Page 1
Eva lua t io n Bo ar d For XMC4000 Family X MC440 0 P lat fo r m2 G o Kit Version 1.1 Board Us er ‘s Ma nu al Revision 2019-08-30 M ic ro con tr o lle r...
Page 2
Infineon Technologies components may be used in life-support devices or systems only with the express written approval of Infineon Technologies, if a failure of such components can reasonably be expected to cause the failure of that life-support device or system or to affect the safety or effectiveness of that device or system.
Page 3
XMC4400 Platform2Go Series-V1.1 Revision History Page or Item Subjects (major changes since previous revision) Revision 2019-08- Initial Version Trademarks of Infineon Technologies AG AURIX™, C166™, CanPAK™, CIPOS™, CIPURSE™, EconoPACK™, CoolMOS™, CoolSET™, CORECONTROL™, CROSSAVE™, DAVE™, EasyPIM™, EconoBRIDGE™, EconoDUAL™, EconoPIM™, EiceDRIVER™, eupec™, FCOS™, HITFET™, HybridPACK™, I²RF™, ISOFACE™, IsoPACK™, MIPAQ™, ModSTACK™, my-d™, NovalithIC™, OptiMOS™, ORIGA™, PRIMARION™, PrimePACK™, PrimeSTACK™,...
XMC4400 Platform2Go Series-V1.1 Table of Contents Table of Contents Introduction ..........................6 Key Features ............................7 Block Diagram ............................8 Hardware Description ....................... 8 Power Supply ............................. 11 Pin Header for Microbus and Shield2Go Connector 1 and 2 ............. 13 Solderable 0 Ohm Pin Bridges ......................
Page 5
XMC4400 Platform2Go Series-V1.1 Table of Contents Figure 12 XMC4400 Schematic: USB connector, Microcontroller pins and power, .......... 22 Figure 13 ICs and Power Schematic: Can Transceiver, RTC Battery, Power ............23 Figure 14 Geometry ............................24 List of Tables Table 1 Kit Specification ...........................
ARM Cortex It can be used with a wide range of development tools including Infineon’s free of charge Eclipse based IDE DAVE. The XMC4400 Platform2Go Series-V1.1 are designed to evaluate the capabilities of the XMC4400 Microcontroller. Table 1 shows its specification.
XMC4400 Platform2Go Series-V1.1 Introduction The Ethernet-communication is not supported by the XMC4400 Platform2Go Lite Kit, because some components e.g. for Ethernet are not assembled. All boards are marked with “Platform2Go XMC4400-V1.1” and can be distinguished by the assembled devices (see pictures in chapter 2). These boards are neither cost nor size optimized and do not serve as a reference design.
Two 40-pin header X1 and X2 Connection Header for Arduino mikroBUS™ connector Two Infineon Shield2Go connectors (at the bottom of the board) Potentiometer (10kOhm) On-board power generation 2 User Push-Buttons, 2 User LEDs, Reset Push-Button ...
XMC4400 Platform2Go Series-V1.1 Hardware Description Power Supply The XMC4400 Platform2Go Series-V1.1 must be supplied by an external 5 Volt DC power supply connected to any of the micro USB plugs (X100, X101). The green Power LED (VDD3.3) indicates the presence of the generated 3.3 V supply voltage.
XMC4400 Platform2Go Series-V1.1 Hardware Description Pin Header X1 and X2 The pin headers X1 and X2 can be used to extend the evaluation board or to perform measurements on the XMC4400. Figure 7 shows the available GPIOs / signals at these pin headers. The pin table is also printed onto the bottom side of the PCB in bottom view.
XMC4400 Platform2Go Series-V1.1 Hardware Description Pin Header for Microbus and Shield2Go Connector 1 and 2 The pin header for Microbus and Shield2Go Connector 1 and 2 can be used to extend the evaluation board or to perform measurements on the XMC4400. Figure 8 shows the available signals at these pin headers. The Shield2Go pin header is mounted on the bottom.
XMC4400 Platform2Go Series-V1.1 Hardware Description Solderable 0 Ohm Pin Bridges The 0 Ohm (0805) pin bridges enable/disable the signal pins in Table 3 (enabled by default). To disable the signals, their resistor has to be removed. The XMC4400 pins are then usable for other usages. Table 3 Signal mapping of the 0 Ohm Pin Bridges Resistor...
