ADB Safegate AXON FAA L-852AL User Manual

Hide thumbs

Table Of Contents

Table of Contents

Quick Links

Download this manual

AXON Taxiway Inset Lights, 8-inch and 12-inch

FAA L-852A(L), L-852B(L), L-852C(L), L-852D(L),

L-852J(L), L-852K(L) Centerline; L-852S(L) Stop Bar;

Triple Line Centerline Narrow, Wide, Curved;

ICAO Centerline Narrow, Wide, Curved;

Runway Entrance Light (REL, RWSL);

Enhanced Rapid Exit;

ICAO Stop Bar;

User Manual

Table of Contents

Need help?

Do you have a question about the AXON FAA L-852AL and is the answer not in the manual?

Questions and answers

Summary of Contents for ADB Safegate AXON FAA L-852AL

Page 1 AXON Taxiway Inset Lights, 8-inch and 12-inch FAA L-852A(L), L-852B(L), L-852C(L), L-852D(L), L-852J(L), L-852K(L) Centerline; L-852S(L) Stop Bar; Triple Line Centerline Narrow, Wide, Curved; ICAO Centerline Narrow, Wide, Curved; Runway Entrance Light (REL, RWSL); Enhanced Rapid Exit; ICAO Stop Bar; User Manual...
Page 2 UM-5056, Rev. 1.0.17, 2022/12/08...
Page 3 Material Handling Precautions and Storage precautions that must be followed. ADB SAFEGATE reserves the right to examine goods upon which a claim is made. Said goods must be presented in the same condition as when the defect therein was discovered. ADB SAFEGATE furthers reserves the right to require the return of such goods to establish any claim.
Page 4 This manual could contain technical inaccuracies or typographical errors. ADB SAFEGATE BV reserves the right to revise this manual from time to time in the contents thereof without obligation of ADB SAFEGATE BV to notify any person of such revision or change. Details and values given in this manual are average values and have been compiled with care. They are not binding, however, and ADB SAFEGATE BV disclaims any liability for damages or detriments suffered as a result of reliance on the information given herein or the use of products, processes or equipment to which this manual refers.
Page 5: Table Of Contents
6.1 Ordering Code L852-A/B/C/D/J/K-(L), LED Taxiway Centerline, Lead-on/Exit, Apron Lead-in (FAA) ........42 6.2 Ordering Code LED Taxiway Centerline (ICAO) ............................44 6.3 Ordering Code LED Triple Line Taxiway Centerline Light ........................46 6.4 Ordering Code LED Stopbar (ICAO) ................................48 UM-5056, Rev. 1.0.17, 2022/12/08 Copyright ADB Safegate, All Rights Reserved ©...
Page 6 B.0 INTEROPERABILITY ................................77 C.0 POWER TABLE ..................................81 D.0 CABLE LOSS ..................................83 E.0 SUPPORT ....................................85 E.1 ADB SAFEGATE Website ....................................... 85 E.2 Recycling ............................................ 85 E.2.1 Local Authority Recycling ..................................85 E.2.2 ADB SAFEGATE Recycling ..................................86...
Page 7 Figure 33: Pressure release screws, package of 5 ............................... 57 Figure 34: Fig. 1 — Snowplow blade with well aligned segments ........................74 Figure 35: Fig. 2 — Snowplow blade with wear and steps between segments ....................74 UM-5056, Rev. 1.0.17, 2022/12/08 Copyright ADB Safegate, All Rights Reserved ©...
Page 8 Figure 36: Fig. 3 — Snowplow blade without clearance ............................75 Figure 37: Fig. 4 — Snowplow with support wheels ..............................75 Figure 38: Fig. 5 — Snowplow without support wheels ............................75 viii Copyright ADB Safegate, All Rights Reserved ©...
