Page 1 Frontload Washer Refer to Page 12 for Model Identification Wash REGULAR DELUXE ULTRA Cycle NORMAL SYNTHETIC DELICATE START Temp COLD WARM FLW1556C_SVG Original Instructions Keep These Instructions for Future Reference. CAUTION: Read the instructions before using the machine. (If this machine changes ownership, this manual must accompany machine.) Part No.
Page 3 Read all instructions before using unit. Hazardous voltage inside. Disconnect power before serv- icing. This product uses FreeRTOS V7.2.0 (www.freertos.org). © Copyright, Alliance Laundry Systems LLC - Part No. 807870ENR3 DO NOT COPY or TRANSMIT...
Page 4: Regulatory Statements
Users of this product are cautioned not to make modifications or firmware-limited to Channel 1 through 11. changes that are not approved by Alliance Laundry Systems, LLC. Doing so may void the compliance of this product with ap- CANADA - CAN ICES-3(B)/NMB-3(B) plicable laws and regulatory requirements and may result in the loss of the user’s authority to operate the equipment.
Page 5 The user must stop operating the device immediately should harmful interference is caused and shall not resume until © Copyright, Alliance Laundry Systems LLC - Part No. 807870ENR3 DO NOT COPY or TRANSMIT...
Page 6: Table Of Contents
Cycle Sequence.................... 16 © Copyright 2021, Alliance Laundry Systems LLC All rights reserved. No part of the contents of this book may be reproduced or transmitted in any form or by any means without the expressed written consent of the publisher.
Page 7 Vend Price 1 AtS 1..................44 Vend Price 2 AtS 2..................45 Vend Price 3 AtS 3..................46 Vend Price 4 AtS 4..................46 Vend Price 5 AtS 5..................46 © Copyright, Alliance Laundry Systems LLC - Part No. 807870ENR3 DO NOT COPY or TRANSMIT...
Page 8 How to Program Special Vend 1 Vend Price 9 SP1 19........68 How to Program Special Vend 1 Wash Status Agitate Steps Added Minutes SP1 20......................68 © Copyright, Alliance Laundry Systems LLC - Part No. 807870ENR3 DO NOT COPY or TRANSMIT...
Page 9 Manual Diagnostics diAgEn................89 Factory Test Ft En..................89 Lucky Cycle LUC-..................90 Speed Units SUnitS..................90 Programmable Close Door Display PCdL d.............90 Programmable Push Start Display PPSt_d............91 © Copyright, Alliance Laundry Systems LLC - Part No. 807870ENR3 DO NOT COPY or TRANSMIT...
Page 10 Configuration 1 Display Test d 29............. 101 Configuration 2 Display Test d 30............. 104 Configuration 3 Display Test d 31............. 104 Configuration 4 Display Test d 32............. 104 © Copyright, Alliance Laundry Systems LLC - Part No. 807870ENR3 DO NOT COPY or TRANSMIT...
Page 11 How to Clear Vend..................115 Power Fail Recovery................116 Communications Mode................117 Near Field Communications................. 117 Card Reader Communications - Card Models Only........117 Network Communications................117 Default Cycle Time................118 © Copyright, Alliance Laundry Systems LLC - Part No. 807870ENR3 DO NOT COPY or TRANSMIT...
Page 12: Model Identification
SFNNYASP116TW01 HFNNXASP116CW01 SFNNYRSP116TW01 HTENXASP286CW01 STENCASP176TW01 HTENYASP286CW01 STENCFSP176TW01 HTGNXASP096CW01 STENXASP176TW01 SFNNCASG116TN01 STENYASP176TW01 SFNNCASG116TW01 STENYFSP176TW01 SFNNCASP116TN01 STGNCASP116TW01 SFNNCASP116TW01 STGNCFSP116TW01 SFNNCRSP116TW01 STGNXASP116TW01 SFNNXASP116TW01 STGNXFSP116TW01 SFNNXRSP116TW01 STGNYASP116TW01 SFNNYASG116TW01 STGNYFSP116TW01 © Copyright, Alliance Laundry Systems LLC - Part No. 807870ENR3 DO NOT COPY or TRANSMIT...
Page 13: Preliminary Information
On drain pump models, if the wash basket is full of water, the control will lock the door and pump out the water. © Copyright, Alliance Laundry Systems LLC - Part No. 807870ENR3 DO NOT COPY or TRANSMIT...
