Subscribe to Our Youtube Channel
Related Manuals for MiLAN MIL-SM8TAF1GPA
Summary of Contents for MiLAN MIL-SM8TAF1GPA
-
Page 1: Management Guide
7 10/100/1000BASE-T (RJ-45) Ports Plus 1 Combination (RJ-45/SFP) Ports MIL-SM8TAF1GPA Management Guide... - Page 3 Trademarks The MiLAN logo and Transition Networks trademarks are registered trademarks of Transition Networks in the United States and/or other countries. To Contact Transition Networks...
- Page 4 You can reach Transition Networks technical support at: E-mail: techsupport@transition.com Telephone: +1.800.260.1312 x 200 Fax: +1.952.941.2322 Transition Networks 10900 Red Circle Drive Minnetonka, MN 55343 United States of America Telephone: +1.800.526.9267 Fax: +1.952.941.2322 http://www.milan.com info@transition.com © Copyright 2008 Transition Networks...
-
Page 5: Table Of Contents
Contents Chapter 1: Introduction Description of Software Features Chapter 2: Initial Configuration Chapter 3: Configuring the Switch Using the Web Interface Navigating the Web Browser Interface Home Page Configuration Options Panel Display Main Menu Web Configuration Displaying Status Overview Showing Port Statistics Displaying the System Name Setting the Switch’s IP Address Configuring the Logon Password... - Page 6 Contents Management Information Bases Appendix B: Troubleshooting Forgot or Lost Password Changing a PC’s IP Address...
- Page 7 Tables Tables Table 3-1 Web Page Configuration Buttons Table 3-2 Switch Main Menu Table 3-3 Port Statistics...
- Page 8 Tables...
- Page 9 Figures Figures Figure 3-2 Front Panel Indicators Figure 3-3 Switch Information Figure 3-4 Port Statistics Figure 3-5 System Name Figure 3-6 LAN Settings 3-10 Figure 3-7 Password Settings 3-11 Figure 3-8 Reset to Factory Defaults 3-12 Figure 3-9 Upgrade Firmware 3-12 Figure 3-10 Upload/Download Configuration 3-13...
- Page 10 Figures...
-
Page 11: Chapter 1: Introduction
Chapter 1: Introduction The MIL-SM8TAF1GPA is a web-managed Gigabit PoE switch that delivers performance and control to your network. It provides 8 full-duplex 1000BASE-T ports that significantly improve network performance and boost throughput using features configured through a web-based management interface. With 16 Gigabits of throughput bandwidth, this switch provides an effective solution to meeting the growing demands on your network. - Page 12 Introduction Broadcast Storm Control – Broadcast suppression prevents broadcast traffic from overwhelming the network. When enabled on a port, the level of broadcast traffic passing through the port is restricted. If broadcast traffic rises above a pre-defined threshold, it will be throttled until the level falls back beneath the threshold. Static Addresses –...
-
Page 13: Chapter 2: Initial Configuration
Chapter 2: Initial Configuration To make use of the management features of your MIL-SM8TAF1GPA, you must first configure it with an IP address that is compatible with the network it is being installed in. This should be done before you permanently install the switch in the network. - Page 14 Initial Configuration...
-
Page 15: Chapter 3: Configuring The Switch
Chapter 3: Configuring the Switch Using the Web Interface This switch provides an embedded HTTP web agent. Using a web browser you can configure the switch and view statistics to monitor network activity. The web agent can be accessed by any computer on the network using a standard web browser (Internet Explorer 5.5 or above, or Mozilla Firefox 1.0 or above). -
Page 16: Table 3-1 Web Page Configuration Buttons
Configuring the Switch Figure 3-1 Home Page Configuration Options Configurable parameters have a dialog box or a drop-down list. Once a configuration change has been made on a page, be sure to click on the Apply button to confirm the new setting. The following table summarizes the web page configuration buttons. -
Page 17: Table 3-2 Switch Main Menu
Navigating the Web Browser Interface Panel Display The web agent displays an image of the switch’s ports. The port will turn green when the corresponding front-panel port is in connection with another device. To show the port number, place mouse pointer onto the intended port. Figure 3-2 Front Panel Indicators Main Menu Using the onboard web agent, you can define system parameters, manage and... - Page 18 Configuring the Switch Table 3-2 Switch Main Menu (Continued) Menu Description Page TRUNKS 3-17 Membership Selects ports to group into static trunks. 3-18 Settings Configures trunk connection settings. 3-18 LACP Setup Configures Link Aggregation Control Protocol (LACP) 3-19 on the switch. LACP Status Shows the LACP groups status.
-
Page 19: Web Configuration
Web Configuration Web Configuration Displaying Status Overview You can easily identify the system by displaying the device name, location and contact information. Field Attributes System Information • System Name – Name assigned to the switch system. • Number of Ports – Number of built-in ports. •... - Page 20 Configuring the Switch • Frame Type – Either “Tagged” or “All.” “Tagged” means that the port will only receive VLAN-tagged frames. When set to “All,” the port will also receive untagged frames. • PVID – The VLAN ID assigned to untagged frames received on the interface. Outgoing frames are tagged unless the frame’s VLAN ID is the same as the PVID.