Page 9 Table 1: Suggested Tools and Materials for Installation and Repair ........................19 Table 2: Interoperability matrix — 12 inch ..................................77 Table 3: Interoperability matrix — 8 inch ..................................78 UM-5056, Rev. 1.0.17, 2022/12/08 Copyright ADB Safegate, All Rights Reserved ©...
Page 11: Safety
1.0 Safety Introduction to Safety This section contains general safety instructions for installing and using ADB SAFEGATE equipment. Some safety instructions may not apply to the equipment in this manual. Task- and equipment-specific warnings are included in other sections of this manual where appropriate.
Page 12: Introduction To Safety
Using this equipment in ways other than described in this manual may result in personal injury, death or property and equipment damage. Use this equipment only as described in this manual. Failure to follow this instruction can result in serious injury or equipment damage Copyright ADB Safegate, All Rights Reserved ©...
Page 13: Material Handling Precautions: Storage
Allow only qualified personnel to make repairs. Repair or replace the malfunctioning component according to instructions provided in its manual. Failure to follow these instructions can result in death or equipment damage UM-5056, Rev. 1.0.17, 2022/12/08 Copyright ADB Safegate, All Rights Reserved ©...
Page 14: Material Handling Precautions: Fasteners
Note To minimize the risk of errors, the ADB SAFEGATE Sales Representative will have information on which gasket goes with which base. This information is also provided in the product Data sheets, the User Manuals and the Spare Part Lists.
Page 15: About This Manual
Triple Line Taxiway Centerline Light (3C, 3N, 3W) 2.1 How to work with the Manual • Familiarize yourself with the structure and content. • Carry out the actions completely and in the given sequence. UM-5056, Rev. 1.0.17, 2022/12/08 Copyright ADB Safegate, All Rights Reserved ©...
Page 16: Abbreviations And Terms
International Civil Aviation Organization International Electrotechnical Committee ILCMS Individual Light Control and Monitoring System Light Emitting Diode NATO North Atlantic Treaty Organization STAC Service Technique de l'Aviation Civile (France) STANAG Standardization Agreement (NATO) Copyright ADB Safegate, All Rights Reserved ©...
Page 17: Introduction
Style-6 cord set Style-1 jacketed cord set Note EQ light fixtures are not fail-open light fixtures. The monitoring as well as the control functionality is handled by the ILCMS system. UM-5056, Rev. 1.0.17, 2022/12/08 Copyright ADB Safegate, All Rights Reserved ©...
Page 18: Product Information
5052 5054 5070 AC 150/5345-46 and the FAA Engineering Brief No. 67 ICAO Annex 14 Volume 1 EASA CS-ADR-DSN Australia MOS 139 Canada TP 312 61827 NATO STANAG 3316 STAC PRO/STAC/SE/VIS CAP 168 Copyright ADB Safegate, All Rights Reserved ©...
Page 19 FAA Runway Status Light (RWSL) Applications • L-850T(L) THL Runway Takeoff/Hold Light • L-850T(L) RIL Runway Intersection Light • REL Runway Entry Light Note Refer to Runway manual UM-5055 for information on L-850T(L). UM-5056, Rev. 1.0.17, 2022/12/08 Copyright ADB Safegate, All Rights Reserved ©...
Page 20 5,000 A Power Supply Options • Non-Monitored — Power only • Monitored — integrated Fail-open technology • EQ with integrated ILCMS with OFDM technology for use with LINC 360 system. Copyright ADB Safegate, All Rights Reserved ©...
Page 21 Operating temperature -60 °C to +55 °C / -76 °F to +131 °F Storage temperature -60 °C to +80 °C / -76 °F to +176 °F Humidity Up to 100% UM-5056, Rev. 1.0.17, 2022/12/08 Copyright ADB Safegate, All Rights Reserved ©...
Page 22: Dimensions And Weight
