Alliance Laundry Systems CHM1772C Installation Manual
  1. Manuals
  2. Brands
  3. Alliance Laundry Systems Manuals
  4. Washer
  5. CHM1772C
  6. Installation manual
Alliance Laundry Systems CHM1772C Installation Manual

Alliance Laundry Systems CHM1772C Installation Manual

Cabinet hardmount
Hide thumbs Also See for CHM1772C:
Table of Contents

Advertisement

Quick Links

Download this manual See also: Operation & Maintenance Manual
Washer-Extractors
Cabinet Hardmount
Refer to Page 6 for Model Identification
CHM1772C
CHM1772C
Keep These Instructions for Future Reference.
(If this machine changes ownership, this manual must accompany machine.)
Part No. F8208301R7
www.comlaundry.com
November 2011

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the CHM1772C and is the answer not in the manual?

Questions and answers

Related Manuals for Alliance Laundry Systems CHM1772C

Summary of Contents for Alliance Laundry Systems CHM1772C

  • Page 1 Washer-Extractors Cabinet Hardmount Refer to Page 6 for Model Identification CHM1772C CHM1772C Keep These Instructions for Future Reference. (If this machine changes ownership, this manual must accompany machine.) Part No. F8208301R7 www.comlaundry.com November 2011...

  • Page 3: Table Of Contents

    All rights reserved. No part of the contents of this book may be reproduced or transmitted in any form or by any means without the expressed written consent of the publisher. F8208301 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Safety Information... Explanation of Safety Messages...

  • Page 4: Safety Information

    NOTE: The word “NOTE” is used to communicate installation, operation, maintenance or servicing information that is important but not hazard related. © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Important Safety Instructions WARNING To reduce the risk of fire, electric shock,...
  • Page 5 17. Do not operate the machine without the water reuse plug or water reuse system in place, if applicable. © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT F8208301 18. Be sure water connections have a shut-off valve and that fill hose connections are tight.

  • Page 6: Safety Decals

    © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Be careful around the open door, particularly when loading from a level below the door. Impact with door edges can cause personal injury.

  • Page 7: Operator Safety

    Excessively high water level is evident. c. Machine is not connected to a properly grounded circuit. © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT F8208301 Do not bypass any safety devices in the machine. Operating the machine with severe out-of- balance loads could result in personal injury and serious equipment damage.

  • Page 8: Introduction

    HCN020HY2 HCU020KL2 HCN020HYF HCU020KY2 HCN020KC2 HCU020KYF HCN020KCF HCU020KYV HCN020KCV HCZ020GN2 HCN020KD2 HCZ020HN2 HCN020KDV SCL020GC2 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Introduction Model SCL020GN2 SCN020KNF SCL020HN2 SCN020LC2 SCL020HNF SCN020LCF SCL020JC2 SCN020LCV SCL020JD2 SCN020LD2 SCL020JDF SCN020LX2...
  • Page 9 HCN030KD2 SCL030GN2 HCN030KDV SCL030HN2 HCN030KEF SCL030HNF HCN030KY2 SCL030JC2 HCN030KYF SCL030JCF HCN030KYV SCL030JD2 HCU030GC2 SCL030JDF © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT F8208301 (Continued) SCL030JE2 SCN030KN2 SCL030JEF SCN030KNF SCL030JX2 SCN030LC2 SCL030JXF SCN030LCF SCL030JY2 SCN030LCV SCL030KN2 SCN030LD2...
  • Page 10 HCN040KD2 SCL040GN2 HCN040KDF SCL040HN2 HCN040KDV SCL040HNF HCN040KEF SCL040JC2 HCN040KEV SCL040JD2 HCN040KY2 SCL040JDF HCN040KYF SCL040JE2 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT (Continued) SCL040JEF SCN040LCF SCL040JX2 SCN040LCV SCL040JXF SCN040LD2 SCL040JXV SCN040LDV SCL040KN2 SCN040LE2 SCL040KNF SCN040LY2 SCL040KNV...
  • Page 11 HCU080HXF HCN080KCF HCU080KCF HCN080KCV HCU080KCV HCN080KDF HCU080KYF SCL125KNV UCL125KNV SCN125KNV UCU125KNV SCN125LYV SCN125WYV SCU125KNV © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT F8208301 (Continued) SCL060KN2 SCN060LD2 SCL060KNV SCN060LDV SCL060LE2 SCN060LE2 SCN060GC2 SCN060LY2 SCN060GD2 SCN060LYF SCN060GE2 SCN060LYV...