Page 14: Control Identification
3. Six 7-Segment Digits 4. Display 5. LED Status Lights 6. SELECT Cycle Modifier pads 7. START pad 8. SELECT WASH TEMP pads Figure 1 © Copyright, Alliance Laundry Systems LLC - Part No. 807870ENR3 DO NOT COPY or TRANSMIT...
Page 15: Display Identification
DELUXE LED is lit when the Option DELUXE modifier is se- lected. ULTRA LED ULTRA LED is lit when the Option ULTRA modifier is selected. © Copyright, Alliance Laundry Systems LLC - Part No. 807870ENR3 DO NOT COPY or TRANSMIT...
Page 16: Washer Operation
After pressing the START keypad, the door will lock and the cy- completes will be added to the total coin counter, but the user will cle will begin. not be able to change cycles. © Copyright, Alliance Laundry Systems LLC - Part No. 807870ENR3 DO NOT COPY or TRANSMIT...
Page 17: Closing Washer Door
Start Mode will be exited and the control will enter Start Mode. Pause/Resume Mode (Enable/Disable) parameter is programmed to Enabled and if the control is in Run Mode or Door Locking Mode. © Copyright, Alliance Laundry Systems LLC - Part No. 807870ENR3 DO NOT COPY or TRANSMIT...
Page 18: Auto Flush Mode
Lockout Mode is exited. The control will be able to communicate with the Network, NFC, or the Serial Pay- ment System. © Copyright, Alliance Laundry Systems LLC - Part No. 807870ENR3 DO NOT COPY or TRANSMIT...
Page 19: Special Features
These modes include Manual Programming, Audit Collection, * Tests can only be entered when in Start or Ready Mode. Diagnostics, Rapid Advance, and Reset to Factory Defaults. © Copyright, Alliance Laundry Systems LLC - Part No. 807870ENR3 DO NOT COPY or TRANSMIT...
Page 20: Break-In Alarm
Out of Order Mode is active. © Copyright, Alliance Laundry Systems LLC - Part No. 807870ENR3 DO NOT COPY or TRANSMIT...
Page 21: Opening The Service Door
“white/black” and “red/blue” wires. This will allow the user to access various programming options, diagnostics, and audit capa- bilities. Refer to Figure 3 . © Copyright, Alliance Laundry Systems LLC - Part No. 807870ENR3 DO NOT COPY or TRANSMIT...
Page 22: 45 Degree Front Control Models
4. Remove the screws from the bottom of the control panel that attach the control panel to the machine. FLW2384N_SVG FLW32R_SVG Figure 4 W521I_SVG FLW6R_SVG1 1. Service Door 2. Control Panel Figure 3 © Copyright, Alliance Laundry Systems LLC - Part No. 807870ENR3 DO NOT COPY or TRANSMIT...
Page 23: Entering The Manual Mode
8. To exit, press the WARM ( < ) keypad. The control will revert back to Ready Mode. © Copyright, Alliance Laundry Systems LLC - Part No. 807870ENR3 DO NOT COPY or TRANSMIT...
Page 24 Diagnostic Tests. Refer to Tests Diagnostic Tests flowchart. "WiFi" Press the START keypad to WiFi enter WiFi Menu. Refer to WiFi flowchart. FLW212R_SVG Figure 5 © Copyright, Alliance Laundry Systems LLC - Part No. 807870ENR3 DO NOT COPY or TRANSMIT...
Page 25 "MAC" Press the START (enter) MAC Address keypad to read MAC. Press the START (enter) "DiSCon" keypad to disconnect from SSID. Disconnect State TLW58R-b_SVG © Copyright, Alliance Laundry Systems LLC - Part No. 807870ENR3 DO NOT COPY or TRANSMIT...
Page 26: Programming Control
1 - 65,535 dEn 1 Coin #2 Value 1 - 65,535 dEn 2 Serial Payment Config- CArd oFF, SEriAL, CArd, S SErPAy uration PLSE Table continues... © Copyright, Alliance Laundry Systems LLC - Part No. 807870ENR3 DO NOT COPY or TRANSMIT...
Page 27 E dr 1 Drain Error Time 15 = Through Serial 1 - 59 E dr 2 No. 1507032556 5 = Starting Serial No. 1507032557 Table continues... © Copyright, Alliance Laundry Systems LLC - Part No. 807870ENR3 DO NOT COPY or TRANSMIT...
Page 28 Low Water Level 1 - 30 FL Lo Medium Water Level 1 - 30 FL NEd High Water Level 1 - 30 FL Hi Table continues... © Copyright, Alliance Laundry Systems LLC - Part No. 807870ENR3 DO NOT COPY or TRANSMIT...