3 kg / 6.6 lb (8 in) 203 mm / 8 in FAA SB-TA-TB-TC-TD-TJ-TK ICAO SB-TC-TK-TR-TW-3C-3N-3W; 6.8 kg / 15 lb (12 in) 305 mm / 12 in FAA SB-TA-TB-TC-TD-TJ-TK Figure 2: 8-inch Taxiway Lights Copyright ADB Safegate, All Rights Reserved ©...
Page 25: Installation
Install the inset light fixture in a base provided by ADB SAFEGATE as follows: Note If the inset light fixture is to be installed on another type of base or adapter ring not provided by ADB SAFEGATE, contact ADB SAFEGATE.
Page 26: Installation Overview
See data sheet A.05.120 or DS2012 for more information on base cans. 4.3.2 INTEROPERABILITY Top cover versions Note Please check interoperability matrix for information on torque values and compatibility towards different bases. Copyright ADB Safegate, All Rights Reserved ©...
Page 27: Typical L-868 Assembly
TRANSFORMER SUPPORT (TYP.) 3/4" DRAIN HOLE (CENTERED) 1. Torque according to: FAA EB-83 (latest revision). Figure 6: Anti-vibration washer example Cams (or steps) of the lock-washer must face each other UM-5056, Rev. 1.0.17, 2022/12/08 Copyright ADB Safegate, All Rights Reserved ©...
Page 28: Safety Considerations
Failure to follow these safety procedures can result in personal injury or death. • Allow only qualified personnel to install ADB SAFEGATE and auxiliary equipment. Use only approved equipment. Using unapproved equipment in an approved system may void FAA approvals. Observe and follow the safety instructions in this document and all other related documentation.
Page 29: Verify Input Requirements And Equipment Needed
PID/SN and position of the light fixture in, for example, a site documentation table. The information is required for remote activation and administration of control and monitoring functionality from a substation. UM-5056, Rev. 1.0.17, 2022/12/08 Copyright ADB Safegate, All Rights Reserved ©...
Page 30: Inspect On Delivery
These light fixtures have a top cover with the toe-in cast in place at an appropriate angle Figure 7: Toe-in Mechanical toe-in, ICAO narrow/w ide; Side 1 left toe, side 2 right toe, FAA L-852A-D(L) ICAO curved ; FAA L-852J/K(L) Copyright ADB Safegate, All Rights Reserved ©...
Page 31: Unpacking The Unit
PID/SN and position of the light fixture in, for example, a site documentation table. The information is required for remote activation and administration of control and monitoring functionality from a substation. UM-5056, Rev. 1.0.17, 2022/12/08 Copyright ADB Safegate, All Rights Reserved ©...
Page 32: Light Emission Directions
The color of the emitted light is indicated with a painted dot on the top cover in front of the prism. Toe-in is per the stamped directional arrow. Figure 8: Light emission directions Right toe Left toe Straight (uni-directional) Curved Straight (bi-directional) Color Color code White Yellow Green G or F Blue Copyright ADB Safegate, All Rights Reserved ©...
Page 33: Maintenance
Spare parts are available, if required. For more information, see www.adbsafegate.com and the Spare Parts List document, or contact ADB SAFEGATE for assistance. CAUTION Use of incorrect combination of gaskets, bolts and nuts can create severe damages to the product installation and create multiple safety risks.
Page 34: Basic Maintenance Program
Any issues found during maintenance tasks should be corrected accordingly and properly documented. A proper asset management system such as ADB Safegate's ALIS can help to store/document data and can provide valuable information on local presiding conditions for preventive maintenance planning. This can then be used to minimize the need for reactive maintenance.
