Preparation For Work; Using The Tool - BorMann PRO BMF5000 Manual

EN
Use and care of the power tool
Do not overload the power tool. Use the power tool appropriate for the selected application. The right power tool will provide a better and safer job if used
according to the designed load. Do not use the power tool, if the electric switch does not allow switching on and off. Power tool, which cannot be controlled
by means of a power switch is dangerous and must be returned for repair. Disconnect the plug from the power socket and / or remove the battery if it is de-
tachable from the power tool before adjusting, changing accessories or storing the tool. Such preventive measures will allow you to avoid accidentally turning
on the power tool. Keep the tool out of the reach of children, do not let people who do not know how to operate the power tool or these instructions use a
power tool. Power tools are dangerous in the hands of untrained users. Maintain power tools and accessories. Check the tool for mismatches or jams of moving
parts, damage to parts and any other conditions that may affect the operation of the power tool. Damage must be repaired before using the power tool. Many
accidents are caused by incorrectly maintained tools. Keep cutting tools sharp and clean. Properly maintained cutting tools with sharp edges are less prone to
jamming and are easier to control when working. Use power tools, accessories and inserted tools etc. in accordance with these instructions, taking into account
the type and conditions of work. The use of tools for work other than designed is likely to result in a dangerous situation. Handles and gripping surfaces must be
dry, clean and free from oil and grease. Slippery handles and gripping surfaces do not allow for safe operation and control of the tool in dangerous situations.
Repairs
Repair the power tool only in authorized facilities using only original spare parts. This ensures proper operation safety of the power tool.
Operation of the tool
Mounting the inserted tool
Attention! The steps described in this chapter should be carried out only when the power supply is a disconnected. Pull the plug of tool out from the socket!
During installation of the inserted tool equipped with sharp edges, be careful and use personal protective equipment, in particular protective gloves. Lift, and
then turn for 180 degrees the lever of the quick installation mechanism (Il). Install the inserted tool which is designed for the selected type of work. Mount
the inserted tool holder on the spindle handle so that the work was as easy as possible, yet safe. Attention! It is prohibited to assembly at the place, where the
working part of the inserted tool (blade) would be directed towards the tool operator. Make sure, that the holes of the tool are inserted in line with the pins of
the handle spindle (III). Attention! It is prohibited to mount the tool of the place where the inserted tool will be mounted with less than two pins. Attention! It
is possible to install the inserted tools with open or closed mount. The lever of mechanism for rapid installation is equipped with protection, which protects the
operator's fingers against being trapped by the descending lever. Before you completely lower the lever you should move the protection to the position which is
enabling to close the lever (IV). Turn the lever of the quick installation mechanisms for 180 degrees, allowing the inserted tool to be mounted int spindle handle.
Push the lever of the quick installation, so as to protect it from accidental opening during its operation (IV).
Attention! Adapter for grinding may be provided with a pad located in the mounting hole, before mounting adapter for grinding, the pad should be removed
from the opening, for example by a small screwdriver.
Mounting the abrasive sheet (V)
When you select as an inserted tool the adapter for grinding, before starting the work you need to install on it sanding sheet. The is equipped with a velcro
pad, to which the sanding sheet should be attached in such a way so the edges of the sheet would covered with the adapter edges. For adapters which are
equipped with holes for dust extraction, you should apply sanding sheets with holes. While attaching the sheet to adapter, you should ensure that the holes in
sheet would cover the holes in adapter.
Dust extraction (VII)
The tool is equipped with the attached dust extraction system. Dust extraction fulfills its role only in the case of work performed with the grinding adapter. The
dust extraction should be installed before installing the grinding adapter. The front part of the exhaust should be translated through the spindle so, the catches
would be blocked on the protrusions of tool housing. The rear part of the dust extraction should be secured with clamp engaging at the bottom row of the rear
air vents. Dust extraction outlet should be connected to an external dust extraction system. In the case of using an external installation of dust extraction you
should follow the instructions supplied with these installations.
Installation of the auxiliary handle (VIII)
The tool enables for a two-handed grip, even without mounted auxiliary handle, but where the handle will not interfere with the work, e.g. due to lack of space,
it should be installed by firm screwing to the hole in the housing on the left or right side.

Preparation for work

Remove the plug of the power supply cable from the socket. Before any work with the tool, it is required to make sure the housing and the connection cord with
plug are not damaged. In case any damage is detected, it is prohibited to connect the tool to the mains! Insert the insertion tool designed for the given kind
of work. Wear eye and hearing protectors and working gloves. Make sure the switch is ,OFF", and then insert the plug of the power supply cable to the mains
socket. Adopt an adequate position, which guarantees stability during work and turn the tool on using the switch.

Using the tool

Commence work applying the insertion tool to the material to be processed. During work do not exert excessive pressure against the material being processed
and do not make sudden movements, so as to avoid any damage to the insertion tool or the abrasive sheet.Due to the level of vibration noise and dust generat-
ed by the tool, it is necessary to make regular breaks during work. Avoid overloading the tool, the temperature of the external surfaces at any time must not ex-
ceed 60°C. Always use individual protection means: working gloves, safety goggles and hearing protection. Remove accumulated dust from the abrasive sheet
from time to time. In order to do so turn the tool off and slightly tap the foot of the grinder. Do not process different materials using the same abrasive sheet!
Once the work has concluded turn the tool off, remove the plug of the power supply cable from the mains socket and realise maintenance and inspection of
the tool.
4
WWW.BORMANNTOOLS.COM