Transition Networks E-FRL-MC01A Installation Manual

FCC Regulations
NOTE: This equipment has been tested and found to comply with the limits for a Class A
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference when the equipment is operated in a
commercial environment. This equipment generates, uses, and can radiate radio frequen-
cy energy and, if not used in accordance with the instruction manual, may cause harmful
interference to radio communications. Operation of this equipment in a residential area is
likely to cause harmful interference in which case the user will be required to correct the
interference at his own cost.
NOTE: This digital apparatus does not exceed the Class A limits for radio noise for digital
apparatus set out on the radio Interference regulations of the Canadian Department of
Communications.
Trademarks
TRANSITION Networks and the Micro-ceiver are trademarks of TRANSITION Networks,
Inc.
Ethernet is a registered trademark of the Xerox Corporation, Inc.
ST is a registered trademark of AT&T.
Apple is a registered trademark of Apple Computer, Inc.
Technical Support
For more information about this product or other TRANSITION Networks
products call your local TRANSITION Networks distributor. Or contact us directly:
Phone: (612) 941-7600
Fax: (612) 941-2322
Toll Free Tech Support Line: (800) 260-1312
P/N 7319.A
FCC Regulations
NOTE: This equipment has been tested and found to comply with the limits for a Class A
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference when the equipment is operated in a
commercial environment. This equipment generates, uses, and can radiate radio frequen-
cy energy and, if not used in accordance with the instruction manual, may cause harmful
interference to radio communications. Operation of this equipment in a residential area is
likely to cause harmful interference in which case the user will be required to correct the
interference at his own cost.
NOTE: This digital apparatus does not exceed the Class A limits for radio noise for digital
apparatus set out on the radio Interference regulations of the Canadian Department of
Communications.
Trademarks
TRANSITION Networks and the Micro-ceiver are trademarks of TRANSITION Networks,
AAUI to Fiber Optic FOIRL Ethernet
Micro-ceiver

Installation Guide

About the Fiber Optic Micro-ceiver
The TRANSITION Networks AAUI to fiber optic Micro-ceiver™ P/N E-FRL-MC01A is a compact
unit used in an Ethernet IEEE 802.3 type of network. It can be connected directly to any AAUI (Apple
Attacment Unit Interface) port on a workstation or printer.
The Micro-ceiver™ complies with the Ethernet IEEE 802.3 specifications for a fiber optic inter-
repeater link (FOIRL).
The Micro-ceiver has an AAUI (14 - Pin) port interface on one end and two ST type fiber connec-
tions on the other. (An SMA type fiber connection is also available: Transition P/N E-FRL-MC01A(SMA).
ON
AAUI
Connector
Dimensions: Case size: 2.45" (6.2cm) x 1.75" (4.4cm) x 0.875" (2.2cm)
The AAUI cable length is 0.5 meters or 1.65 feet.
7090 Shady Oak Road
Eden Prairie, MN 55344
AAUI to Fiber Optic FOIRL Ethernet
Micro-ceiver
Installation Guide
About the Fiber Optic Micro-ceiver
The TRANSITION Networks AAUI to fiber optic Micro-ceiver™ P/N E-FRL-MC01A is a compact
unit used in an Ethernet IEEE 802.3 type of network. It can be connected directly to any AAUI (Apple
(Transceiver)
™
™
OFF
RX
Ethernet
SQE
FOIRL to AAUI
Transceiver
# E-FRL-MC01A
Jabber
Collision
TX
Link
Power
(Transceiver)
™
™