Page 35: Recommended Maintenance Program For Optimal Service Life
Green – Areas outside Red and Amber areas NOTICE It is recommended that there is a reliable means of recording the location history of fittings (similar to ADB Safegate ALIS) to ensure that the maximum duration in critical areas (RED) of the runway are not exceeded.
Page 36: Figure 9: Preventive Maintenance
You can also increase the service life of a light fixture by rotating the installation location of light fixtures in critical areas. Regular inspections and well-defined preventive maintenance planning will help to reduce the overall maintenance cost and reduce downtime from reactive maintenance tasks. Figure 9: Preventive Maintenance Copyright ADB Safegate, All Rights Reserved ©...
Page 37: Recommendation
To relax the recommended frequencies of some maintenance tasks i.e. torque management, data is needed for justification. • Policies have a direct link with the age of the AGL and should also be tracked and recorded. UM-5056, Rev. 1.0.17, 2022/12/08 Copyright ADB Safegate, All Rights Reserved ©...
Page 38 Contact to your local sales representative if you have any questions or would require some assistance to go through local conditions and see how we can help establish a well-defined maintenance planning to optimize the expected service life of your investment. Copyright ADB Safegate, All Rights Reserved ©...
Page 39: Workshop Maintenance
Pull carefully to disconnect the wires between the converter and the heater kit(s), if the heater kit is in place. 6. Remove the gasket between the Top Cover Assembly and the Inner Pan Assembly. Make sure you dispose the old gasket and use a new gasket. UM-5056, Rev. 1.0.17, 2022/12/08 Copyright ADB Safegate, All Rights Reserved ©...
Page 40: Closing A Light Fixture - Connecting The Bottom Pan To The Top Cover
Use new fixation screws to torque in star pattern at 31 in-lbs (3.5 Nm). b. Retorque the screws in star pattern at 31 in-lbs (3.5 Nm). 7. Follow the water-tightness test procedure. Note Refer to the Checking the Light Fixture for Water-tightness section. Copyright ADB Safegate, All Rights Reserved ©...
Page 41: Replacing The Power Wire Harness
Figure 12: LED bracket removal 3. Disconnect the old wire harnesses. Make sure you dispose the old wire harnesses and use new wire harnesses. 4. Connect the new wire harnesses. UM-5056, Rev. 1.0.17, 2022/12/08 Copyright ADB Safegate, All Rights Reserved ©...
Page 42 5. Mount the LED bracket with new screws at 26 in-lbs (3 Nm). 6. Close the light. Note Refer to the Closing a Light Fixture — connecting the Bottom Pan to the Top Cover section. Copyright ADB Safegate, All Rights Reserved ©...
Page 43: Replacing The Light Engine Assembly
Refer to the Opening a Light Fixture — disconnecting the Bottom Pan from the Top Cover section. 2. Remove the Light engine (4 M4 screws per light engine assembly). UM-5056, Rev. 1.0.17, 2022/12/08 Copyright ADB Safegate, All Rights Reserved ©...
Page 44: Replacing The Top Cover Assembly
Closing a Light Fixture — connecting the Bottom Pan to the Top Cover section. 5.3.6 Replacing the Top Cover Assembly Tools to be used: • Screwdriver T25 bit • Flat-head screwdriver 1. Open the light. Copyright ADB Safegate, All Rights Reserved ©...
Page 45: Replacing The Bottom Cover Assembly
Make sure you dispose the old bottom cover assembly and use the new assembly. 2. Close the light. Note Refer to the Closing a Light Fixture — connecting the Bottom Pan to the Top Cover section. UM-5056, Rev. 1.0.17, 2022/12/08 Copyright ADB Safegate, All Rights Reserved ©...
Page 46: Replacing The Secondary Cable - Sjo Cord Set
