ADB Safegate AXON User Manual
  1. Manuals
  2. Brands
  3. ADB Safegate Manuals
  4. Lighting Equipment
  5. AXON
  6. User manual

ADB Safegate AXON User Manual

Runway inset lights 12-inch and 8-inch (rc-rz-re-rn-rt-rs-ts-r6-sw-s6-rw)
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
AXON Runway Inset Lights
12-inch and 8-inch (RC-RZ-RE-RN-RT-RS-TS-R6-SW-S6-RW)
User Manual
UM-5055, Rev. 1.0.9, 2022/04/29

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the AXON and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for ADB Safegate AXON

Summary of Contents for ADB Safegate AXON

  • Page 1 AXON Runway Inset Lights 12-inch and 8-inch (RC-RZ-RE-RN-RT-RS-TS-R6-SW-S6-RW) User Manual UM-5055, Rev. 1.0.9, 2022/04/29...
  • Page 3 Material Handling Precautions and Storage precautions that must be followed. ADB SAFEGATE reserves the right to examine goods upon which a claim is made. Said goods must be presented in the same condition as when the defect therein was discovered. ADB SAFEGATE furthers reserves the right to require the return of such goods to establish any claim.
  • Page 4 This manual could contain technical inaccuracies or typographical errors. ADB SAFEGATE BV reserves the right to revise this manual from time to time in the contents thereof without obligation of ADB SAFEGATE BV to notify any person of such revision or change. Details and values given in this manual are average values and have been compiled with care. They are not binding, however, and ADB SAFEGATE BV disclaims any liability for damages or detriments suffered as a result of reliance on the information given herein or the use of products, processes or equipment to which this manual refers.

  • Page 5: Table Of Contents

    6.9 Ordering Code LED Stopway (SW , ≤ 45 m Width) ........................... 60 6.10 Ordering Code LED Runway Status L-850T(L), Takeoff/ Hold, Runway Intersection (THL/RIL) and Runway Entry Light (REL) (RS-TS FAA) ........................................ 61 UM-5055, Rev. 1.0.9, 2022/04/29 Copyright ADB Safegate, All Rights Reserved ©...
  • Page 6 7.0 INTEROPERABILITY ................................65 8.0 POWER TABLE ..................................69 9.0 CABLE LOSS ................................... 73 10.0 SUPPORT ..................................... 75 10.1 ADB SAFEGATE Website ....................................75 10.2 Recycling ..........................................75 10.2.1 Local Authority Recycling ..................................75 10.2.2 ADB SAFEGATE Recycling ..................................76...
  • Page 7 Figure 15: Runway Inset, 8 inch, with Style 6 cord set .............................. 42 Figure 16: Exploded View, 8-inch fixtures — Part 1 ..............................43 Figure 17: Exploded View, 8-inch fixtures — Part 2 ..............................44 UM-5055, Rev. 1.0.9, 2022/04/29 Copyright ADB Safegate, All Rights Reserved ©...
  • Page 8 AXON Runway Inset Lights List of Figures viii Copyright ADB Safegate, All Rights Reserved ©...
  • Page 9 Table 8: Converter options — Bottom Pan Assembly, 8 inch ..........................45 Table 9: Interoperability matrix — 12 inch ..................................66 Table 10: Interoperability matrix — 8 inch ..................................66 UM-5055, Rev. 1.0.9, 2022/04/29 Copyright ADB Safegate, All Rights Reserved ©...
  • Page 10 AXON Runway Inset Lights List of Tables Copyright ADB Safegate, All Rights Reserved ©...

  • Page 11: Safety

    1.0 Safety Introduction to Safety This section contains general safety instructions for installing and using ADB SAFEGATE equipment. Some safety instructions may not apply to the equipment in this manual. Task- and equipment-specific warnings are included in other sections of this manual where appropriate.

  • Page 12: Introduction To Safety

    AXON Runway Inset Lights Safety 1.1.1 Introduction to Safety CAUTION Unsafe Equipment Use This equipment may contain electrostatic devices, hazardous voltages and sharp edges on components • Read installation instructions in their entirety before starting installation. • Become familiar with the general safety instructions in this section of the manual before installing, operating, maintaining or repairing this equipment.

  • Page 13: Material Handling Precautions: Storage

    Allow only qualified personnel to make repairs. Repair or replace the malfunctioning component according to instructions provided in its manual. Failure to follow these instructions can result in death or equipment damage UM-5055, Rev. 1.0.9, 2022/04/29 Copyright ADB Safegate, All Rights Reserved ©...

