Grandstream Networks GWN76 Series User Manual page 69

Wi-fi access points
Hide thumbs Also See for GWN76 Series:
Table of Contents

Advertisement

Configures the frequency of DTIM (Delivery Traffic Indication Message) transmission per each
beacon broadcast. Clients will check the AP for buffered data at every configured DTIM Period.
DTIM Period
You may set a high value for power saving consideration.  Default value is 1, meaning that AP will
have DTIM broadcast every beacon. If set to 10, AP will have DTIM broadcast every 10 beacons.
Valid range: 1 – 10.
Configure the limit for wireless client. If there is an SSID per-radio on a LAN, each SSID will have
Wireless Client Limit
the same limit. So, setting a limit of 50 will limit EACH ssid to 50 users independently. Note: If set
to 0, it equals disable the limit.
AP will remove the client's entry if the client generates no traffic at all for the specified time
Client Inactivity
period. The client inactivity timeout is set to 300 seconds by default. Range from 60-3600
Timeout(s)
seconds.
Configures the client bridge support to allow the access point to be configured as a client for
ridging wired only clients wirelessly to the network. When an access point is configured in this
Client Bridge Support
way, it will share the Wi-Fi connection to the LAN ports transparently. Once an SSID has Client
Bridge Support enabled, the AP adopted in this SSID can be turned in to Bridge Client mode by
click the Bridge button. Note: This feature is not supported on GWN7602.
Client Time Policy
Select a time policy to be applied to all clients connected to this SSID.
When set to "Disable": all of the broadcast and multicast packages will be forwarded to the
Multicast/Broadcast
wireless interface. When set as "Enabled": all of the broadcast and multicast packages will be
Suppression
discarded except DHCP/ARP/IGMP/ND; When set to "Enable with Proxy ARP enabled": AP will
enable the optimization with Proxy ARP enabled in the meantime.
When set to "Disabled": none of the multicast package will be converted; Passive mode: AP will
Convert IP multicast
never initiatively broadcast IGMP queries, and the IGMP snooping item will be aged out 300
to unicast
seconds after it is registered, which may result in the failure of forwarding multicast data. Active
mode: AP will initiatively broadcast IGMP queries to keep updating of the IGMP snooping items.
Enable Schedule
Enable this option to assign a schedule for the bandwidth rule.
Schedule
Within the time of schedule, SSID can be used.
Check to enable/disable Voice Enterprise. The roaming time will be reduced once enable voice
enterprise.
• The 802.11k standard helps clients to speed up the search for nearby APs that are available as
roaming targets by creating an optimized list of channels.
• When the signal strength of the current AP weakens, your device will scan for target APs from
this list. When your client device roams from one AP to another on the same network, 802.11r
Enable Voice
uses a feature called Fast Basic Service Set Transition (FT) to authenticate more quickly. FT works
Enterprise
with both pre-shared key (PSK) and 802.1X authentication methods.
• 802.11v allows client devices to exchange information about the network topology, including
information about the RF environment, making each client network aware, facilitating overall
improvement of the wireless network.
Note: 11R is required for enterprise audio feature, 11V and 11K are optional. This field is available
only when "Security Mode" is set to "WPA/WPA2" or "WPA2".
Check to enable 802.11r. This field is available only when "Security Mode" is set to "WPA/WPA2" or
Enable 11R
"WPA2".
Enable 11K
Check to enable 802.11k
Enable 11V
Check to enable 802.11v
This option will enable GWN AP to answer the ARP requests from its LAN for its connected Wi-Fi
ARP Proxy
clients. This is mainly to reduce the airtime consumed by ARP Packets
This option will allow the user to enable/disable the Unscheduled Automatic Power Save Delivery
U-APSD
feature.
Once enabled, the client Bonjour on the SSID is forwarded to the VLAN of the Bonjour service
Enable Bonjour
(such as Samba). Supported on GWN7605, GWN7605LR, GWN7615, GWN7630, GWN7630LR,
Gateway
GWN7660, GWN7660LR
Wi-Fi

Advertisement

Table of Contents
loading

This manual is also suitable for:

Gwn7630lrGwn7605lrGwn7660lrGwn7664lr

Table of Contents