120 FRAME CURVE LEG WWSTW and is the answer not in the manual?
Questions and answers