Mount the new secondary cable by torquing the new strain relief bolt at XX in-lbs XX Nm. 7. Tighten the new cable clamp bolt with the washer and lock washer at XX in-lbs XX Nm. Copyright ADB Safegate, All Rights Reserved ©...
Page 47: Replacing The Secondary Cable - Style-6 Cord Set
Make sure you dispose the old Strain Relief Bolt, the plate and the cable gland gaskets and use the new material. 5. Remove the secondary cable Make sure you dispose the old secondary cable and use the new secondary cable. UM-5056, Rev. 1.0.17, 2022/12/08 Copyright ADB Safegate, All Rights Reserved ©...
Page 48: Resetting The Fail-Open Converter
Reset / replace the fuse resistors 1. Disconnect and disassemble the light fixture. 2. Locate the fuse resistors. Note Refer to Figure 18 Figure 19 figures. Refer to Figure. Figure 18: Converter, 1-connector Copyright ADB Safegate, All Rights Reserved ©...
Page 49: Checking The Light Fixture For Water-Tightness
Execute the following procedure to test for leaks: 1. Remove the Pressure-relief Screw. Refer to the image below. Figure 20: Pressure-relief screw removal 2. Screw the pressure test fitting to the Pressure-relief Port. UM-5056, Rev. 1.0.17, 2022/12/08 Copyright ADB Safegate, All Rights Reserved ©...
Page 50 7. Depressurize and reinstall the pressure release screw (1) at 26 in-lbs (3 Nm), if the fixture is watertight. DANGER Never exceed a pressure of 22 psi (150 kPa) inside the light fixture. A higher pressure may cause injuries and damage the light. Copyright ADB Safegate, All Rights Reserved ©...
Page 52: Ordering Code L852-A/B/C/D/J/K-(L), Led Taxiway Centerline, Lead-On/Exit, Apron Lead-In (Faa)
3 = 2 x Style 6 2-pole plug, 2 individual wires 4 = 2 x Style 1 2-pole plug, jacketed SO 2-core cable. Options 0 = None 1 = Arctic Kit Version 1 = Version 1 Copyright ADB Safegate, All Rights Reserved ©...
Page 53 Only available in Digit 13 options S and M and Bi-directional configuration. Color used with L-852D(L) for medium intensity runway edge and threshold applications. L-852J&K(L) unidirectional applications only. Not ETL submitted. UM-5056, Rev. 1.0.17, 2022/12/08 Copyright ADB Safegate, All Rights Reserved ©...
Page 54: Ordering Code Led Taxiway Centerline (Icao)
5 = 1 x flat 3-pole plug, 3 individual wires 6 = 2 x flat 3-pole plug, 3 individual wires 11,13 Options 0 = None 1 = Arctic kit Version 1 = Version 1 Copyright ADB Safegate, All Rights Reserved ©...
Page 55 All Style 1 corded fixtures will include a ground lug. All Style 6 and 3-pole corded fixtures will be provided with grounding screw(s). Jacketed SO 2 core cable. Not valid option for unidirectional. UM-5056, Rev. 1.0.17, 2022/12/08 Copyright ADB Safegate, All Rights Reserved ©...
Page 56: Ordering Code Led Triple Line Taxiway Centerline Light
5 = 1 x flat 3-pole plug, 3 individual wires 6 = 2 x flat 3-pole plug, 3 individual wires Options 0 = None 1 = Arctic Kit Version Control 1 = Version 1 Copyright ADB Safegate, All Rights Reserved ©...
Page 57 All Style 1 corded fixtures will include a ground lug. All Style 6 and 3-pole corded fixtures will be provided with grounding screw(s). Only available in Digit 13 options S and M and bi-directional configuration. 8 SO cord set option is not compatible with shallow bases. UM-5056, Rev. 1.0.17, 2022/12/08 Copyright ADB Safegate, All Rights Reserved ©...
Page 58: Ordering Code Led Stopbar (Icao)
5 = 1 x flat 3-pole plug, 3 individual wires 6 = 2 x flat 3-pole plug, 3 individual wires Options 0 = None 1 = Arctic kit Version 1 = Version 1 Copyright ADB Safegate, All Rights Reserved ©...