  • Page 14: Material Handling Precautions: Fasteners

    Note To minimize the risk of errors, the ADB SAFEGATE Sales Representative will have information on which gasket goes with which base. This information is also provided in the product Data sheets, the User Manuals and the Spare Part Lists.

  • Page 15: About This Manual

    2.0 About this Manual This document includes AXON runway inset light fixture information with a focus on safety, installation and maintenance procedures. For more information, see www.adbsafegate.com. Note It is very important to read this document before any work is started.
  • Page 16 AXON Runway Inset Lights About this Manual Copyright ADB Safegate, All Rights Reserved ©...

  • Page 17: Introduction

    Fixture with integrated ILCMS remote utilizing orthogonal frequency-division multiplexing (OFDM) technology providing superior communication interfacing with LINC 360 System. NOTICE All our Axon R-series light fixtures are equipped with failed LED detection monitoring as required by FAA Engineering Brief 67. Runway Inset 8" with Style-1 jacketed cord set Runway Inset 12"...

  • Page 18: Product Information

    AXON Runway Inset Lights Introduction 3.1 Product Information Compliance and Standards RN-RT RN-RT Compliance Description Application: RC-RZ RE 45 m R6 60 m ICAO Reference DS-XXXX: 5040 5041 5096 5043 5044 5045 AC 150/5345-46 and the FAA Engineering Brief No. 67...
  • Page 19 ICAO and MOS • Stopway Uses RS-TS FAA FAA Runway Status Light (RWSL) Applications • L-850T(L) THL Runway Takeoff/Hold Light • L-850T(L) RIL Runway Intersection Light • REL Runway Entry Light UM-5055, Rev. 1.0.9, 2022/04/29 Copyright ADB Safegate, All Rights Reserved ©...
  • Page 20 AXON Runway Inset Lights Introduction Uses RS-TS ICAO FAA Runway Status Light (RWSL) Applications • L-850T(L) THL Runway Takeoff/Hold Light • L-850T(L) RIL Runway Intersection Light • REL Runway Entrance Light Uses RW ICAO ICAO • Runway Threshold Wingbar Uses S6 60 m ICAO •...
  • Page 21 Fully dimmable lights, conforming to the dimming curve of traditional halogen lights • Low protrusion, high-intensity, Style 3 (≤ 6.35 mm) inset light fixtures • No negative slope in front of the prisms UM-5055, Rev. 1.0.9, 2022/04/29 Copyright ADB Safegate, All Rights Reserved ©...
  • Page 22 AXON Runway Inset Lights Introduction Sustainability • Fully encapsulated all-in-one universal power supplies for Runway, Taxiway, Approach and Omni inset families • Latest generation LEDs providing a long-lasting light source with high efficiency and low power consumption • Reinforced top cover substantially exceeding standards to improve durability and longevity •...

  • Page 23: Dimensions And Weight

    FAA – RG – SB FAA – SB ICAO RC – RZ – RS-TS – RG – SB FAA – SB ICAO 3 kg / 6.6 lb (8 in) 203 mm / 8 in UM-5055, Rev. 1.0.9, 2022/04/29 Copyright ADB Safegate, All Rights Reserved ©...
  • Page 24 AXON Runway Inset Lights Introduction Copyright ADB Safegate, All Rights Reserved ©...

  • Page 25: Installation

    If the inset light fixture is to be installed on another type of base or adapter ring not provided by ADB SAFEGATE, contact ADB SAFEGATE. The inset light fixture is fixed in the base by six M10 lock nuts or by six M10×25 or M10×22 bolts dependent on base installation.

  • Page 26: Installation And Removal Of The 12-Inch Light Fixture

    AXON Runway Inset Lights Installation 4.3 Installation and Removal of the 12-inch Light Fixture Install the light fixture in a base 1. Carefully clean all contact surfaces of the light fixture and the base. 2. Put the O-ring gasket in the gasket track on the base.

  • Page 27: Toe-In

    Both sides toed-in 3.5° Optical L-850D(L) - Runway threshold/end (RT)L-852C(L) - Taxiway Centreline Narrow Green straight or 3.5° toed-in. Red is straight Optical (TC-I) L-850D(L) - Runway end (RN) Straight UM-5055, Rev. 1.0.9, 2022/04/29 Copyright ADB Safegate, All Rights Reserved ©...

