Related Manuals for Infineon XE166 Easy Kit
Summary of Contents for Infineon XE166 Easy Kit
- Page 1 X E166 Ea sy K it Boa rd M anual, V.1.0, Nov. 2008 X E 1 6 6 F a m i l y E a s y K i t B o a r d R E V . V 3 . 1 M i c r o c o n t ro l le r s N e v e r s t o p...
- Page 2 Infineon Technologies Components may only be used in life-support devices or systems with the express written approval of Infineon Technologies, if a failure of such components can reasonably be expected to cause the failure of that life-support device or system, or to affect the safety or effectiveness of that device or system. Life support devices or systems are intended to be implanted in the human body, or to support and/or maintain and sustain and/or protect human life.
- Page 3 Any information within this document that you feel is wrong, unclear or missing at all? Your feedback will help us to continuously improve the quality of this document. Please send your proposal (including a reference to this document) to: mcdocu.comments@infineon.com XE166 Easy Kit Board Manual V 1.0, 2008-11...
-
Page 4: Table Of Contents
Introduction - XE166 family ........5 General Information about XE166 Easy Kit Board ....6 Summary of Features . -
Page 5: Introduction - Xe166 Family
RAM, strongly enhanced peripherals and a complete DSP library. MCU and DSP in a core Infineon Technologies´ Real Time Signal Controller combines the traditional strengths of a Microcontroller Unit (MCU) to control peripherals with the computing power of Digital Signal Processors (DSP). -
Page 6: General Information About Xe166 Easy Kit Board
XE166 Family Easy Kit Manual General Information about XE166 Easy Kit Board General Information about XE166 Easy Kit Board Summary of Features – Infineon’s XE166 Controller in TQFP144/100/64 Pin Package – High Speed CAN Transceivers, LIN Transceiver, USB to UART/JTAG bridge –... -
Page 7: Block Diagram
General Information about XE166 Easy Kit Board Block Diagram Voltage Regulator CAN Transceiver LIN Transceiver EEPROM XE166 8 LEDs USB To UART/ JTAG Bridge XTAL Figure 1 Block diagram of XE166 Easy Kit layout overview XE166 Easy Kit Board Manual V 1.0, 2008-11... -
Page 8: Board Overview
XE166 Family Easy Kit Manual General Information about XE166 Easy Kit Board Board Overview P10.0 P10.7 OCDS1 Config Infineon Reset XE166 Debug Debug Active CAN2 Reset Power supply CAN1 Power supply Power LIN1 AN 0 ( ADC0) Jumper Figure 2... - Page 9 XE166 Family Easy Kit Manual General Information about XE166 Easy Kit Board R112 C101 R145 X107 X204 R147 R226 R150 R120 R122 R123 CB216 R153 CB104 CB221 R144 R121 R157 R252 CB215 R146 R151 R111 R152 R148 1 2 3 4 5...
-
Page 10: Dip Switch S102
XE166 Family Easy Kit Manual General Information about XE166 Easy Kit Board DIP Switch S102 Although most of the programmable features of the XE166 are selected by software either during the initialization phase or repeatedly during program execution, some features must be selected earlier because they are used for the first access of the program execution. -
Page 11: Basic Startup Configuration For Xe166Fm
XE166 Family Easy Kit Manual General Information about XE166 Easy Kit Board 2.4.2 Basic Startup Configuration for XE166FM Table 3 Basic Startup Configuration with debug support Startup Mode Debug CFG pins P10 [3:0] TRST=1 Interface Internal Start from Flash JTAG pos.B DAP pos.1... -
Page 12: Usb Driver Installation
Additionally a driver for a virtual COM port will be installed. Find out more about DAS on the Infineon Web page: http://www.infineon.com/DAS This DAS Software can be found on the Easy Kit CD under Tools. A DAS Software Version 2.6.1 or higher need to be used for the Easy Kit. -
Page 13: Easy Kit Power Supply Concept
XE166 Family Easy Kit Manual General Information about XE166 Easy Kit Board Easy Kit Power Supply concept The Easy Kit USB Power Supply concept enables the user to work with the Kit without an external Power Supply. If the USB power supply is not sufficient an additional regulated DC power supply can be used. -
Page 14: Power Supply Via Power Plug
XE166 Family Easy Kit Manual General Information about XE166 Easy Kit Board The USB specification provides a 5 V supply on a single wire from which connected USB devices may draw power. The specification provides for no more than 5.25 V and no less than 4.35 V between the +ve and -ve bus power lines. -
Page 15: Information In Detail
• Debug-related - either debugging will be possible, and if Yes - which debug-interface to use (JTAG, DAP, selectable pin-assignments). The Easy Kit Board Manual covers only a limit numbers of start-up modes. For all possible start-up modes please refer to the corresponding user manual. XE166 Easy Kit Board Manual V 1.0, 2008-11... -