Page 59 All Style 1 corded fixtures will include a ground lug. All Style 6 and 3-pole corded fixtures will be provided with grounding screw(s). Only available in Digit 13 options S and M and bi-directional configuration. Not valid option for unidirectional UM-5056, Rev. 1.0.17, 2022/12/08 Copyright ADB Safegate, All Rights Reserved ©...
Page 60: Ordering Code Led L-852S(L) Led Stop Bar (Faa)
Required for FAA when using AIP funds. Not ETL submitted All Style 1 corded fixtures will include a ground lug. All Style 6 and 3-pole corded fixtures will be provided with grounding screw(s). Copyright ADB Safegate, All Rights Reserved ©...
Page 61: Ordering Code Led Runway Status L-850T(L), Takeoff/ Hold, Runway Intersection (Thl/Ril) And Runway Entry Light (Rel) (Faa)
Ordering Code Notes All Style 1 corded fixtures will include a ground lug. All Style 6 and 3-pole corded fixtures will be provided with grounding screw(s). Not ETL submitted UM-5056, Rev. 1.0.17, 2022/12/08 Copyright ADB Safegate, All Rights Reserved ©...
Page 63: Spare Parts
Spare parts are available for inset light fixtures with and without the control and monitoring functionality. For more information, see http://www.adbsafegate.com/ and the spare part lists, or contact ADB SAFEGATE for assistance. 7.1 Versions and Exploded View Versions, 8-inch and 12-inch Insets Figure 21: Taxiway Insets, cord set options Taxiway Inset 8"...
Page 64: Figure 22: 8-Inch (Left) And 12 Inch(Right)
Light Engine Assembly, 8-inch and 12-inch, with Arctic Kit SP.AS00137-XXX Bottom Pan Assembly, 8-inch and 12-inch SP.AS00021-XXX Note Full assembly numbers are listed in the spare part tables per application, starting from page 60 in the user manual. Copyright ADB Safegate, All Rights Reserved ©...
Page 65: Spare Part Illustrations
8 - inch & 12 inch for Taxiway applications only 8 - inch compatible with both 8 - inch and gaskets are used 12 - inch top covers UM-5056, Rev. 1.0.17, 2022/12/08 Copyright ADB Safegate, All Rights Reserved ©...
Page 66: Figure 27: Led Light Engines Wire Harness, Package Of 10
Figure 30: Ground lugs, package of 5 Taxiway replacement prism (package of pcs.), available options Standard Reinforced (Sapphire coated) Figure 31: Style-1 Cord Set Cable Clamp, package of 5 Figure 32: Mounting screws, package of 100 Copyright ADB Safegate, All Rights Reserved ©...
Page 67: Figure 33: Pressure Release Screws, Package Of 5
Figure 33: Pressure release screws, package of 5 Note Pressure release screw O-ring is to be replaced with new O-ring prior to re-installation of the pressure relief screw. UM-5056, Rev. 1.0.17, 2022/12/08 Copyright ADB Safegate, All Rights Reserved ©...
Page 68: Spare Parts - Taxiway Centerline Light Faa
1 curved, standard prism SP.AS00136-C1S unidirectional side 1 curved, reinforced prism SP.AS00136-C1R unidirectional side 2 curved, standard prism SP.AS00136-C2S unidirectional side 2 curved, reinforced prism SP.AS00136-C2R bidirectional, straight, standard prism SP.AS00136-SBS Copyright ADB Safegate, All Rights Reserved ©...
Page 69 L-852D(L), non-monitored (S-non-BAP) or monitored (M) 1 or 2 SP.AS00137-DWW-F yellow for L-852D(L), non-monitored (S-non-BAP) or monitored (M) 1 or 2 SP.AS00137-DYY-F F-green curved for L-852K(L), non-monitored (S-non-BAP) or monitored 1 or 2 SP.AS00137-CFN-F UM-5056, Rev. 1.0.17, 2022/12/08 Copyright ADB Safegate, All Rights Reserved ©...
Page 70 SP.73A0194/1 Cord set, L-823 style 6, 8" & 12" bottom pan 1 or 2 SP.SGE96253351 Cable retaining clamp, for use with style 1 cord set 1 or 2 SP.MB00003-013-01 Ground lug kit SP.72A0401 Copyright ADB Safegate, All Rights Reserved ©...