  • Page 28: Light Emission Directions

    AXON Runway Inset Lights Installation 4.5 Light Emission Directions 4.5.1 Definition of Light Emission Directions Light fixtures that have a toe-in are marked with an arrow to ensure a correct installation with regard towards the toe-in. The light fixtures should be installed with the arrow pointing towards the centerline.

  • Page 29: Maintenance

    Spare parts are available, if required. For more information, see www.adbsafegate.com and the Spare Parts List document, or contact ADB SAFEGATE for assistance. CAUTION Use of incorrect combination of gaskets, bolts and nuts can create severe damages to the product installation and create multiple safety risks.

  • Page 30: Winter Operations: Snow Plowing Guidelines For Inset Lights

    5.1.1 Winter Operations: Snow Plowing Guidelines for inset Lights Introduction Most ADB Safegate light fixtures are low protrusion height and the risk to damage the light is less than with fixtures that protrude higher above ground. Reinforced prisms are optional available for certain fixtures, further increasing the scratch resistance for enhanced lifetime.
  • Page 31 The most effective counter-measures in case of damages to in-pavement lights are to slightly increase the plow blade/cutting edge height above ground and reduction of snowplow speed. Snowplows Material and Structure of the Cutting Edge UM-5055, Rev. 1.0.9, 2022/04/29 Copyright ADB Safegate, All Rights Reserved ©...

  • Page 32: Figure 3: Fig. 1 - Snowplow Blade With Well Aligned Segments

    AXON Runway Inset Lights Maintenance To protect in-pavement lights from damage during the snow removal it is important that the snowplows are equipped with plastic cutting edges. • The plastic cutting edge should be made of polyurethane, rubber or material of similar consistence and characteristics.

  • Page 33: Figure 5: Fig. 3 - Snowplow Blade Without Clearance

    Do not use guidance and support wheels that are made of steel. • Any protruding bolts and metal elements whose clearance to pavement is less than 20 mm during operation shall be avoided Speed and angle of the plow UM-5055, Rev. 1.0.9, 2022/04/29 Copyright ADB Safegate, All Rights Reserved ©...

  • Page 34: Recommended Maintenance Program For Optimal Service Life

    AXON Runway Inset Lights Maintenance High snowplow speeds can damage the light outlets and prisms could eventually break. The allowable speed should be determined before start of operation, based on the configuration of the equipment. • A speed of greater 40 km per hour is not advised.
  • Page 35 Green – Areas outside Red and Amber areas It is recommended that there is a reliable means of recording the location history of fittings (similar to ADB Safegate ALIS) to ensure that the maximum duration in critical areas (RED) of the runway are not exceeded.

  • Page 36: Recommendation

    AXON Runway Inset Lights Maintenance 5.2.1 Recommendation Based on the air traffic volume and location on the airfield, a matrix was created for recommended inspection intervals. Visual inspection: Visually inspect the light fixture and make sure that • Prism is clean and no cracks are visible •...
  • Page 37 Talk to your local sales representative if you have any questions or would require some assistance to go through local conditions and see how we can help establish a well-defined maintenance planning to optimize the expected service life of your investment. UM-5055, Rev. 1.0.9, 2022/04/29 Copyright ADB Safegate, All Rights Reserved ©...

  • Page 38: Workshop Maintenance

    AXON Runway Inset Lights Maintenance 5.3 Workshop Maintenance CAUTION Before you start, make sure you have read and understand Safety instructions. The following standard tools and accessories are required for maintenance of the unit: • One angled socket spanner of 16 or 17 mm •...

  • Page 39: Close A Light Fixture - Connect The Bottom Pan To The Top Cover

    2. Remove the LED brackets (3 pieces M5 screws per bracket) to access the connector of the LED wire. Make sure you dispose the old screws and use new screws. UM-5055, Rev. 1.0.9, 2022/04/29 Copyright ADB Safegate, All Rights Reserved ©...

  • Page 40: Replace The Light Engine Assembly

    AXON Runway Inset Lights Maintenance 3. Disconnect the old wire harnesses. Make sure you dispose the old wire harnesses and use new wire harnesses. 4. Connect the new wire harnesses. 5. Mount the LED bracket with new screws at 26 in-lbs (3 Nm).

