HBK FS22DI Quick Start Manual
  1. Manuals
  2. Brands
  3. HBK Manuals
  4. Measuring Instruments
  5. FS22DI
  6. Quick start manual

HBK FS22DI Quick Start Manual

Industrial braggmeter di
Hide thumbs Also See for FS22DI:
Table of Contents

Advertisement

Quick Links

Download this manual
ENGLISH
Quick Start Guide
FS22DI
Industrial BraggMETER DI

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the FS22DI and is the answer not in the manual?

Questions and answers

Related Manuals for HBK FS22DI

Summary of Contents for HBK FS22DI

  • Page 1 ENGLISH Quick Start Guide FS22DI Industrial BraggMETER DI...
  • Page 2 Hottinger Brüel & Kjaer GmbH Im Tiefen See 45 D-64293 Darmstadt Tel. +49 6151 803-0 Fax +49 6151 803-9100 info@hbkworld.com www.hbkworld.com HBK FiberSensing, S.A. Rua Vasconcelos Costa, 277 4470-640 Maia Portugal Tel. +351 229 613 010 Fax +351 229 613 020 info.fs@hbkworld.com www.hbm.com/fs...

  • Page 3: Table Of Contents

    ..........FS22DI...

  • Page 4: Introduction

    INTRODUCTION This document is a quick start guide for operating the FS22 - Industrial BraggMETER DI interrogator from HBK FiberSensing. For more details please refer to the full user manual provided with the equipment. This document is also available for download on our website.
  • Page 5 - Mounting blocks with M6 screws - Connector protection caps - Connector protection caps - Quick start guide - Mounting hole protection caps - Digital support material - Quick start guide - Calibration certificate - Digital support material - Calibration certificate FS22DI INTRODUCTION...

  • Page 6: Interrogator Setup

    The connectors and buttons in Fig. 2.1 are: Optical Output Connectors ON/OFF Button Power Connector Ethernet Connector POWER and STATUS LEDs 2.1.2 Rack Mountable Format The FS22 - Industrial BraggMETER DI on its Rack-Mountable format has the following buttons and connectors: FS22DI INTERROGATOR SETUP...

  • Page 7: Turn On

    Then, switch the safety power button ON. Notice Powering above the specified limits will damage the equipment. For the Rack-mountable version there is a fuse protection that can be replaced. Please refer to the full user manual for details. FS22DI INTERROGATOR SETUP...

  • Page 8: Ethernet

    Please note that the durations stated in Fig. 2.4 are merely indicative and may vary depending, for example, on the sampling rate of the interrogator. Important In case the interrogator does not start correctly, contact HBK FiberSensing for technical support. 2.2.2...

  • Page 9: Optical

    Set the TCP properties of the computer as follows: IP address: 10.0.0.xxx (where xxx should not be 150: the default IP of the FS22DI is 10.0.0.150) Subnet mask: 255.0.0.0 Test the connection: Launch a command line (e.g. Start → Run → type “cmd”, in Windows environment) Type and execute the following command: “ping 10.0.0.150”...

  • Page 10: Remote Communications

    The FS22 - Industrial BraggMETER DI interrogator can be fully controlled using standard SCPI syntax commands. The interrogator has 5 different operational states that answer to the listed commands below. Fig. 3.1 For full information on the commands refer to the interrogator user manual. FS22DI REMOTE COMMUNICATIONS...

  • Page 11: Braggmonitor Di Software

    BraggMONITOR DI Software. For a full description of the software please refer to the full user manual. 4.2.1 Connect to the Interrogator To establish a connection to the interrogator press the “connect” button (number Fig. 4.1) on the general bar available at the bottom of the software window. Fig. 4.1 FS22DI BRAGGMONITOR DI SOFTWARE...

  • Page 12: Configure Measurements

    View tab. Press the corresponding tab, on top of the graphical user interface, to select it (number in Fig. 4.2). Fig. 4.2 The settings to adjust on the FS22DI Interrogator are the gain (number in Fig. 4.2) and the threshold (number in Fig. 4.2). The “get” buttons query the interrogator for the stored values and the “set”...

  • Page 13: Set The Configuration

    Set the values to the most appropriate ones taking into consideration the existing signals. 4.2.3 Set the Configuration The configuration of the sensors can be adjusted under the Configuration tab (number in Fig. 4.3). Fig. 4.3 FS22DI BRAGGMONITOR DI SOFTWARE...

  • Page 14: Start Acquisition

    “edit” button (number in Fig. 4.3). 4.2.4 Start Acquisition Still in the Configuration tab configure: Fig. 4.4 Measurement acquisition rate (number in Fig. 4.4): Possible values: 50 S/s; 100 S/s; 200 S/s; 500 S/s; 1000 S/s FS22DI BRAGGMONITOR DI SOFTWARE...
  • Page 15 To start saving data to a data file press the “save” button (number in Fig. 4.5). Important For further information please refer to the user manual provided with the equipment. This document is also available on our website. FS22DI BRAGGMONITOR DI SOFTWARE...
  • Page 16 HBK - Hottinger Brüel & Kjaer www.hbkworld.com info@hbkworld.com...

Table of Contents