Page 29 9 Special Vend 1 Param- — — SP1- eters Menu Special Vend 1 Days of Refer to Table 9 SP1 1 Week Enable Table continues... © Copyright, Alliance Laundry Systems LLC - Part No. 807870ENR3 DO NOT COPY or TRANSMIT...
Page 30 0 - 65,535 SP1 17 Special Vend 1 Price 0 - 65,535 SP1 18 Special Vend 1 Price 0 - 65,535 SP1 19 Table continues... © Copyright, Alliance Laundry Systems LLC - Part No. 807870ENR3 DO NOT COPY or TRANSMIT...
Page 31 Cycle Modifier Key # 0 - 31 CNP 3 2 Heavy Options Cycle Modifier Medi- 0 - 15 CNP 4 um Additional Wash Time Table continues... © Copyright, Alliance Laundry Systems LLC - Part No. 807870ENR3 DO NOT COPY or TRANSMIT...
Page 32 1506011826 = 4 Time Starting Serial No. 1506011827 = 7 Cycle Pause Resume on/oFF CyCPAU Low Power/Auto Shut- on/oFF LPAS 1 down 1 Days Enable Table continues... © Copyright, Alliance Laundry Systems LLC - Part No. 807870ENR3 DO NOT COPY or TRANSMIT...
Page 33 PPSt d Start Display Programmable Open on/oFF PodL d Door Display Vend Price Display on/oFF AtS do Override OPL Parameters — — oPL- Table continues... © Copyright, Alliance Laundry Systems LLC - Part No. 807870ENR3 DO NOT COPY or TRANSMIT...
Page 34 1 OPL Delayed Start on/oFF oPL 2 OPL Display Power on/oFF oPL 3 Save Drop Off Mode on/oFF droP Out of Order on/oFF © Copyright, Alliance Laundry Systems LLC - Part No. 807870ENR3 DO NOT COPY or TRANSMIT...
Page 35 Vend Price Decimal Point "dEn 1" Coin #1 Value "dEn 2" Coin #2 Value "SErPAy” Serial Payment Configuration "CardEn" Card Enable continued FLW210R_SVG Figure 6 © Copyright, Alliance Laundry Systems LLC - Part No. 807870ENR3 DO NOT COPY or TRANSMIT...
Page 36 "E nF-" "E nF 1" No Water Flow Error No Water Flow Error "E nF 2" No Water Flow Error Time continued FLW214R_SVG Figure 7 © Copyright, Alliance Laundry Systems LLC - Part No. 807870ENR3 DO NOT COPY or TRANSMIT...
Page 37 Display Sequence "E Sd- " "E Sd 1" Slow Drain Slow Drain Detection Detection Error "E Sd 2" Slow Drain Detection Adjust continued FLW215R_SVG Figure 8 © Copyright, Alliance Laundry Systems LLC - Part No. 807870ENR3 DO NOT COPY or TRANSMIT...
Page 38 "FL Hi" High Water Level "FLSH t" Flush Out Time for Fill Steps "norF t" No Refill After Time for Agitate Step continued FLW104R_SVG Figure 9 © Copyright, Alliance Laundry Systems LLC - Part No. 807870ENR3 DO NOT COPY or TRANSMIT...
Page 39 Start Hour "dLS 6" End Month "dLS 7" End Day of Week "dLS 8" End Week of Month "dLS 9" End Hour continued FLW90R-e_SVG Figure 10 © Copyright, Alliance Laundry Systems LLC - Part No. 807870ENR3 DO NOT COPY or TRANSMIT...
Page 40 Special Vend 1 Price #4 Extract Speed Limit "SP1 15" Special Vend 1 Price #5 "SP1 16" Special Vend 1 Price #6 continued FLW108R_SVG Figure 11 © Copyright, Alliance Laundry Systems LLC - Part No. 807870ENR3 DO NOT COPY or TRANSMIT...
Page 41 Added Agitate Time to Wash Status Agitate Steps "CMP 7" Cycle Modifier Key #2 Added Agitate Time to Rinse 1 Status Agitate Steps continued FLW109R_SVG Figure 12 © Copyright, Alliance Laundry Systems LLC - Part No. 807870ENR3 DO NOT COPY or TRANSMIT...
Page 42 Hold Step Custom Message #1 Custom Messages "PCyCtd" “CMESS2” Cycle Time Custom Message #2 Display Enable "nCyCtd" No Cycle Time Display continued FLW90R-h_SVG Figure 13 © Copyright, Alliance Laundry Systems LLC - Part No. 807870ENR3 DO NOT COPY or TRANSMIT...