  • Page 41: Replace The Top Cover Assembly

    Flat-head screwdriver 1. Open the light. Note Refer to the Open and close a 12‑inch Fixture section. 2. Remove the Light Engine(s) (4 pieces M4 screws per light engine assembly. UM-5055, Rev. 1.0.9, 2022/04/29 Copyright ADB Safegate, All Rights Reserved ©...

  • Page 42: Replace The Bottom Cover Assembly

    AXON Runway Inset Lights Maintenance image Make sure you dispose the old screws and the old top cover and use the new material. 3. Replace the old top cover with new top cover assembly. 4. Mount the light engine(s) into the new top cover assembly.

  • Page 43: Replace The Secondary Cable - Sjo Cord Set

    5.3.9 Replace the secondary Cable — Style-6 cord set Tools to be used: • Screwdriver T25 bit • Flat-head screwdriver • Small flat head screwdriver 1. Open the light. UM-5055, Rev. 1.0.9, 2022/04/29 Copyright ADB Safegate, All Rights Reserved ©...

  • Page 44: Reset The Fail-Open Converter

    AXON Runway Inset Lights Maintenance Note Refer to the Open and close a 12‑inch Fixture section. 2. Disconnect the cable: a) Disconnect the secondary cable from the converter by placing a small flat-head screwdriver into the opening located at the other side of the secondary wire, and b) Release the cable by prying the screwdriver on the cable release opening.

  • Page 45: Check The Light Fixture For Water-Tightness

    5.3.11 Check the Light Fixture for Water-tightness Tools to be used: • Flat head screwdriver Execute the following procedure to test for leaks: 1. Remove the Pressure-relief Screw. Refer to the image below. UM-5055, Rev. 1.0.9, 2022/04/29 Copyright ADB Safegate, All Rights Reserved ©...
  • Page 46 AXON Runway Inset Lights Maintenance 2. Screw the pressure test fitting to the Pressure-relief Port. NOTICE The Pressure-relief Port is the opening you created when the pressure relief screw was removed. 3. Screw the fitting hand-tight. 4. Pressurize to 20 psi (130 kPa).

  • Page 47: Spare Parts

    Spare parts are available for inset light fixtures with and without the control and monitoring functionality. For more information, see www.adbsafegate.com and the spare part lists, or contact ADB SAFEGATE for assistance. 6.1 Versions and Exploded View Versions, 12-inch Insets...

  • Page 48: Figure 12: Exploded View, 12-Inch Fixtures - Part 1

    AXON Runway Inset Lights Spare Parts Exploded View, 12-inch Insets Figure 12: Exploded View, 12-inch fixtures — Part 1 Table 1: Exploded View Legend — Top Cover Assembly, 12 inch Call-out Description Part Number Top Cover Assembly AS-00018-XXX-02 Light Engine Assembly...

  • Page 49: Figure 13: Exploded View, 12-Inch Fixtures - Part 2

    M4x7 x 10 90 FLAT A2 6 PAN LP DIN 7985 MFPM4LT-710-01 Cable Gasket, silicone MS00016-000-01 Cord-Retaining Disc XXXXXX (See Table L = I M4x7 x 10 90 FLAT A2 6 PAN LP DIN 7985 MFPM4LT-710-01 UM-5055, Rev. 1.0.9, 2022/04/29 Copyright ADB Safegate, All Rights Reserved ©...

  • Page 50: Table 3: Cord Set Options - Bottom Pan Assembly, 12 Inch

    AXON Runway Inset Lights Spare Parts Table 2: Exploded View Legend — Bottom Pan Assembly, 12 inch (Continued) Call-out Description Part Number Cordset XXXXX (See Table Power Converter EP000X-XXX-XX (See Table Bottom Pan MC00005-XXX-03 Table 3: Cord set options — Bottom Pan Assembly, 12 inch...
  • Page 51 Window B = Bidirectional (1+1) U = Unidirectional (1+0) Heater N = No Arctic kit A = With Arctic kit Prism G = Standard glass S = Reinforced (Sapphire) UM-5055, Rev. 1.0.9, 2022/04/29 Copyright ADB Safegate, All Rights Reserved ©...

  • Page 52: Figure 14: Runway Inset, 8 Inch, With Style 1 Jacketed Cord Set

    AXON Runway Inset Lights Spare Parts Versions, 8-inch Insets Figure 14: Runway Inset, 8 inch, with Style 1 jacketed cord set Figure 15: Runway Inset, 8 inch, with Style 6 cord set Copyright ADB Safegate, All Rights Reserved ©...