  • Page 12: Delivery Inspection

    © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Nameplate Location The nameplate is located at the rear of the machine and inside door.
  • Page 13 Max. Load : Schematic : Schematic : 30 - 85 psi, 2 - 5.7 Supply Water: Supply Water: © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT F8208301 Model Number Familiarization Guide Sample Model Number: *CN040GC2OU1D01 Phase Phase...

  • Page 14: Replacement Parts

    For technical assistance, contact your local distributor or contact: Alliance Laundry Systems Shepard Street P.O. Box 990 Ripon, Wisconsin 54971-0990 U.S.A. www.comlaundry.com Phone: +1 (920) 748-3121 +32 56 41 20 54 Wevelgem, Belgium © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT F8208301...

  • Page 15: Specifications And Dimensions

    Wash Cylinder Information Cylinder diameter, in. (mm) Cylinder depth, in. (mm) Cylinder volume, ft. Perforation size, in. (mm) Perforation open area, % © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT F8208301 2 Speed Models (176) (222) (191) (240) 30.5...
  • Page 16 Cylinder Speeds Wash/reverse speed, RPM High extract speed, RPM Centrifugal Force Data Wash/reverse centrifugal force, G High extract centrifugal force, G © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 2 Speed Models (Continued) 11.63 14.34 (295) (364) 14.38...
  • Page 17 200V 240V 380V 415V 480V Electrical heating elements Electrical heat element size, kW © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT F8208301 2 Speed Models (Continued) 0.73 (6.9) 10.4 10.4 Specifications and Dimensions 2.09 (0.84)
  • Page 18 Estimated Building Heat Load HVAC load, BTU/hr. (Kcal./hr.) Drive Train Information Number of motors in drive train Drive motor power, hp (kW) © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT V-Speed and F-Speed Models (175) (226) (191) (245) 34.4...
  • Page 19 Total electrical heating capacity, Input Voltage 200V 240V 380V 415V 480V Electrical heating elements Electrical heat element size, kW © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT F8208301 V-Speed and F-Speed Models (Continued) 0.25 0.25 (0.94) (1.09) (1.29) 0.73 (6.9)
  • Page 20 20, 30, 40, 60 and 80 POUND CAPACITY MACHINES Supply Dispenser Input Power Block Compartment Hot Water Inlet © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Figure 3 Cold Water Inlet Vacuum Breaker Drain Outlet...
  • Page 21 (432 mm) 14.38 in. (365 mm) (660 mm) (38 mm) (1067 mm) (229 mm) © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT F8208301 Machine Capacity Dimensions 38.03 in. (966 mm) (1024 mm) 37.46 in. (951 mm) (1009 mm) 1.81 in.
  • Page 22 51.26 in. (1302 mm) 75.15 in. (1909 mm) 83.4 in. (2118 mm) 2.86 in. (73 mm) © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 125 POUND CAPACITY MACHINES Figure 4 Hot Water Inlet Liquid Chemical Inlet...
  • Page 23 33.03 in. (839 mm) 39.28 in. (998 mm) 60.21 in. (1529 mm) 65.77 in. (1671 mm) 2.29 in. (58 mm) © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT F8208301 125 POUND CAPACITY MACHINES Figure 5 Specifications and Dimensions...

  • Page 24: Dimensional Clearances

    .5 in. (12.5 mm) 24 in. Recommended (610 mm) 12 in. Minimum (305 mm) © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT FRONT Figure 6 Machine Capacity Dimensional Clearances 2 in. 2 in. (51 mm) (51 mm) .5 in.