Page 43 Power Fail Reset "NFC En" NFC Access (On/Off) "rAPdEn" Manual Rapid Advance (On/Off) "diAgEn" Manual Diagnostics (On/Off) "Ft En" Factory Test Cycle (On/Off) continued FLW211R_SVG Figure 14 © Copyright, Alliance Laundry Systems LLC - Part No. 807870ENR3 DO NOT COPY or TRANSMIT...
Page 44: Vend Price 1 Ats 1
OPL Delayed Start (On/Off) Drop Off Mode "oPL 3" "oUt " OPL Display Power Save (On/Off) Out of Order FLW217R_SVG Figure 15 Vend Price 1 AtS 1 © Copyright, Alliance Laundry Systems LLC - Part No. 807870ENR3 DO NOT COPY or TRANSMIT...
Page 45: Vend Price 2 Ats 2
5. Press the START (enter) keypad when the correct value ap- pears in the display. The new value is saved and the next op- tion will appear in the display. © Copyright, Alliance Laundry Systems LLC - Part No. 807870ENR3 DO NOT COPY or TRANSMIT...
Page 46: Vend Price 3 Ats 3
Vend Price 4 AtS 4 © Copyright, Alliance Laundry Systems LLC - Part No. 807870ENR3 DO NOT COPY or TRANSMIT...
Page 47 NOTE: To go back to the current programmable op- 5. When AtS 9 appears in the display, press the START (enter) tion without changing the value, press the WARM (<) keypad. keypad. © Copyright, Alliance Laundry Systems LLC - Part No. 807870ENR3 DO NOT COPY or TRANSMIT...
Page 48 ACNP 2 appears in 1. Control must be in Manual Mode. Refer to How to Enter the the display. Manual Mode. © Copyright, Alliance Laundry Systems LLC - Part No. 807870ENR3 DO NOT COPY or TRANSMIT...
Page 49 The new value is saved and the next op- in the control. tion will appear in the display. Table 1 continues... © Copyright, Alliance Laundry Systems LLC - Part No. 807870ENR3 DO NOT COPY or TRANSMIT...
Page 50 Pulse Input of the control to start the cycle. If set for single pulse, Start Pulse Value PLSdEn one start pulse from the central system will start the cycle. If set © Copyright, Alliance Laundry Systems LLC - Part No. 807870ENR3 DO NOT COPY or TRANSMIT...
Page 51 Press the START (enter) keypad, and tered of Cycle Mode is entered AtS 1 will appear in the display. Table 3 continues... © Copyright, Alliance Laundry Systems LLC - Part No. 807870ENR3 DO NOT COPY or TRANSMIT...
Page 52 To determine the correct number required to program the Audio Signal, use the following chart. The Signal Value column con- © Copyright, Alliance Laundry Systems LLC - Part No. 807870ENR3 DO NOT COPY or TRANSMIT...
Page 53 The default value programmed at the factory is 29. Serial or Net- work Vending Command Coin/Card In- Signal Value Start Mode Signal End of Cycle Key Pressed Table 5 continues... © Copyright, Alliance Laundry Systems LLC - Part No. 807870ENR3 DO NOT COPY or TRANSMIT...
Page 54 This option allows the owner to turn on or turn off certain errors tion will appear in the display. in the control. 1. Control must be in Manual Mode. Refer to How to Enter the Manual Mode. © Copyright, Alliance Laundry Systems LLC - Part No. 807870ENR3 DO NOT COPY or TRANSMIT...
Page 55 Drain Error Time - Time allowed in mi- E dr 2 nutes to reach an empty water level be- fore setting the drain error. Table 6 continues... © Copyright, Alliance Laundry Systems LLC - Part No. 807870ENR3 DO NOT COPY or TRANSMIT...
Page 56 Suds Removal Routines allowed have been run in the cycle. Will be cleared after one minute or if a key is pressed. Table 6 continues... © Copyright, Alliance Laundry Systems LLC - Part No. 807870ENR3 DO NOT COPY or TRANSMIT...
Page 57 This option allows the owner to set the medium water level display. which can be used in fill steps to set water levels in cycle pro- gramming. © Copyright, Alliance Laundry Systems LLC - Part No. 807870ENR3 DO NOT COPY or TRANSMIT...
