Trane S9V2B040U3PSBB Installer's Manual page 47

Furnace in Horizontal Right with "A" Coil
C C A A U U T T I I O O N N
C C O O I I L L R R E E Q Q U U I I R R E E M M E E N N T T ! ! ! !
F F a a i i l l u u r r e e t t o o f f o o l l l l o o w w t t h h i i s s C C a a u u t t i i o o n n c c o o u u l l d d r r e e s s u u l l t t i i n n
p p r r o o p p e e r r t t y y d d a a m m a a g g e e o o r r p p e e r r s s o o n n a a l l i i n n j j u u r r y y . .
4 4 G G X X C C * * a a n n d d 4 4 M M X X C C * * c c o o i i l l s s i i n n s s t t a a l l l l e e d d o o n n u u p p f f l l o o w w
f f u u r r n n a a c c e e s s i i n n v v e e r r t t i i c c a a l l , , h h o o r r i i z z o o n n t t a a l l l l e e f f t t , , o o r r h h o o r r i i z z o o n n t t a a l l
r r i i g g h h t t o o r r i i e e n n t t a a t t i i o o n n s s w w i i t t h h o o u u t t a a f f a a c c t t o o r r y y i i n n s s t t a a l l l l e e d d m m e e t t a a l l
d d r r a a i i n n p p a a n n s s h h i i e e l l d d m m u u s s t t u u s s e e a a M M A A Y Y * * F F E E R R C C O O L L K K I I T T A A A A k k i i t t . .
C C o o i i l l s s i i n n s s t t a a l l l l e e d d o o n n u u p p f f l l o o w w f f u u r r n n a a c c e e s s m m u u s s t t h h a a v v e e d d r r a a i i n n
p p a a n n s s t t h h a a t t a a r r e e s s u u i i t t a a b b l l e e f f o o r r 4 4 0 0 0 0 ° ° F F ( ( 2 2 0 0 5 5 ° ° C C ) ) o o r r h h a a v v e e a a
m m e e t t a a l l d d r r a a i i n n p p a a n n s s h h i i e e l l d d . . D D o o w w n n f f l l o o w w f f u u r r n n a a c c e e s s d d o o n n o o t t
r r e e q q u u i i r r e e a a m m e e t t a a l l d d r r a a i i n n p p a a n n s s h h i i e e l l d d o o r r t t h h e e u u s s e e o o f f t t h h e e
M M A A Y Y * * F F E E R R C C O O L L K K I I T T A A A A k k i i t t . . S S e e e e I I n n s s t t a a l l l l e e r r ' ' s s G G u u i i d d e e f f o o r r
m m o o r r e e i i n n f f o o r r m m a a t t i i o o n n . .
1. Cut the back flange along perforation.
2. Starting at the back of the furnace, cut the side flanges along
perforations until past the end of the heat shield to avoid
interference when bending.
3. Bend furnace side flanges down.
4. Support the furnace and coil independently.
Note: Flat or dedicated horizontal coils may require flanges to be bent
upward.
1. Match the coil up flush to the back of the furnace.
2. Seal per local codes and requirements.
18-CE01D1-1M-EN
F F u u r r n n a a c c e e G G e e n n e e r r a a l l I I n n s s t t a a l l l l a a t t i i o o n n
47