  • Page 25: Installation

    WARNING To reduce the risk of fire, this appliance must be bolted to an uncovered concrete floor. © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT F8208301 Installation The floor and foundation must be minimum 4000 psi reinforced concrete set firmly in clean, compacted fill dirt.
  • Page 26 Dynamic pressure, lbs.-ft. (kN-m Dynamic load frequency, Hz Maximum moment about machine base, lbs.-ft. (kN-m) Maximum vertical load, lbs. (kN) © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Floor Load Data, 2 Speed Models (1.99) (2.76) 97.8 (4.68) (4.84)

  • Page 27: Concrete Foundation Installation

    .5 in. (13 mm) minimum 4 in. (102 mm) minimum © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT F8208301 1. Verify that the floor meets the requirements given in the Machine Foundation section.
  • Page 28 6. Use the mounting bolt layout to properly position the mounting bolts in the wet concrete. © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT NOTE: When using any anchoring bolts, allow 1.5 inches (38 mm) to extend above the surface of the concrete.
  • Page 29 COMPACTED FILL DIRT 24 in. (609 mm) DEPTH 12 in. (305 mm) 6 in. (152 mm) © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT F8208301 LENGTH FOR ONE MACHINE COMPACTED FILL DIRT 18 in. (457 mm) DEPTH 80 MODELS 47.5 in.

  • Page 30: Machine Anchoring

    Grout completely under all frame members. © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 13. Position washers and nuts on bolts and finger tighten nuts to machine base.

  • Page 31: Elevated Base Frame Installation

    .38 inch (9.5 mm) in 20, 30 and 60 pound models and .25 inch (6.3 mm) in 40 pound models. © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT F8208301 CHM2284...
  • Page 32 Refer to Table 4. © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 17. Position the machine over the base frame, aligning the mounting holes on the machine with the corresponding holes on the frame.

  • Page 33: Mounting Bolt Hole Locations (Without Elevated Base Frames)

    20.88 in. (530 mm) Front of Front Panel 2.56 in. 2.56 in. 20 Models (65 mm) (65 mm) CHM2224N Figure 14 IMPORTANT: Drawing is not to scale. © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT F8208301...
  • Page 34 Mounting Bolt Hole Locations (Without Elevated Base Frames) 2.75 in. (70 mm) 2.56 in. (65 mm) IMPORTANT: Drawing is not to scale. © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 29 in. (737 mm) 23.5 in. (597 mm) 37.52 in.
  • Page 35 (45 mm) (660 mm) Front of Front Panel 30.63 in. 2.32 in. (778 mm) (59 mm) 40 Models CHM206 CHM2067N Figure 16 IMPORTANT: Drawing is not to scale. © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT F8208301...
  • Page 36 Mounting Bolt Hole Locations (Without Elevated Base Frames) 3.28 in. (83 mm) 2.03 in. (52 mm) IMPORTANT: Drawing is not to scale. © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 34.06 in. (865 mm) 27.5 in. (700 mm) 46.88 in.
  • Page 37 4 in. (102 mm) *For close mounting, use mounting bolt pattern labeled “A”; for standard mounting, use “B.” IMPORTANT: Drawing is not to scale. © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT F8208301 33.5 in. (851 mm) 40 in.
  • Page 38 Installation Mounting Bolt Hole Locations (Without Elevated Base Frames) 0.75 in. (19 mm) IMPORTANT: Drawing is not to scale. © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 46.5 in. (1181 mm) 61.5 in. (1562 mm) 55.47 in.

  • Page 39: Mounting Bolt Hole Locations (With Elevated Base Frames)

    20.88 in. (530 mm) Front of Front Panel 2.75 in. 2.75 in. (70 mm) (70 mm) 20 Models CHM2070N Figure 20 IMPORTANT: Drawing is not to scale. © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT F8208301...
  • Page 40 Mounting Bolt Hole Locations (With Elevated Base Frames) 2.94 in. (75 mm) 2.75 in. (70 mm) IMPORTANT: Drawing is not to scale. © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 29.4 in. (747 mm) 23.5 in. (597 mm) 37.52 in.
  • Page 41 2.38 in. Front of Front Panel (61 mm) 30.88 in. (784 mm) 2.44 in. 40 Models (62 mm) CHM2074N Figure 22 IMPORTANT: Drawing is not to scale. © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT F8208301...
  • Page 42 Mounting Bolt Hole Locations (With Elevated Base Frames) (88 mm) 2.22 in. (56 mm) IMPORTANT: Drawing is not to scale. © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 34.5 in. (876 mm) 27.5 in. (700 mm) 46.88 in.