Page 16: Switch S102
Bootstrap loader ASC ON-OFF-OFF-xx-xx S102 Startup configuration: Enhanced bootstrap loader ASC ON-OFF-ON-xx-xx S102 Startup configuration Bootstrap loader CAN OFF-ON-OFF-xx-xx S102 Startup configuration Bootstrap loader SSC OFF-ON-ON-OFF-xx S102 Startup configuration All other positions are reserved XE166 Easy Kit Board Manual V 1.0, 2008-11... -
Page 17: Dip Switch Setting Xe166Fm
DAP Debug Mode (Pos.1) ON-ON-OFF-xx-ON S102 Startup configuration: JTAG Debug Mode (Default) OFF-OFF-OFF-xx-ON S102 Startup configuration: Bootstrap loader CAN OFF-ON-OFF-OFF-ON S102 Startup configuration: Bootstrap loader SSC OFF-ON-ON-OFF-ON S102 Startup configuration All other positions are reserved XE166 Easy Kit Board Manual V 1.0, 2008-11... -
Page 18: Headers, Connectors And Components
Note: If the Board is equipped with a XE162FM in a 64 Pin package the CAN2 interface is disabled. To enable remove R238 and solder R136. In this case Usic 0 channel 0 is not avalible on Pin 2.4 . XE166 Easy Kit Board Manual V 1.0, 2008-11... -
Page 19: Lin Interface (X104)
(ACTIV LED is off) and on the DAP connector (X204) is no hardware connected or the hardware is tristated. If the ACTIV LED is on, then stop the active DAS Server JTAG over USB Chip and/or remove the USB connection to the PC. XE166 Easy Kit Board Manual V 1.0, 2008-11... -
Page 20: Dap Interface
10. You can connect a DAP hardware here. If you use this connector make sure that the MiniWiggler is not activ (ACTIV LED is off) and a connected OCDS1 hardware is disconnected or tristated. VREF DAP1 DAP0 USER0_IO USER1_IN /RESET Figure 10 On-board header X204 XE166 Easy Kit Board Manual V 1.0, 2008-11... -
Page 21: Adc
P2.5 (SCK) replace R143 with R144 P10.0 (SI) with R145 P2.4 (SI) replace R145 with R146 P10.7 (SO) with R147 P2.3 (SO) replace R147 with R148 P2.7 (CS) with R149 P2.6 (CS) replace R149 with R150 XE166 Easy Kit Board Manual V 1.0, 2008-11... -
Page 22: Pin Definition And Location
P2.7 AGND P5.0 P4.6 P5.1 P4.5 P5.2 P0.0 P5.3 DDPB DDPB Figure 11 Pinout of the144 Pin device Note: (1) For the XE166FM Series the Tref pin has been replaced by P2.13. XE166 Easy Kit Board Manual V 1.0, 2008-11... - Page 23 VDDPB P8.4 P7.0 P7.1 P8.0 P6.1 VDDPA P15.2 P15.5 P5.0 P5.3 VAREF2 P7.2 P8.3 P8.2 P8.1 P6.0 P6.3 P15.1 P15.4 P15.7 VAGND P5.2 X105 Figure 12 Pin connector of the144 pin device XE166 Easy Kit Board Manual V 1.0, 2008-11...
-
Page 24: Xe164F/Xe164Fm - 100 - Pinout
P2.9 P2.8 AREF P0.1 AGND P5.0 P2.7 P5.2 P0.0 P5.3 Figure 13 Pinout of the 100 pin device Note: (1) For the XE166FM Series the Tref pin has been replaced by P2.13. XE166 Easy Kit Board Manual V 1.0, 2008-11... - Page 25 VDDIM P6.2 P15.0 P15.6 P5.1 /TESTM VDDPB VAREF1 P7.0 P7.1 P6.1 P15.2 P15.5 P5.0 P5.3 VDDPB VDDPA P7.2 P6.0 P15.4 VAGND P5.2 X105 Figure 14 Pin connector of the 100 pin device XE166 Easy Kit Board Manual V 1.0, 2008-11...
-
Page 26: Xe162Fm - 64 - Pinout
XE166 Family Easy Kit Manual Information in Detail 3.3.3 XE162FM - 64 - Pinout Figure 15 Pinout of the 64 pin device XE166 Easy Kit Board Manual V 1.0, 2008-11... -
Page 27: Zero Ohm Resistors
R143 / R145 connect to USIC1 Channel1 R147 / R149 connect to USIC1 Channel1 R144 / R146 connect to SSC bootstrap loader (U0C0) R148 / R150 connect to SSC bootstrap loader (U0C0) XE166 Easy Kit Board Manual V 1.0, 2008-11... - Page 28 ASC Bootloader: 144Pin / 100 Pin R236-R237 assembled with 0R R238-R239 open Other R236-R237 open R238-R239 assembled with 0R U203: R210 For internal use only EEPROM 93LC46B: R207 If ORG functionality is needed XE166 Easy Kit Board Manual V 1.0, 2008-11...
-
Page 29: Getting Started
Easy Kit Manual Getting Started Getting Started For the successful start up of the XE166 Easy Kit, the following items should be done: Figure 16 XE166 Easy Kit (144-Pin) By default a HELLO WORLD program can be executed. The following steps are needed to be successful. -
Page 30: Power Supply
By default one green LED should be active. It indicates that the embedded voltage regulator supply the microcontroller. Please Note, the power supply is not part of the delivery ! Figure 18 Power Supply Connector XE166 Easy Kit Board Manual V 1.0, 2008-11... -
Page 31: Ocds Debugging Interface
Getting Started OCDS Debugging Interface The XE166 Easy Kit offers two types of JTAG interfaces. With the FTDI chip an on board USB JTAG wiggler has been implemented. Further the USB interface allows to emulate a USB to UART bridge. Both can be done at the same time. -
Page 32: Schematic
XE166 Family Easy Kit Manual Schematic Schematic XE166 Easy Kit Board Manual V 1.0, 2008-11... - Page 33 XE166 Family Easy Kit Manual Schematic XE166 Easy Kit Board Manual V 1.0, 2008-11...