Page 58 This option allows the owner to set the controls internal clock to the correct time and date. 1. Control must be in Manual Mode. Refer to How to Enter the Manual Mode. © Copyright, Alliance Laundry Systems LLC - Part No. 807870ENR3 DO NOT COPY or TRANSMIT...
Page 59 Press the START (enter) keypad, and through the programmable options. Refer to Table 8 . AtS 1 will appear in the display. © Copyright, Alliance Laundry Systems LLC - Part No. 807870ENR3 DO NOT COPY or TRANSMIT...
Page 60 * The default value programmed at the factory is 0. tion will appear in the display. SP1 1, E Ld 1 and LUC 1 VALUE THUR ON/OFF Table 9 continues... © Copyright, Alliance Laundry Systems LLC - Part No. 807870ENR3 DO NOT COPY or TRANSMIT...
Page 61 Programming Control SP1 1, E Ld 1 and LUC 1 VALUE THUR ON/OFF Table 9 continues... © Copyright, Alliance Laundry Systems LLC - Part No. 807870ENR3 DO NOT COPY or TRANSMIT...
Page 62 Programming Control SP1 1, E Ld 1 and LUC 1 VALUE THUR ON/OFF Table 9 continues... © Copyright, Alliance Laundry Systems LLC - Part No. 807870ENR3 DO NOT COPY or TRANSMIT...
Page 63 Programming Control SP1 1, E Ld 1 and LUC 1 VALUE THUR ON/OFF Table 9 continues... © Copyright, Alliance Laundry Systems LLC - Part No. 807870ENR3 DO NOT COPY or TRANSMIT...
Page 64 Programming Control SP1 1, E Ld 1 and LUC 1 VALUE THUR ON/OFF Table 9 continues... © Copyright, Alliance Laundry Systems LLC - Part No. 807870ENR3 DO NOT COPY or TRANSMIT...
Page 65 3. Press the DELICATE (∧) or the HOT (∨) keypad to increase or decrease the start month to the desired month. © Copyright, Alliance Laundry Systems LLC - Part No. 807870ENR3 DO NOT COPY or TRANSMIT...
Page 66 3. Press the DELICATE (∧) or the HOT (∨) keypad to increase through the programmable Special Vend 1 options until SP1 or decrease the value to the desired date. 11 appears in the display. © Copyright, Alliance Laundry Systems LLC - Part No. 807870ENR3 DO NOT COPY or TRANSMIT...
Page 67 THETIC COLD wash in Special Vend 1. The corresponding pad to enter the value of the digit and advance to the next dig- LEDs will be lit while programming. © Copyright, Alliance Laundry Systems LLC - Part No. 807870ENR3 DO NOT COPY or TRANSMIT...
Page 68 Wash in Special Vend 1. 3. Press the DELICATE (∧) or the HOT (∨) keypad to increase or decrease the value of the active digit and the START key- © Copyright, Alliance Laundry Systems LLC - Part No. 807870ENR3 DO NOT COPY or TRANSMIT...
Page 69 ULTRA keypad is active. Refer to Table 1. © Copyright, Alliance Laundry Systems LLC - Part No. 807870ENR3 DO NOT COPY or TRANSMIT...
Page 70 6. Press the START (enter) keypad when the correct value ap- pears in the display. The new value is saved and the next op- tion will appear in the display. © Copyright, Alliance Laundry Systems LLC - Part No. 807870ENR3 DO NOT COPY or TRANSMIT...
Page 71 “OFF” that indicates if that column’s feature is turned on or off when the value is entered. Select the desired combination of fea- tures and enter the number found in the value column. © Copyright, Alliance Laundry Systems LLC - Part No. 807870ENR3 DO NOT COPY or TRANSMIT...
Page 72 State set to State set to Configuration cles set to Rinse 1 set to Wash Nod 2 Nod 1 Value 2 ** 3 *** Table 11 continues... © Copyright, Alliance Laundry Systems LLC - Part No. 807870ENR3 DO NOT COPY or TRANSMIT...
Page 73 CNP 3 appears in the time option needs to be turned on for the Cycle Modifier DE- display. LUXE Additional Wash Time to take effect. © Copyright, Alliance Laundry Systems LLC - Part No. 807870ENR3 DO NOT COPY or TRANSMIT...
Page 74 The new value is saved and the next op- keypad. A number will appear in the display corresponding to tion will appear in the display. © Copyright, Alliance Laundry Systems LLC - Part No. 807870ENR3 DO NOT COPY or TRANSMIT...
