Table of Contents
Advertisement
Installation Checklist
1. Locate appliance
a) Room location (Refer to "Locating Your
Gas fireplace" section)
b) Clearances to Combustibles (Refer to
"Clearances" section)
c) Mantle Clearances (Refer to "Combustible
Mantel Clearances" section)
d) Framing & Finishing Requirements (Refer
to "Framing & Finishing" section)
e) Venting Requirements (Refer to "Venting"
section)
2. Assemble Top Standoffs and Top Facing Sup-
port and Side Nailing Strips (Refer to "Unit
Assembly Prior to Installation" Section).
NOTE: Must be done before installing unit
into place.
IMPORTANT: If installing the fan kit or
changing this from rear vent to top
vent, this must be completed prior to
installing the appliance into the framed
opening.
3. Install vent (Refer to "Venting" sections).
4. Make gas connections. Test the pilot. Must be
as per Diagram (Refer to "Pilot Adjustment
" section).
Convert to propane if desired (Refer to "Gas
Line Installation" and "Conversion Kit from
NG to LPG" sections).
5. Make electrical connections to receptacle
supplied with unit (recommended).
6. Install standard and optional features. Refer
to the following sections:
a. Standard Glass Door
b. Rear to top vent conversion
c. Coolwall conversion
d. Fan Installation (Optional)
e. Nailing flange installation
f. Electrical access/120 volt power installation
by others
g. Wall Mount ON/OFF Switch + Battery
Holder Installation
h. Coolwall Clearances/Framing/Finishing
i. Clean Front Clearance/ Framing/Finishing
j. Outside Finish Clearance/ Framing/
Finishing
k. LP Conversion (optional)
l. Inner Panels or Brick Panels (Must install
one of the options)
m. Media (Glass crystals)
n. Log Set Installation
o. Install 4AA batteries into battery pack
p. HeatWave Kit
7. Final check.
This includes:
1. Clocking the appliance to ensure the correct
firing rate (rate noted on label 27,000 Btu/h
for natural gas and propane), after burning
appliance for 15 minutes.
2. If required, adjusting the primary air to ensure
that the flame does not carbon. First allow
the unit to burn for 15-20 min. to stabilize.
CAUTION: Any alteration to the product that
causes sooting or carboning that results
in damage is not the responsibility of the
manufacturer.
Locating Your Gas Fireplace
1. When selecting a location for your fireplace,
ensure that the clearances are met.
2. The appliance must be installed on a flat,
solid, continuous surface For example a
wood, metal or concrete floor or in a raised
(on the wall) application. The appliance
must be installed on a metal or wood panel
extending the full width and depth of the
appliance.
3. The G800EC Gas Fireplace can be installed
in a recessed position or framed out into the
room as in A, B, C and D. See Diagram 1.
Diagram 1
A)
Flat on Wall
B)
Flat on Wall Corner
C)
Recessed into Wall/Alcove
D) Corner
installer's information
4. This appliance is Listed for bedroom installations
using the standard Remote (millivolt thermostat
system). Some areas may have further require-
ments, check local codes before installation.
5. The G800EC Gas Fireplace are approved for alcove
installations, see "Clearances" section for details.
6. We recommend that you plan your installa-
tion on paper using exact measurements for
clearances and floor protection before actually
installing this appliance. Have an authorized
inspector, dealer, or installer review your plans
before installation.
HeatWave Duct System
Optional Kit (Part #946-556)
The HeatWave Air Duct Kit increases the
effectiveness of your fireplace by dispersing warm
air from the fireplace to remote locations in the
same room or other rooms in your home.
Up to two kits may be installed on the fireplace.
Please Note: Only 1 HeatWave kit may be oper-
ated at one time. This includes the internal blower
option as well.
The HeatWave Duct Kit has different
clearance and framing requirements, check
the HeatWave manual for details.
Grandview
G800EC Gas Fireplace |
®
21
Advertisement
Table of Contents