-
Page 21: Figure 3-3 Switch Information
Web Configuration Web – Click STATUS, Overview. Figure 3-3 Switch Information... -
Page 22: Table 3-3 Port Statistics
Configuring the Switch Showing Port Statistics You can display statistics on network traffic from the ports. These statistics can be used to identify potential problems with the switch (such as a faulty port or unusually heavy loading). All values displayed have been accumulated since the last system reboot, but can be reset to zero by clicking the CLEAR button. -
Page 23: Displaying The System Name
Web Configuration Displaying the System Name You can easily identify the system by displaying the device name. Field Attributes • Switch Name – A name assigned to the switch system. Web – Click System, Name. Figure 3-5 System Name Setting the Switch’s IP Address This section describes how to configure an initial IP interface for management access over the network. -
Page 24: Figure 3-6 Lan Settings
Configuring the Switch Manual Configuration Web – Click SYSTEM, LAN Settings. Enter the IP address, subnet mask and gateway, then click APPLY. Note that if you change the switch IP address, you must close the web interface and start a new session using the new IP address. Figure 3-6 LAN Settings 3-10... -
Page 25: Configuring The Logon Password
Web Configuration Configuring the Logon Password The administrator has write access for all parameters governing the onboard agent. You should therefore assign a new administrator password as soon as possible, and store it in a safe place. Field Attributes • Password – Specifies the user password. (Range: 1-16 characters plain text, case sensitive) Note: If you cannot remember the password, you can restore the original settings by... -
Page 26: Figure 3-8 Reset To Factory Defaults
Configuring the Switch Web – Click System, Tools, Reset to Factory Defaults. Figure 3-8 Reset to Factory Defaults Upgrade Firmware Upgrades the switch system firmware using a file provided by Transition Networks. Select “Upgrade Firmware” from the Tools drop-down list then click on the “Browse” button to select the firmware file. -
Page 27: Figure 3-10 Upload/Download Configuration
Web Configuration Upload/Download Configuration Web – Click SYSTEM, Tools, Upload/Download Configuration. To upload or download the configuration file, select “Upload/Download Configuration” from the Tools drop-down list, then click “Upload” or “Download,” and then click on the “Browse” button to select the file. Figure 3-10 Upload/Download Configuration Restart Switch Web –... -
Page 28: Port Configuration
Configuring the Switch Port Configuration You can use the Port Configuration page to manually set the speed, duplex mode, and flow control. Field Attributes • – Allows you to manually set the port speed and duplex mode. Speed/Duplex • Flow Control – Allows flow control to be enabled or disabled. When the box is checked, flow control is enabled. -
Page 29: Port Mirroring
Web Configuration Field Attributes • Type – List the type of traffic which can be rate limited, including ICMP, learn frames, broadcast, multicast and flooded unicast frames. • Enable Storm Control – Click the check box to enable storm control for the specific frame type. -
Page 30: Cable Diagnostic
Configuring the Switch Web – Click PORTS, Port Mirroring. Figure 3-14 Port Mirroring Cable Diagnostic You can perform cable diagnostics for all ports or selected ports to diagnose any cable faults (short, open etc..) and feedback a distance to the fault. Field Attributes •... -
Page 31: Trunk Membership
Web Configuration Web – Click PORTS, Cable diagnostics. Figure 3-15 Cable Diagnostics Trunk Membership This page allows you to create a maximum of four trunks of up to eight ports per trunk. The Membership Table has one row for each port and six columns. Each row contains five radio buttons which are used to indicate which trunk (if any) the port belongs to. -
Page 32: Trunk Configuration
Configuring the Switch Web – Click TRUNKS, Membership. To assign a port to a trunk, click the required trunk number, then click APPLY. Figure 3-16 Trunk Membership Trunk Configuration Field Attributes • Trunk – Indicates trunk identification. • – Allows you to manually set the port speed and duplex mode for Speed/Duplex all ports in the trunk. -
Page 33: Lacp Setup
Web Configuration LACP Setup The switch supports both static trunking and dynamic Link Aggregation Control Protocol (LACP). LACP configured ports can automatically negotiate a trunked link with LACP-configured ports on another device. You can configure any number of ports on the switch as LACP, as long as they are not already configured as part of a static trunk. -
Page 34: Lacp Status
Configuring the Switch LACP Status This page displays the LACP status of the switch. Aggregation Information Shows aggregation information for each LACP group. Field Attributes • Aggregation Group - The ID number of the LACP group. • Partner MAC Address - The MAC address of link partner. •... -
Page 35: Vlan Settings
Web Configuration VLAN Settings This page allows you to create and delete VLANs (Virtual LANs) and to change the VLAN membership and behaviour of individual ports. VLANs are powerful, but can be difficult to set up properly. Each row of the table corresponds to one port or trunk; trunked ports cannot be configured individually. -
Page 36: Figure 3-20 Vlan Settings
Configuring the Switch Web – Click VLANS, VLAN Membership. Create a new VLAN by giving it an ID (Range: 1~4094) and then click Add. Modify or delete a VLAN by selecting its radio button and clicking Modify or Delete. Figure 3-20 VLAN Settings VLAN Configuration After creating a new VLAN, configure port and trunk members for the selected VLAN index. -
Page 37: Figure 3-21 Vlan Group Settings
Web Configuration Web – After creating a new VLAN, the following screen displays. Assign the ports and trunks associated with the VLAN, and click Apply. Figure 3-21 VLAN Group Settings VLAN Port Configuration There are three different parameters that can be configured for each port on the switch;... -
Page 38: 802.1X
Configuring the Switch is a member of the VLAN identified by the VLAN tag in the packet. (Default: All) • PVID – The port VLAN ID (PVID) assigned to untagged frames received on the interface. From the drop-down menu, choose the VLAN ID that will be assigned to untagged frames received on the port. - Page 39 Web Configuration 802.1 X Setting The IEEE 802.1X standard defines a port-based access control procedure that prevents unauthorized access to a network by requiring users to first submit credentials for authentication. Field Attributes System Setting • Mode - Indicates if 802.1X protocol is globally enabled or disabled on the switch. •...