  • Page 53: Figure 16: Exploded View, 8-Inch Fixtures - Part 1

    M4x7 x10 PAN A2 6 LOBE LP DIN 7985 MFPM4LT-708-01M Pressure Release Screw + O-ring, silicone, size 008, 1/16 W x3/16 ID MF00090-000-01 + M S00001-008-01 Power Supply to Light Engine E W00079-000-01 UM-5055, Rev. 1.0.9, 2022/04/29 Copyright ADB Safegate, All Rights Reserved ©...

  • Page 54: Figure 17: Exploded View, 8-Inch Fixtures - Part 2

    AXON Runway Inset Lights Spare Parts Exploded View, 8-inch Insets Figure 17: Exploded View, 8-inch fixtures — Part 2 Table 6: Exploded View Legend — Bottom Pan Assembly, 8 inch Call-out Description Part Number M4x7 x 10 90 FLAT A2 6 LOBE LP DIN 7985...

  • Page 55: Table 7: Cord Set Options - Bottom Pan Assembly, 8 Inch

    AS00021- EP00017-000-02 FAIL-OPEN MON - 1 CON M1X-01 AS00021- EP00016-000-01 FAIL-OPEN MON - 2 CON M2X-01 AS00021- EP00028-000-01 Non-MON (US) 1 CON R1X-01 AS00021- EP00028-001-01 EQ 1 CON S1X-01 UM-5055, Rev. 1.0.9, 2022/04/29 Copyright ADB Safegate, All Rights Reserved ©...
  • Page 56 AXON Runway Inset Lights Spare Parts Ordering Code, 8-inch insets Bottom Cover Power L = Low power converter M = Fail-open P = IQ power disabled (HPC) R = EQ S = Non-MON Cord set quantity 1 = 1 connector...

  • Page 57: Ordering Code Led L-850A(L), L-850B(L) Runway Centerline And Touch Down Zone (Rc-Rz)

      6,10 6 = 2 x Flat 3-pole plug, 3 individual wires   8,10 Options 0 = None   1 = Arctic Kit   Version 1 = Version 1 UM-5055, Rev. 1.0.9, 2022/04/29 Copyright ADB Safegate, All Rights Reserved ©...
  • Page 58 AXON Runway Inset Lights Spare Parts Ordering Code Notes EQ light fixtures are only available as a one connector option. Includes standards NATO, EASA, STAC, CAP 168, TP 312 and MOS 139. Required for FAA when using AIP funds. If a 2-cord set fixture is required meeting BAP, Digit 13, "Power and Monitoring", must be M.

  • Page 59: Ordering Code Led L-850C(L) Runway Edge (Re 45 M)

    5 = 1 x Flat 3-pole plug, 3 individual wires   6 = 2 x Flat 3-pole plug, 3 individual wires   Options 0 = None 1 = Arctic Kit   Version 1 = Version 1 UM-5055, Rev. 1.0.9, 2022/04/29 Copyright ADB Safegate, All Rights Reserved ©...
  • Page 60 AXON Runway Inset Lights Spare Parts Ordering Code Notes Fixture supports: Compatible with both shallow and deep 12-inch bases. EQ light fixtures are only available as a one connector option. Includes standards NATO, EASA, STAC, CAP 168, TP 312 and MOS 139.

  • Page 61: Ordering Code Led Runway Edge, ≤ 60 M Width (Re 60 M)

    5 = 1 x flat 3-pole plug, 3 individual wires   6 = 2 x flat 3-pole plug, 3 individual wires   Options 0 = None   1 = Arctic Kit   Version Control 1 = Version 1 UM-5055, Rev. 1.0.9, 2022/04/29 Copyright ADB Safegate, All Rights Reserved ©...
  • Page 62 AXON Runway Inset Lights Spare Parts Ordering Code Notes Includes NATO, EASA, STAC, TP-312, MOS 139 If 2-cord set fixture, digit 13 must be M Bidirectional application - Place the required color option in Side 1 (Left) and 2 (Right). Left and right side determined by viewing fixture from runway centerline.