Page 75 Increases parameter val- rameter. cle Time Display Param- rameter. eter, key press increases parameter value, other- wise moves to next Step Type. Table 12 continues... © Copyright, Alliance Laundry Systems LLC - Part No. 807870ENR3 DO NOT COPY or TRANSMIT...
Page 76 Step 50 up a location. Step 50 is reset as an invalid step. Table 12 © Copyright, Alliance Laundry Systems LLC - Part No. 807870ENR3 DO NOT COPY or TRANSMIT...
Page 77 SPEEd XXFi11 no rot, LoW Ag, rEg 10 - 50 RPMs (0.03 - 0.77 G Force) Reversing rEvErS XXFi12 rEv on, no rEv Table 13 © Copyright, Alliance Laundry Systems LLC - Part No. 807870ENR3 DO NOT COPY or TRANSMIT...
Page 78 External Output #2 oUtP 2 XXSU20 oFF, on External Output #3 oUtP 3 XXSU21 oFF, on External Output #4 oUtP 4 XXSU22 oFF, on Table 14 © Copyright, Alliance Laundry Systems LLC - Part No. 807870ENR3 DO NOT COPY or TRANSMIT...
Page 79 Step 2 Agitate Step Step 3 Supply Step Acts as own step Step 4 Fill Step Step 5 Supply Step Active with Step 4 Table 16 © Copyright, Alliance Laundry Systems LLC - Part No. 807870ENR3 DO NOT COPY or TRANSMIT...
Page 80 External Output #2 oUtP 2 XXAg16 oFF, on External Output #3 oUtP 3 XXAg17 oFF, on External Output #4 oUtP 4 XXAg18 oFF, on Table 17 © Copyright, Alliance Laundry Systems LLC - Part No. 807870ENR3 DO NOT COPY or TRANSMIT...
Page 81 External Output #2 oUtP 2 XXSo16 oFF, on External Output #3 oUtP 3 XXSo17 oFF, on External Output #4 oUtP 4 XXSo18 oFF, on Table 18 © Copyright, Alliance Laundry Systems LLC - Part No. 807870ENR3 DO NOT COPY or TRANSMIT...
Page 82 External Output #2 oUtP 2 XXdr11 oFF, on External Output #3 oUtP 3 XXdr12 oFF, on External Output #4 oUtP 4 XXdr13 oFF, on Table 19 © Copyright, Alliance Laundry Systems LLC - Part No. 807870ENR3 DO NOT COPY or TRANSMIT...
Page 83 The programmed time will also include the ramp down time with an estimated ramp down rate of 24 RPMs/ second. For example, if spinning at a rate of 600 RPMs, the ma- © Copyright, Alliance Laundry Systems LLC - Part No. 807870ENR3 DO NOT COPY or TRANSMIT...
Page 84 External Output #2 oUtP 2 XXAU07 oFF, on External Output #3 oUtP 3 XXAU08 oFF, on External Output #4 oUtP 4 XXAU09 oFF, on Table 21 © Copyright, Alliance Laundry Systems LLC - Part No. 807870ENR3 DO NOT COPY or TRANSMIT...
Page 85 In both cases a Start key press will al- this functionality by setting the steps as Mod 1 or Mod 2. Refer to low the cycle to resume. Cycle Modifier Programming CNP-. © Copyright, Alliance Laundry Systems LLC - Part No. 807870ENR3 DO NOT COPY or TRANSMIT...
Page 86 1. Control must be in Manual Mode. Refer to How to Enter the for the normal allocated time. Further attempts beyond the pro- Manual Mode. © Copyright, Alliance Laundry Systems LLC - Part No. 807870ENR3 DO NOT COPY or TRANSMIT...
Page 87 6. Press the START (enter) keypad when the correct value ap- pears in the display. The new value is saved and the next op- tion will appear in the display. © Copyright, Alliance Laundry Systems LLC - Part No. 807870ENR3 DO NOT COPY or TRANSMIT...
Page 88 6. Press the START (enter) keypad when the correct value ap- pears in the display. The new value is saved and the next op- tion will appear in the display. © Copyright, Alliance Laundry Systems LLC - Part No. 807870ENR3 DO NOT COPY or TRANSMIT...
Page 89 3. Press the DELICATE (∧) or the HOT (∨) keypad to scroll through the programmable options until Ft En appears in the through the programmable options until rAPdEn appears in display. the display. © Copyright, Alliance Laundry Systems LLC - Part No. 807870ENR3 DO NOT COPY or TRANSMIT...