Page 71 All screws for fastening are included. Component availability or design may be subject to change due to unforeseen circumstances. This document is subject to change or new information from ADB SAFEGATE, as and when available or if required, with reservation for error or price changes.
Page 72: Spare Parts - Taxiway Centerline Light Icao
F-green enhanced taxiway centreline for rapid exit 1 or 2 SP.AS00089-WFF-TR yellow wide 1 or 2 SP.AS00089-WYN-TW yellow enhanced taxiway centreline for rapid exit 1 or 2 SP.AS00089-WYY-TR F-green curved 1 or 2 SP.AS00089-CFN Copyright ADB Safegate, All Rights Reserved ©...
Page 73 1 SJO jacketed cord set SP.AS00021-M1J monitored converter, 2-con style 6 cord sets SP.AS00021-M23 monitored converter, 2-con 3-pole cord sets SP.AS00021-M2F monitored converter, 2-con style 1 SJO jacketed cord sets SP.AS00021-M2J UM-5056, Rev. 1.0.17, 2022/12/08 Copyright ADB Safegate, All Rights Reserved ©...
Page 74 All screws for fastening are included. Component availability or design may be subject to change due to unforeseen circumstances. This document is subject to change or new information from ADB SAFEGATE, as and when available or if required, with reservation for error or price changes.
Page 75: Spare Parts - Stop Bar Light Faa
1 SJO jacketed cord set SP.AS00021-L1J monitored converter, style 6 cord set SP.AS00021-M13 monitored converter, style 1 SJO jacketed cord set SP.AS00021-M1J EQ converter, style 6 cord set SP.AS00021-R13 UM-5056, Rev. 1.0.17, 2022/12/08 Copyright ADB Safegate, All Rights Reserved ©...
Page 76 All screws for fastening are included. Component availability or design may be subject to change due to unforeseen circumstances. This document is subject to change or new information from ADB SAFEGATE, as and when available or if required, with reservation for error or price changes.
Page 77: Spare Parts - Stop Bar Light Icao
2 curved, standard prism SP.AS00136-C2S unidirectional side 2 curved, reinforced prism SP.AS00136-C2R bidirectional, straight, standard prism SP.AS00136-SBS bidirectional, straight, reinforced prism SP.AS00136-SBR bidirectional curved, standard prism SP.AS00136-CBS bidirectional curved, reinforced prism SP.AS00136-CBR UM-5056, Rev. 1.0.17, 2022/12/08 Copyright ADB Safegate, All Rights Reserved ©...
Page 78 SP.AS00021-M2F monitored converter, 2-con style 1 SJO jacketed cord sets SP.AS00021-M2J EQ converter, style 6 cord set SP.AS00021-R13 EQ converter, 3-pole cord set SP.AS00021-R1F EQ converter, style 1 SJO jacketed cord set SP.AS00021-R1J Copyright ADB Safegate, All Rights Reserved ©...
Page 79 All screws for fastening are included. Component availability or design may be subject to change due to unforeseen circumstances. This document is subject to change or new information from ADB SAFEGATE, as and when available or if required, with reservation for error or price changes.
Page 80: Spare Parts - Taxiway Status, Takeoff/ Hold, Intersection And Entry Light
6 cord set SP.AS00021-M13 monitored converter, style 1 SJO jacketed cord set SP.AS00021-M1J EQ converter, style 6 cord set SP.AS00021-R13 EQ converter, style 1 SJO jacketed cord set SP.AS00021-R1R Copyright ADB Safegate, All Rights Reserved ©...
Page 81 All screws for fastening are included. Component availability or design may be subject to change due to unforeseen circumstances. This document is subject to change or new information from ADB SAFEGATE, as and when available or if required, with reservation for error or price changes.
Page 82: Spare Parts - Triple Line Taxiway Centerline Light
AXON Taxiway Inset Lights, 8-inch and 12-inch Spare Parts 7.8 Spare Parts — Triple Line Taxiway Centerline Light Copyright ADB Safegate, All Rights Reserved ©...