  • Page 43: Drain Connection

    Drain Valve Drain Tee * Drain line must be vented to meet local plumbing codes. © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT F8208301 Use the supplied black rubber adapter and clamps to transition from the machine drain outlet to the 2 inches...
  • Page 44 3 in. (76 mm) 3 in. (76 mm) 4 in. (102 mm) 80, 125 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Refer to Table 5 for capacity-specific drain information. NOTE: Installation of additional machines will require larger drain connections.

  • Page 45: Water Connection Requirements

    2 in. (50 mm) 2 in. (50 mm) 2.5 in. (70 mm) Table 8 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT F8208301 Suitable air cushions should be installed in supply lines to prevent “hammering.” Refer to Figure 26.

  • Page 46: Electrical Installation Requirements

    © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Make sure the correct transformer jumper (208 Volt or 240 Volt) is in place. Refer to the “optional” Electrical...

  • Page 47: Input Power Conditioning

    “stinger leg,” “high leg,” “red leg,” etc. This leg should be identified throughout the system with red or orange tape on the wire at each connection point. The stinger leg should be connected to the center Phase B on the reactor. © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT F8208301 IMPORTANT: Only one device per branch circuit is required.

  • Page 48: Input Voltage Requirements

    IMPORTANT: All quick disconnects should comply with the above specifications. DO NOT use fuses instead of circuit breakers. © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Connection Specifications IMPORTANT: Connection must be made by a qualified electrician using wiring diagram provided with machine, or according to accepted European standards for CE-approved equipment.

  • Page 49: Phase Adder

    Machines can be converted for lower voltage operation and/or 50 Hz operation. Refer to conversion label by serial plate for details. © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT F8208301 Phase Adder IMPORTANT: Do not use a phase adder on any machine.
  • Page 50 7/7/10) 200 – 240 50/60 NOTE: Wire sizes shown are for copper, THHN, 90°C conductor per NEC article 310. © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Electrical Specifications 20 Pound Capacity Models Standard 2 Speed Models...
  • Page 51 (starting 7/7/10) 200 – 240 50/60 NOTE: Wire sizes shown are for copper, THHN, 90°C conductor per NEC article 310. © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT F8208301 Electrical Specifications 30 Pound Capacity Models Standard...
  • Page 52 50/60 200 – 240 50/60 NOTE: Wire sizes shown are for copper, THHN, 90°C conductor per NEC article 310. © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Electrical Specifications 40 Pound Capacity Models Standard 2 Speed Models...
  • Page 53 200-240 50/60 200-240 50/60 NOTE: Wire sizes shown are for copper, THHN, 90°C conductor per NEC article 310. © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT F8208301 Electrical Specifications 60 Pound Capacity Models Standard 2 Speed and Fixed-Speed Models...
  • Page 54 7/7/10) 200 – 240 50/60 NOTE: Wire sizes shown are for copper, THHN, 90°C conductor per NEC article 310. © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Electrical Specifications 80 Pound Capacity Models Standard Variable-Speed Models...

  • Page 55: Steam Requirements (Steam Heat Option Only)

    Maximum pressure Table 16 IMPORTANT: Failure to install the customer supplied steam filter may void the warranty. © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT F8208301 Supply Dispensing Dangerous Chemicals. May damage eyes and skin. Wear eye and hand protection when handling chemicals;...

  • Page 56: External Supplies

    “24VAC” and “RELAY COM”. Do not use the transformer terminals if an external power supply is used. © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT STEP 1: Insert screwdriver & press down 8.5mm...

  • Page 57: Connection Of External Liquid Supplies

    Consult the supply vendor instructions for operational details about supply injections. © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT F8208301 125 Pound OPL Models (With Optional Dispenser) Refer to Figure 32.

  • Page 58: Start Up

    3. For V-speed models, have a qualified electrician reverse any two motor leads at the AC terminal block. © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Start Up F8208301...

This manual is also suitable for:

Hcd020gd2Hcd020jd2Hcd020ld2Hcl020gd2Hcl020gn2Hcl020hdf ... Show all

Table of Contents

Save PDF