Page 90 1 value until vend is satis- keypad. The current status will appear in the display. fied. on = Option Enabled (factory default setting) Table 26 oFF = Option Disabled © Copyright, Alliance Laundry Systems LLC - Part No. 807870ENR3 DO NOT COPY or TRANSMIT...
Page 91 This option allows the owner to place the control in OPL Mode, the current status. in which no vend price needs to be satisfied in order to start the © Copyright, Alliance Laundry Systems LLC - Part No. 807870ENR3 DO NOT COPY or TRANSMIT...
Page 92 = Option Disabled (factory default setting) oFF = Option Disabled (factory default setting) 7. Press the DELICATE (∧) or the HOT (∨) keypad to change the current status. © Copyright, Alliance Laundry Systems LLC - Part No. 807870ENR3 DO NOT COPY or TRANSMIT...
Page 93 6. Press the START (enter) keypad when the correct value ap- pears in the display. The new value is saved and the next op- tion will appear in the display. © Copyright, Alliance Laundry Systems LLC - Part No. 807870ENR3 DO NOT COPY or TRANSMIT...
Page 94 Total Number of Start Pulses PULSE Total Number of Rapid Ad- rAPCyC vance Cycles Total Number of Run Hours rUnHrS Resettable Coin #1 Count rCoin1 Table 27 continues... © Copyright, Alliance Laundry Systems LLC - Part No. 807870ENR3 DO NOT COPY or TRANSMIT...
Page 95 6 Cycle 7 rCyC 7 Cycle 8 rCyC 8 Cycle 9 rCyC 9 All Cycles ALLCyC All Cycles and Global Pro- gramming Parameters Table 28 © Copyright, Alliance Laundry Systems LLC - Part No. 807870ENR3 DO NOT COPY or TRANSMIT...
Page 96 CL Coin Drop #1 Input Test d 10 C1 -- Coin Drop #2 Input Test d 11 C2 -- Table 29 continues... © Copyright, Alliance Laundry Systems LLC - Part No. 807870ENR3 DO NOT COPY or TRANSMIT...
Page 97 Machine Configuration #4 Display Test d 32 d --- Machine Configuration #5 Display Test d 33 E --- Card Reader Communication Test d 47 noCnFg or CoM--- Table 29 © Copyright, Alliance Laundry Systems LLC - Part No. 807870ENR3 DO NOT COPY or TRANSMIT...
Page 98 Display Test Input Test "d 33" Machine Configuration #5 "d 17" Show Fill Display Test Time Test "d 47" Card Reader Communication Test FLW213R_SVG Figure 16 © Copyright, Alliance Laundry Systems LLC - Part No. 807870ENR3 DO NOT COPY or TRANSMIT...
Page 99 CH oP when the wiring connection is open and CH CL when the connection is closed. To exit Vend Connection Header Present Test, press the WARM (<) keypad. The control will return to the Testing Mode. © Copyright, Alliance Laundry Systems LLC - Part No. 807870ENR3 DO NOT COPY or TRANSMIT...
Page 100 Show Drain Time Test d 18 This test will display the average drain time. This average will be calculated by taking the average of the last 10 drain times. © Copyright, Alliance Laundry Systems LLC - Part No. 807870ENR3 DO NOT COPY or TRANSMIT...
Page 101 This will display the DC Bus Voltage. To start test, control must be in the Testing Mode. Refer to How to Enter Testing Feature at the beginning of this section. © Copyright, Alliance Laundry Systems LLC - Part No. 807870ENR3 DO NOT COPY or TRANSMIT...
Page 102 Board "A" Vend Con- Configura- Jumper Header Header nection Coin Drop Coin Drop tion Value Present Present Present Present #2 Present #1 Present Table 30 continues... © Copyright, Alliance Laundry Systems LLC - Part No. 807870ENR3 DO NOT COPY or TRANSMIT...
Page 103 Board "A" Vend Con- Configura- Jumper Header Header nection Coin Drop Coin Drop tion Value Present Present Present Present #2 Present #1 Present Table 30 continues... © Copyright, Alliance Laundry Systems LLC - Part No. 807870ENR3 DO NOT COPY or TRANSMIT...
Page 104 Payment Sys- Dipswitch 2 Gravity Drain Heater Ena- tem Present 240 Volt Sup- Configuration (ON) bled (ON) (ON) Energy Cycle ply (ON) Value Table 31 continues... © Copyright, Alliance Laundry Systems LLC - Part No. 807870ENR3 DO NOT COPY or TRANSMIT...