-
Page 40: Figure 3-23 802.1X Configuration
Configuring the Switch Web – Click 802.1X, Settings. Figure 3-23 802.1X Configuration 802.1X Statistics Field Attributes • Port Statistics - Statistics can be viewed on a per-port basis. Select the port that you want to view here. • Authenticator counters - General statistics for authenticator. •... -
Page 41: Lldp
Web Configuration Web – Click 802.1X, Statistics. Figure 3-24 802.1X Statistics LLDP This page allows you to configure the Link Layer Discovery Protocol (LLDP) configuration. LLDP allows devices on the network to share information about themselves for the reasons of simplified troubleshooting, enhanced network management, and maintaining an accurate network topology. -
Page 42: Lldp Neighbor Table
Configuring the Switch Web – Click LLDP, Settings. Figure 3-25 LLDP Configuration LLDP Neighbor Table This page displays the LLDP Neighbor Table. This table provides information on neighboring devices. The table contains the following seven columns: Field Attributes • Local Port - The local port of the neighboring device. •... -
Page 43: Snmp
Web Configuration Web – Click LLDP, Neighbor. Figure 3-26 LLDP Neighbor SNMP Simple Network Management Protocol (SNMP) is a communication protocol designed specifically for managing devices on a network. Equipment commonly managed with SNMP includes switches, routers and host computers. SNMP is typically used to configure these devices for proper operation in a network environment, as well as to monitor them to evaluate performance or detect potential problems. -
Page 44: Poe
Configuring the Switch Web – Click SNMP, Configuration. Figure 3-27 SNMP Configuration The switch can provide DC power to a wide range of connected devices, eliminating the need for an additional power source and cutting down on the amount of cables attached to each device. -
Page 45: Switch Power Status
Web Configuration Switch Power Status Displays the Power over Ethernet parameters for the switch. Field Attributes • Port 1 Power Mode – Port 1 may be configured to supply as much as 25 watts of power when set to High mode. In normal mode it can supply a maximum of 15.4 watts. - Page 46 Configuring the Switch 3-32...
-
Page 47: Appendix A: Software Specifications
Appendix A: Software Specifications Software Features Authentication RADIUS, Port (802.1X), Port Security DHCP Client Port Configuration 100BASE-TX: 10/100 Mbps, half/full duplex 1000BASE-T: 10/100 Mbps at half/full duplex, 1000 Mbps at full duplex Flow Control Full Duplex: IEEE 802.3-2005 Half Duplex: Back pressure Broadcast Storm Control Traffic throttled above a critical threshold Port Mirroring... -
Page 48: Management Features
Software Specifications Management Features In-Band Management Web-based HTTP, SNMP manager Software Loading HTTP in-band SNMP Management access via MIB database Trap management Standards IEEE 802.1D Bridging IEEE 802.1p Priority tags IEEE 802.1Q VLAN IEEE 802.1X Port Authentication IEEE 802.3-2005 Ethernet, Fast Ethernet, Gigabit Ethernet Full-duplex flow control Link Aggregation Control Protocol IEEE 802.3ac VLAN tagging... -
Page 49: Appendix B: Troubleshooting
Appendix B: Troubleshooting Forgot or Lost Password If you have forgotten the administration password you can return the switch to its factory default state by following these steps: Remove the power cord from the back of the switch. Remove all cables from the front-panel ports. Connect port 1 to port 2 on the front panel, using a standard network cable. - Page 50 Troubleshooting In the Internet Protocol (TCP/IP) Properties dialog box, click to select Use the following IP address. Then type your intended IP address, Subnet mask, and Default gateway in the provided text boxes. Click OK to save the changes. Note: For users of systems other than Windows 2000 or Windows XP, refer to your system documentation for information on changing the PC’s IP address.
- Page 52 MIL-SM8TAF1GPA E052008-AP-R01 149100036400A...
Need help?
Do you have a question about the MIL-SM8TAF1GPA and is the answer not in the manual?
Questions and answers