  • Page 63: Ordering Code Led L-852G(L) Runway Guard Light (Rg)

    Fixture supports: Compatible with both shallow and deep 12-inch bases. EQ light fixtures are only available as a one connector option. Option 3 covers standards: NATO,EASA,STAC,TP-312,MOS 139. 50-Hz applications FAA applications UM-5055, Rev. 1.0.9, 2022/04/29 Copyright ADB Safegate, All Rights Reserved ©...
  • Page 64 AXON Runway Inset Lights Spare Parts All Style 1 corded fixtures will include a ground lug. All Style 6 or 3-pole corded fixtures will be provided without a ground lug UNLESS digit 6 is option 1 "BAP". Copyright ADB Safegate, All Rights Reserved...

  • Page 65: Ordering Code Led Runway Threshold, End And Threshold/End (Rn-Rt Faa)

    4 = 2 x Style 1 2-pole plug, jacketed SO 2 core cable   4,5,6,8 Options 0 = None   1 = Arctic Kit   Version 1 = Version 1 UM-5055, Rev. 1.0.9, 2022/04/29 Copyright ADB Safegate, All Rights Reserved ©...
  • Page 66 AXON Runway Inset Lights Spare Parts Ordering Code Notes Fixture supports: Compatible with both shallow and deep 12-inch bases. EQ light fixtures are only available as a one connector option. Required when FAA AIP funded If a 2-cord set fixture is required meeting BAP, digit 13, "Power and Monitoring", must be M.

  • Page 67: Ordering Code Led Runway, Threshold/End And End (Rn-Rt Icao)

    5 = 1 x flat 3-pole plug, 3 individual wires   6 = 2 x flat 3-pole plug, 3 individual wires   Options 0 = None 1 = Arctic Kit   Version Control 1 = Version 1 UM-5055, Rev. 1.0.9, 2022/04/29 Copyright ADB Safegate, All Rights Reserved ©...
  • Page 68 AXON Runway Inset Lights Spare Parts Ordering Code Notes Fixture supports: Compatible with both shallow and deep 12-inch bases. EQ light fixtures are only available as a one connector option. Option 3 covers standards: NATO,EASA,STAC,TP-312,MOS 139. L and R designations are always in relationship to Side 1 only.

  • Page 69: Ordering Code Led L-850E(L) Threshold (Rr)

    1 = Version 1 Ordering Code Notes Provided with ground lug Required for NAVAIR Green only For White and Red Digit 5 must be 4. Digit 5 must be 2. UM-5055, Rev. 1.0.9, 2022/04/29 Copyright ADB Safegate, All Rights Reserved ©...

  • Page 70: Ordering Code Led Stopway (Sw , ≤ 45 M Width)

    AXON Runway Inset Lights Spare Parts 6.9 Ordering Code LED Stopway (SW , ≤ 45 m Width) Ordering Code Application SW = Stopway 45 m Standards 3 = ICAO Market Specific 0 = None Dimensions 2 = 12 inch (305 mm) diameter, 11.25 inch...

  • Page 71: Ordering Code Led Runway Status L-850T(L), Takeoff/ Hold, Runway Intersection (Thl/Ril) And Runway Entry Light (Rel) (Rs-Ts Faa)

    2 = 1 x Style 1 2-pole plug, jacketed SO 2 Core Cable Options 0 = None 1 = Arctic Kit Version Control 1 = Version 1 Ordering Code Notes Not ETL submitted UM-5055, Rev. 1.0.9, 2022/04/29 Copyright ADB Safegate, All Rights Reserved ©...

  • Page 72: Ordering Code Led Runway Status L-850T(L), Takeoff/ Hold, Runway Intersection (Thl/Ril) And Runway Entry Light (Rel) (Rs-Ts Icao)

    AXON Runway Inset Lights Spare Parts 6.11 Ordering Code LED Runway Status L-850T(L), Takeoff/ Hold, Runway Intersection (THL/RIL) and Runway Entry Light (REL) (RS-TS ICAO) Ordering Code Application RS = Runway Status; Takeoff/ Hold (THL); L-850T(L) ( RIL); Runway Intersection TS = Runway Status;...

  • Page 73: Ordering Code Led Runway Threshold Wingbar (Rw Icao)

    L and R designations are always in relationship to Side 1 only. All Style 1 corded fixtures will include a ground lug. All Style 6 or 3-pole corded fixtures will be provided without a ground lug. UM-5055, Rev. 1.0.9, 2022/04/29 Copyright ADB Safegate, All Rights Reserved ©...