Page 105 (<) keypad. The control will return to the Testing Mode. Testing Mode. Refer to How to Enter Testing Feature at the be- ginning of this section. © Copyright, Alliance Laundry Systems LLC - Part No. 807870ENR3 DO NOT COPY or TRANSMIT...
Page 106 CL v oP is displayed when coin vault switch is open. v CL is displayed when coin vault switch is closed. Table 32 continues... © Copyright, Alliance Laundry Systems LLC - Part No. 807870ENR3 DO NOT COPY or TRANSMIT...
Page 107 The control will not advance to next step until drum is empty. RPM speed displayed Spin Test Machine will attempt to spin up to 1200 RPMs. XXXX Table 32 continues... © Copyright, Alliance Laundry Systems LLC - Part No. 807870ENR3 DO NOT COPY or TRANSMIT...
Page 108 Cycling power to the machine is the only way to resume normal operation and the control will stay in this state indefinitely until that time. Table 32 © Copyright, Alliance Laundry Systems LLC - Part No. 807870ENR3 DO NOT COPY or TRANSMIT...
Page 109 Break-in Alarm Check the service door and coin vault switches. ALArn Error Break-in Alarm Check the service door and coin vault switches. Shutdown Error Table continues... © Copyright, Alliance Laundry Systems LLC - Part No. 807870ENR3 DO NOT COPY or TRANSMIT...
Page 110 (default 15 minutes). In the event of a drain error, the control will turn off all outputs and turn on the Machine Error Tone for 15 seconds. Table continues... © Copyright, Alliance Laundry Systems LLC - Part No. 807870ENR3 DO NOT COPY or TRANSMIT...
Page 111 To clear this error one of the following must occur: the machine must be pow- ered down, the Clear Fatal Error Keys must be pressed, or a Clear Fatal Error Network command must be sent. Table continues... © Copyright, Alliance Laundry Systems LLC - Part No. 807870ENR3 DO NOT COPY or TRANSMIT...
Page 112 If the harness looks fine and the error still occurs, try replacing the drive board or harness. Unpower to clear error. Table continues... © Copyright, Alliance Laundry Systems LLC - Part No. 807870ENR3 DO NOT COPY or TRANSMIT...
Page 113 E d 63 ature Short Error Fatal IPM Temper- Hardware failure. Unpower to clear error. Replace drive board if error persists. E d 64 ature Open Error © Copyright, Alliance Laundry Systems LLC - Part No. 807870ENR3 DO NOT COPY or TRANSMIT...
Page 114 NOTE: The Rapid Advance option must be turned on for Rapid Advance to work. How to Exit Rapid Advance Feature Advance through the cycle until reaching the Ready Mode. © Copyright, Alliance Laundry Systems LLC - Part No. 807870ENR3 DO NOT COPY or TRANSMIT...
Page 115 NORMAL cycle keypad with the other hand. The control will reset to the Ready Mode and clear out the current vend that has been entered. © Copyright, Alliance Laundry Systems LLC - Part No. 807870ENR3 DO NOT COPY or TRANSMIT...
Page 116 Power Fail Reset option, and the Power Fail Reset option is turned on, the control will reset the cycle and lose all vending entered for the cycle. © Copyright, Alliance Laundry Systems LLC - Part No. 807870ENR3 DO NOT COPY or TRANSMIT...
Page 117 The Network Communications feature allows the washer control to communicate with a network. The washer control can be pro- grammed and have its data read without using the keypad. © Copyright, Alliance Laundry Systems LLC - Part No. 807870ENR3 DO NOT COPY or TRANSMIT...
Page 118 Normal & Synthetic = 4:20 Delicate = 4:05 Rinse 3 (Disabled) Fill 2:00 Agitate 0:35 Extract Normal & Synthetic = 4:20 Delicate = 4:05 Table continues... © Copyright, Alliance Laundry Systems LLC - Part No. 807870ENR3 DO NOT COPY or TRANSMIT...
Page 119 Final Extract Extract Normal = 9:50 Synthetic = 8:20 Delicate = 7:20 Shakeout Agitate 0:40 Total Time Normal = 30:00 Synthetic = 28:00 Delicate = 26:00 © Copyright, Alliance Laundry Systems LLC - Part No. 807870ENR3 DO NOT COPY or TRANSMIT...

Alliance Laundry Systems HFNNERSP116CW01 Manual

Quick Links

Need help?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for Alliance Laundry Systems HFNNERSP116CW01

Summary of Contents for Alliance Laundry Systems HFNNERSP116CW01

This manual is also suitable for:

Table of Contents