General Specifications - New Holland WORKMASTER 35 Operator's Manual

General specifications

- Workmaster 35
Hydrostatic/
ENGINE
Type Diesel
Model L3BL
Engine Gross 24.6 kW (33 Hp) 28.3 kW (38 Hp)
Horsepower
Cylinders 3
Bore 88 mm (3367 in) 90 mm (3.54 in)
Stroke 105 mm (4.13 in) 105 mm (4.13 in)
Displacement 1..915 l
(116.86 in³)
Compression 22.0:1
Ratio
Firing Order 1-3-2
Low Idle Speed 1120±20 RPM
Maximum
Speed:
High Idle 2800 ±30 RPM
Rated 2600 RPM
Valve Clearance
(Cold)
Intake 0.25 mm
(0.010 in)
Exhaust 0.25 mm
(0.010 in)
CAPACITIES
Fuel Tank
28.0 l (7.4 US
gal)
Cooling System 5.0 l (1.3 US gal) 5.0 l (1.3 US gal)
Engine
Crankcase:
With Filter 6.5 l (6.9 US qt)
Rear Axle &
Transmission
(Includes
Hydraulics)
Gear 30.0 l (7.9 US
gal)
HST 30.0 l (7.9 US
gal)
Front Axle 5.5 l (5.8 US qt)
COOLING SYSTEM
Type Pressurized
Liquid with
Recirculating
Bypass
Water Pump:
Type Centrifugal
Drive V-Belt
9 - SPECIFICATIONS
Model Model
- Workmaster 40
Hydrostatic/
Gear Gear
Diesel
L3AL
3
2.003 l
(122.23 in³)
22.0:1
1-3-2
1120±20 RPM
2800 ±30 RPM
2600 RPM
0.25 mm
(0.010 in)
0.25 mm
(0.010 in)
28.0 l (7.4 US
gal)
6.5 l (6.9 US qt)
30.0 l (7.9 US
gal)
30.0 l (7.9 US
gal)
5.5 l (5.8 US qt)
Pressurized
Liquid with
Recirculating
Bypass
Centrifugal
V-Belt
- Workmaster 35
Belt Deflection 10 - 12 mm
(0.4 - 0.47 in)
when 10 kg
(22 lb) pressure
is applied midway
between belt
pulleys
Fan Diameter 380 mm (15.0 in) 380 mm (15.0 in)
Thermostat:
Start to Open 76.5 °C (170 °F)
Fully Open 90 °C (194 °F)
Radiator Cap 90 kPa (13 psi)
ELECTRICAL SYSTEM
Alternator 12 V, Heavy Duty,
50 A
Battery
12 V, w/ negative
ground, 660 cca
BCI Group 34
Starting Motor Solenoid
Pre-Engaged
Reduction
FUEL SYSTEM
Fuel Type Diesel
Type of Fuel No. 2-Diesel,
to Use if Above Cetane Rating:
4 °C (40 °F) Minimum 40
No. 1-Diesel,
Type of Fuel
to Use if Below Cetane Rating:
4 °C (40 °F) Minimum 40
Injection Pump:
Type Rotary
Timing 3 ° ATDC
CLUTCH
Type 240 mm (9.4 in)
- Transmission
12x12 Trans
Pedal Free- 20 - 30 mm (0.79
Travel - 1.2 in)
BRAKES
Type Wet Disc
2 Disc per Side 223 mm (8.78 in)
x 174 mm
(6.85 in)
9-3
Model Model
- Workmaster 40
Hydrostatic/ Hydrostatic/
Gear Gear
10 - 12 mm
(0.4 - 0.47 in)
when 10 kg
(22 lb) pressure
is applied midway
between belt
pulleys
76.5 °C (170 °F)
90 °C (194 °F)
90 kPa (13 psi)
12 V, Heavy Duty,
50 A
12 V, w/ negative
ground, 660 cca
BCI Group 34
Solenoid
Pre-Engaged
Reduction
Diesel
No. 2-Diesel,
Cetane Rating:
Minimum 40
No. 1-Diesel,
Cetane Rating:
Minimum 40
Rotary
3 ° ATDC
240 mm (9.4 in)
- Transmission
12x12 Trans
20 - 30 mm (0.79
- 1.2 in)
Wet Disc
223 mm (8.78 in)
x 174 mm
(6.85 in)