Page 83: Winter Operations: Snow Plowing Guidelines For Inset Lights
Lights Introduction Most ADB Safegate light fixtures are low protrusion height and the risk to damage the light is less than with fixtures that protrude higher above ground. Reinforced prisms are optional available for certain fixtures, further increasing the scratch resistance for enhanced lifetime.
Page 84: Figure 34: Fig. 1 - Snowplow Blade With Well Aligned Segments
The plastic cutting edges should be replaced when worn down to the wear limit marking. Wear down to the metal portion of the plow should be avoided in any case. Figure 35: Fig. 2 — Snowplow blade with wear and steps between segments Copyright ADB Safegate, All Rights Reserved ©...
Page 85 Do not use guidance and support wheels that are made of steel. • Any protruding bolts and metal elements whose clearance to pavement is less than 20 mm during operation shall be avoided UM-5056, Rev. 1.0.17, 2022/12/08 Copyright ADB Safegate, All Rights Reserved ©...
Page 86 The use of sapphire prisms will not make the prisms scratch proof as scratches can still occur over time but it will increase the service interval and service life of the prism. Copyright ADB Safegate, All Rights Reserved ©...
Page 87 21 Nm + • ADB 12‑in Eurobase Metric screw kit Self-locking nut kit SP.013114/10pc Loctite 2701 or 638 Loctite 2701 or 638 12‑in M10×22 mm 12‑in M10 H=100 SP.013115/100pc UM-5056, Rev. 1.0.17, 2022/12/08 Copyright ADB Safegate, All Rights Reserved ©...
Page 88: Interoperability
You need to know what base the light fixture will be installed in, in order to choose the correct gasket, bolts and nuts. Failure to follow these cautions can result in equipment damage or aircraft FOD. Copyright ADB Safegate, All Rights Reserved ©...
Page 91: Power Table
Taxiway Centerline Wide, 13.1 VA 13.1 VA 15 W 15 W 7.7 VA 7.7 VA 20.8 VA 20.8 VA bidirectional Notes Values provided are for the "S" option non-monitored power only. UM-5056, Rev. 1.0.17, 2022/12/08 Copyright ADB Safegate, All Rights Reserved ©...
Page 93: Cable Loss
For a primary cable of e.g., 100 m of 6 mm CU-wire, 100 m × 0.12 W/m = 12 W equals the additional loss to be taken into account. UM-5056, Rev. 1.0.17, 2022/12/08 Copyright ADB Safegate, All Rights Reserved ©...
Page 95: Support
E.2.1 Local Authority Recycling The disposal of ADB SAFEGATE products is to be made at an applicable collection point for the recycling of electrical and electronic equipment. The correct disposal of equipment prevents any potential negative consequences for the environment and human health, which could otherwise be caused by inappropriate waste handling.
Page 96: Adb Safegate Recycling
Main Unit Serial Number. ADB SAFEGATE will continue to monitor and update according for any future requirements for EU directives as and when EU member states implement new regulations and or amendments. It is our aim to maintain our compliance plan and assist our customers.
Page 97 Tel.: +46 (0)40 699 17 00 Internet: www.adbsafegate.com Fax: +46 (0)40 699 17 30 ADB SAFEGATE, China ADB SAFEGATE Airfield Technologies Ltd. China Unit 603, D Block, CAMIC International Convention Center, No 3, Hua Jia Di East road, ChaoYang district, Beijing 100102 P.R.

This manual is also suitable for:

Axon faa l-852a Axon faa l-852bl Axon faa l-852b Axon faa l-852c Axon faa l-852cl Axon faa l-852d ... Show all

ADB Safegate AXON FAA L-852AL User Manual

Quick Links

Need help?

Questions and answers

Related Manuals for ADB Safegate AXON FAA L-852AL

Summary of Contents for ADB Safegate AXON FAA L-852AL

This manual is also suitable for:

Table of Contents