5. Installation
The installer shall identify a suitable location for the Energizer Homepower HP-6 Series system, maintain
recommended clearances, install the wall-mount bracket(s), carry out the electrical wiring, energize the system and
commission it using the Energizer Homepower Installer App. The installation procedure is best described as per
the flowchart below:
Identify
suitable
START
location for
installation
Install
CT
clamps
Fig. 4. Installation Flowchart
Step 1 – Planning the Installation
Always refer to local electrical standards while planning the Energizer Homepower HP-6 Series system
installation. Select a suitable wall that is accessible, ventilated, not facing direct sunlight and within close
proximity to the Main Switchboard (MSB), and ensure the area is isolated from hazards that may damage the
unit(s) or may be prone to flooding.
Removing the Units from the Package
With a minimum of 1 person either side of the box, reach down the sides of the unit to locate the cut outs in the
unit carrier device. Using the carrier device lift the unit from the box and place flat on the ground. The HP-6S
follows the same packaging design and can be unpacked similarly to the HP-6M unit.
6
1
7
2
3
1. Box Lid
2. Parts Holder
3. Padding
4
4. Lifting Device
5. Box Bottom
6. Accessories Box
7. Mounting Bracket
5
8. HP-6M (Main Unit)
Fig. 5. Unpacking the HP-6M Unit
V23-00220
6
Energizer Homepower HP-
Series - Installation Manual
Install
Install the
Install the
AC cabling
Energizer
wall-mount
& electrical
Homepower
bracket
protection
system
devices
Commission
the Energizer
Power-Up
END
Homepower
System
system using
the Installer App
1
8
7
2
3
4
1. Box Lid
2. Accessories Box
3. Parts Holder
5
4. Padding
5. Lifting Device
6. Box Bottom
7. HP-6S (Sub Unit)
6
Fig. 6. Unpacking the HP-6S Unit
16
© Energizer 2022
6
Energizer Homepower HP-
Series - Installation Manual
Step 2 – Transporting & Unpacking Energizer Homepower HP-6 Series Unit(s)
Keep the Energizer HP-6M unit(s) in their original package(s) until they are ready to be installed. Ensure that the
box is stored flat on its back during transport.
Open the box by removing the packing straps that hold the package together. Following this, open the lid, remove
the wall mounting bracket and the accessories box. Ensure that you have the items listed within Table 3. and check
for any damages that may have occurred during transit.
No.
Main Unit)
HP-6M (
Item
1
HP-6M (Main Unit)
2
Owner's Manual
3
Wall-Mount Bracket (Main Unit)
Accessories Box
•
Pre-terminated CT Sensors
•
M25 Conduit Connector
•
Antenna Module
•
SMA Extension Cable
4
•
Side Cover
•
M25 Al Hole Blockers
•
M5 Earthing Lugs
•
M8 Locking Bolt – 30 mm
Table 3. Package Contents
Step 3 – Installing the Units
Ensure the mounting location can accommodate the entire system including the clearances required and allows
access for electrical cabling through identified ports and provides a flat surface for the Energizer Homepower
HP-6 Series system to be mounted on. The Energizer Homepower HP-6 Series system can support one HP-6M
plus up to a maximum of three HP-6S units. Depending on the size of the system you plan to install, refer to the
dimensions below to plan the location of the units.
Fig. 7. System Dimensions & Minimum Clearance
V23-00220
Sub Unit)
HP-6S (
Qty
Item
1 pc
HP-6S (Sub Unit)
1 pc
Owner's Manual
1 pc
Wall-Mount Bracket (Sub Unit)
Accessories Box
2 pcs
•
DC Cables – 225 mm
3 pcs
•
DC Cables – 435 mm
•
CAT 5E Cable – 300mm
1 pc
1 pc
•
RJ 45 Connectors
1 pc
•
Earthing Cable 6mm2 – 500mm
4 pcs
•
M25 Glands
2 pcs
•
M20 Slotted 2-Hole Gland
1 pc
•
M6 Spring & Washer Set
•
M5 Earthing Lugs
17
© Energizer 2022
Qty
1 pc
1 pc
1 pc
2 pcs
2 pcs
1 pc
2 pcs
1 pc
4 pcs
2 pcs
4 pcs
2 pcs