XMC4400 Platform2Go Series-V1.1 Hardware Description Arduino Compatible Connector The mapping of GPIOs and XMC™ pin functions to Arduino compatible functions can be found in Figure 9. The Arduino compatible connector supports SPI interface (SPI_xxx) I2C interface (I2C_xxx) UART interface (UART_xxx) ...
XMC microcontroller families to simplify and shorten SW development. It can be downloaded at www.infineon.com/dave. The latest Segger J-Link Driver can be downloaded at http://www.segger.com/jlink-software.html. Table 6 shows the pin assignment of the XMC4400 used for debugging and UART communication.
2.10 CAN Transceiver The XMC4400 Platform2Go provides a CAN interface via the X3 connector. Infineon’s high speed CAN transceiver IFX1051LE for industrial application supports 3.3V I/O logic and is suitable for 12V and 24V bus systems with an excellent EMC performance. The CAN bus (signals CANH, CANL) is not terminated by a 120Ohm and needs to be terminated externally.
XMC4400 Platform2Go Series-V1.1 Hardware Description 2.11 Serial Flash Memory The XMC4400 Platform2Go provides a 32 Mbit serial flash memory from Microchip Technology (type: SST26VF032BT-104I/SM) interfaced to XMC4400 through a SPI interface. The SPI interface can be configured as single, dual or quad SPI. To use the Serial Flash Memory pins otherwise see also Table 3. Table 9 XMC4400 Pins Mapping for Serial Flash Memory XMC Pin...
XMC4400 Platform2Go Series-V1.1 Production Data 2.13 Boot Option During power-on-reset the XMC4400 latches the signal level at the pins TMS and TCK. Based on the logic levels latched at these pins after reset the XMC4400 starts booting in different modes. TMS and TCK pins are used for debugging and by default program execution is always starting from on-chip flash (normal mode).
Page 22
XMC4400 Platform2Go Series-V1.1 Production Data Figure 12 XMC4400 Schematic: USB connector, Microcontroller pins and power, Potentiometer Buttons and LEDs Board Users Manual Revision 2019-08-30...
Page 23
XMC4400 Platform2Go Series-V1.1 Production Data C133 10uF C132 10uF Figure 13 ICs and Power Schematic: Can Transceiver, RTC Battery, Power Board Users Manual Revision 2019-08-30...
Page 24
XMC4400 Platform2Go Series-V1.1 Production Data Figure 14 Geometry Board Users Manual Revision 2019-08-30...
XMC4400 Platform2Go Series-V1.1 Production Data List of Material The list of material is valid for the Platform2Go XMC4400 Lite/3.3V/5V. Table 12 List of Material Description Designator Value Quantity PackageReference fitted Micro Miniature BUTTON1 P3.1, FSM2JSMA Pushbutton Switch BUTTON2 P3.2, RESET 7451 / 2920 220uF Solid Tantalum...
Page 27
XMC4400 Platform2Go Series-V1.1 Production Data For Power Lines; For L100, L101, 0603 / 1608 General L102, L103 For Power Lines; For L400, L401 0603 / 1608 General LED1 P0.6, LED2 P0.7 mikroBUS Host MIKROBUS Socket 9 Pin of the Socket Headers 'S2G-1P, S2G-1P-2 8 Pin of the Socket...
Page 28
XMC4400 Platform2Go Series-V1.1 Production Data Standard Thick Film R300, R302 0402 / 1005 Chip Resistor Automotive Grade R123, R124 0603 / 1608 680R Thick Film Chip Resistor Standard Thick Film R126 0402 / 1005 4.7k Chip Resistor Standard Thick Film R400, R402 0402 / 1005 Chip Resistor...
Page 29
XMC4400 Platform2Go Series-V1.1 Production Data Through hole .025'' X302 TSW-108-23-F-S SQ Post Header, 2.54mm pitch, 8 pin, vertical, single row Through hole .025'' X303 TSW-108-07-L-S SQ Post Header, 2.54mm pitch, 8 pin, vertical, single row X304 TSW-110-07-L-S Through hole .025'' SQ Post Header, 2.54mm pitch, 10 pin, vertical, single row...
Page 30
. i n f i n e o n . c o m Published by Infineon Technologies AG...