Subscribe to Our Youtube Channel
Related Manuals for GABOR MD-ASL15W
Summary of Contents for GABOR MD-ASL15W
- Page 1 MD-ASL15W / SPRING LOADED MONITOR MOuNT For 15″ - 27″ (38.1-68.6 cm) LCD desktop computer monitors User Manual...
- Page 2 Thank you for choosing Gabor. The Gabor MD-ASL15W mounts your 15″–27″ (38.1–68.6 cm) LCD computer monitor. It attaches to your desk via a built-in clamp, freeing up valuable desk space and enabling personalized monitor placement for improved safety and comfort over conventional monitor stands.
- Page 3 Welcome...
-
Page 4: Installation
Overview Mounting Arm (x1) VESA Mount Locking Shaft collar Mounting socket Set screw Cable guides Clamp screws Clamp Tools Required For Installation Clamp locking knob • Phillips Screwdriver Overview... - Page 5 Also Included Supplied Parts & Hardware A (4) M4 × 12 screw D 5 mm hex key G (1) Shaft Cap M4x12 (x8) M4x30 (x8) B (4) M4 × 30 screw E (4) Spacer H User Manual C 3 mm hex key F Cable clip M4x12 (x8) M5x12 (x8)
- Page 6 90° Product Specifications 360° 360° Monitor display size: 15″–27″ (38.1–68.6 cm) Maximum load capacity (per arm): 17 lb. (7.8 kg) 85° VESA standard: 75 × 75, 100 × 100 Tilt: -90°/+85° +/-45° 180° Swivel: 180° Roll: 360° • Installation: Clamp fits desk edges up to 2.6″...
-
Page 7: Safety Warnings
Safety Warnings Please read and follow the instructions and Do not exceed the maximum load capacity. keep this manual in a safe place. Do not install this product on an unsteady Clean this product with only a soft, dry cloth. structure or one that is prone to vibration, has a chance of being impacted, or is susceptible to other movements. -
Page 8: Getting Started
GETTING STARTED: Decide where you want to place your monitor. You'll be positioning your monitor directly in front of you, at eye level, and approximately at an arm’s length away. You shouldn’t need to turn your head to look at your monitor. If you have to strain to look at it, you should readjust its position. - Page 9 If your desk is close to 2. Fit the clamp over the a wall or you don’t have edge of your desk, and • The MD-ASL15W easily enough clearance to fit tighten the clamp locking attaches to most desk the entire clamp behind knob until the shaft is edges up to 2.6″...
- Page 10 Limited Clearance 4. Reinsert the clamp screws and use the 1. Use the included 5 mm included 5 mm hex key hex key to remove the to fasten them until fully clamp screws. tightened. 2. Fit the top part of the 5.
- Page 11 ATTACHING YOUR MONITOR TO THE VESA MOUNTS: Before attaching your monitor to the VESA mount, you may need to detach your monitor’s built-in stand. For information on how to do this, consult your monitor’s user manual. Depending on how the back of your monitor is configured, you can use one of two methods to install the VESA mount onto your monitor: flush or recessed.
-
Page 12: Flush Installation
Flush Installation Note: Before starting, make 2. Align the mounting sure the VESA mount, holes in the VESA mount mounting arm, and with the corresponding monitor are facing the mounting holes in your monitor. proper direction. 3. Insert four of the included 1. -
Page 13: Recessed Installation
Recessed Installation Note: Before starting, make 2. Place four of the included Tip: Thread each of the sure the VESA mount, spacers on each of your screws by hand before mounting arm, and monitor’s four VESA fastening them with the monitor are facing the mounting holes. - Page 14 Attaching the Mounting Arm Assembly 1. You can remove the shaft by rotating it until fully 5. Insert your monitor cable cap from the shaft if you want. tightened. into the cable guides on the underside of the mounting 2. Rotate the locking collar 4.
- Page 15 Adjusting Tension and Articulation Note: Arm Tension To prevent your monitors To avoid damage, make from drooping, you can adjust Important! The arm tension sure to hold your monitor the tension of the mechanical is preset for lighter monitors. steady when making any spring in the mounting arms.
- Page 16 Arm Swivel Monitor Tilt and Swivel You can adjust the arms’ (horizontal) swivel You can adjust the (vertical) tilt and S=3mm action via the set screws on the rear of the (horizontal) swivel action of your monitor mounting socket. Position the arm as desired for optimal viewing comfort.
-
Page 17: Dedicated Accessories
The MWD-E8W extension arm adds 10″ (25.4 cm) of length and an additional point of articulation to provide greater freedom for positioning your monitor. The MW-C wall mount offers MWD-E8W an alternative mounting option for your MD-ASL15W monitor setup. Installation Instructions... -
Page 18: Customer Support
Customer ONE YEAR LIMITED WARRANTY: Support This GABOR product is warranted to the original purchaser to be free from defects in materials and workmanship under normal consumer use for a period of one (1) year For more information or from the original purchase date or thirty (30) days after replacement, whichever occurs later. - Page 19 Customer Support / Warranty...
- Page 20 MADEBYGABOR WWW. .COM...
Need help?
Do you have a question about the MD-ASL15W and is the answer not in the manual?
Questions and answers