Table of Contents
Advertisement
Quick Links
User's Manual
MIL-S2612, 2-port 100BASE-FX Module (ST)
MIL-S2613, 2-port 100BASE-FX Module (SC)
MIL-S2614, 2-port 100BASE-FX Module (MT-RJ)
MIL-S2615, 2-port 100BASE-FX Module (VF-45)
MIL-S2622, 4-port 100BASE-FX Module (ST)
MIL-S2623, 4-port 100BASE-FX Module (SC)
MIL-S2624, 4-port 100BASE-FX Module (MT-RJ)
MIL-S2625, 4-port 100BASE-FX Module (VF-45)
MIL-S3630, 8-port 10/100BASE-TX Module (RJ-45)
MIL-S6603SX, 1-port 1000BASE-SX Module (SC)
MIL-S6603LX, 1-port 1000BASE-LX Module (SC)
Advertisement
Table of Contents
Related Manuals for MiLAN MIL-S2612
Summary of Contents for MiLAN MIL-S2612
- Page 1 User’s Manual MIL-S2612, 2-port 100BASE-FX Module (ST) MIL-S2613, 2-port 100BASE-FX Module (SC) MIL-S2614, 2-port 100BASE-FX Module (MT-RJ) MIL-S2615, 2-port 100BASE-FX Module (VF-45) MIL-S2622, 4-port 100BASE-FX Module (ST) MIL-S2623, 4-port 100BASE-FX Module (SC) MIL-S2624, 4-port 100BASE-FX Module (MT-RJ) MIL-S2625, 4-port 100BASE-FX Module (VF-45)
- Page 2 ! DIP Switch for decision connection mode with other network devices 1-2. DIP Switch with Link Mode The 8 port 10/100Base-TX module provides dip switch for 1 to 4 port to adjust link mode with other network devices. Another 4 ports use auto-negotiation protocol only.
- Page 3 When installed into a Switch hub, this Module provides a 100Mbps Fast Ethernet fiber port which can be used to: " Connect the Switch to the backbone of your network; that is, to a basement switch, hub or router " Connect the Switch to a 100Mbps server or end-station 2-1.
- Page 4 Module at-a glance. A DIP-switch sets the operating mode to half-duplex or full-duplex (default). P ort 1 P ort 2 Figure 4. Dip switch location and mode settings The following Table 2. lists the ports’ operating modes based on the DIP switch position. PORT 1 Half-Duplex Full-Duplex Table 2.
- Page 5 When installed into a Switch hub, this Module provides 4 x 100Mbps Ethernet fiber ports which can be used to: " Connect the Switch to the backbone of your network; that is, to a basement switch, hub or router. " Connector the Switch to a 100Mbps server or end station.
- Page 6 The following Table 3. lists the ports operating modes based on the DIP switch position. PORT 1 Half-Duplex Full-Duplex Table 3. Four ports 100Base-FX Fiber Module DIP switch functions 3-3. LED Descriptions There are two LED indicators for each of the Fiber connection ports. If there is no connection to a port, the corresponding LED indicators are not lit.
- Page 7 If you adjust to Enable N-Way, then the DIP for Half-Duplex and Full-Duplex is not effective. If you adjust to Disable N-Way, then the DIP for Half-Duplex and Full- Duplex is effective. The following Table 4. lists the ports’ operating modes based on the DIP switch position. Disable N-way Enable N-way Table 4.
Need help?
Do you have a question about the MIL-S2612 and is the answer not in the manual?
Questions and answers