  • Page 74: Ordering Code Led Stopway (S6 ≤ 60 M Width)

    AXON Runway Inset Lights Spare Parts 6.13 Ordering Code LED Stopway (S6 ≤ 60 m Width) Ordering Code Application S6 = Stopway 60 m Standards 3 = ICAO Market Specific 0 = None Dimensions 2 = 12 inch (305 mm) diameter, 11.25 inch...

  • Page 75: Interoperability

    7.0 INTEROPERABILITY Base installation – O-ring selection and retaining bolts 12-inch For 12‑inch light fixtures the O-ring is required. Refer to data sheet for ordering code for corresponding 12‑inch base. UM-5055, Rev. 1.0.9, 2022/04/29 Copyright ADB Safegate, All Rights Reserved ©...

  • Page 76: Table 9: Interoperability Matrix - 12 Inch

    AXON Runway Inset Lights INTEROPERABILITY CAUTION Use of incorrect combination of gaskets, bolts and nuts can create severe damages to the product installation and create multiple safety risks. To obtain a safe and watertight installation the O‑ring and retaining bolt stated in the document must be used.
  • Page 77 35 Nm + Loctite 638 Thorn/ID SGE.SP24523/10 pc Metric screw kit Self-locking 8-in–12-in SGE.SP24526/100 pc 25 mm nut kit H100 IDM 6494 Base 8”-13X- Base MK2 8” Base 8”-13X- ERNI EE08 Eurobase UM-5055, Rev. 1.0.9, 2022/04/29 Copyright ADB Safegate, All Rights Reserved ©...
  • Page 78 AXON Runway Inset Lights INTEROPERABILITY Copyright ADB Safegate, All Rights Reserved ©...

  • Page 79: Power Table

    65 W 15.5 VA 87.4 VA Runway Edge, L-850C(L), bidirectional, Red/Yellow 69.7 VA 65 W 15.6 VA 85.3 VA Notes Values provided are for the "S" option non-monitored power only. UM-5055, Rev. 1.0.9, 2022/04/29 Copyright ADB Safegate, All Rights Reserved ©...
  • Page 80 AXON Runway Inset Lights POWER TABLE L-850D(L) LED Runway Threshold, End, Threshold/End (RN-RT FAA), without Arctic Kit Isolation transformer Fixture type – 1 cord set Fixture load CCR load Wattage Load Runway Threshold, L-850D(L), bidirectional, F- 36.6 VA 45 W 14.1 VA...
  • Page 81 Fixture load CCR load Wattage Load Stopbar, L-852S(L), unidirectional, Red 17.5 VA 25 W 9.8 VA 27.3 VA Notes Values provided are for the "S" option non-monitored power only. UM-5055, Rev. 1.0.9, 2022/04/29 Copyright ADB Safegate, All Rights Reserved ©...
  • Page 82 AXON Runway Inset Lights POWER TABLE Copyright ADB Safegate, All Rights Reserved ©...

  • Page 83: Cable Loss

    For a primary cable of e.g., 100 m of 6 mm CU-wire, 100 m × 0.12 W/m = 12 W equals the additional loss to be taken into account. UM-5055, Rev. 1.0.9, 2022/04/29 Copyright ADB Safegate, All Rights Reserved ©...
  • Page 84 AXON Runway Inset Lights CABLE LOSS Copyright ADB Safegate, All Rights Reserved ©...

  • Page 85: Support

    10.2.1 Local Authority Recycling The disposal of ADB SAFEGATE products is to be made at an applicable collection point for the recycling of electrical and electronic equipment. The correct disposal of equipment prevents any potential negative consequences for the environment and human health, which could otherwise be caused by inappropriate waste handling.

  • Page 86: Adb Safegate Recycling

    Main Unit Serial Number. ADB SAFEGATE will continue to monitor and update according for any future requirements for EU directives as and when EU member states implement new regulations and or amendments. It is our aim to maintain our compliance plan and assist our customers.
  • Page 87 Tel.: +46 (0)40 699 17 00, Internet: www.adbsafegate.com Fax: +46 (0)40 699 17 30 ADB SAFEGATE Airfield Technologies Ltd. China ADB SAFEGATE, China: Unit 603, D Block, CAMIC International Convention Center, No 3, Hua Jia Di East road, ChaoYang district, Beijing 100102 P.R.

This manual is also suitable for:

Axon ta 5052Axon tb 5052Axon tc 5052Axon td 5052Axon tj 5052Axon tk 5052 ... Show all

Table of Contents