Soyal AR-101-H Installation Manual

SOYAL
ACCESS & INDUSTRIAL CONTROL
Content
1 Product 2 Terminal Cables
CN1
AR-101-H/U
Feature
AR-101-H
Selectable working frequencies: 13.56MHz
Including the input of door contact, offering the alarm system of both
door opening too long and being forced to open
Built-in Multi-Output: Door Lock/ Alarm/ Security trigger signal
Have the "MASTER CARD" functions, convenient operation
Mini Flush-Mounted design gives neat installation
Elegant design with colorful Edge Indicator
Connector Table
CN1
AR-101-H
8PIN Cable
Function Wire
1
2
Lock Relay
3
Door Contact 4
Exit Switch 5
Alarm 6
7
Power
8
AR-101-H/U CN2
2PIN Cable
Function Wire
1
RS-485
2
AR-101-H/U J3
4PIN Cable
Function Wire
1
2
Wiegand Reader/
Ex. Keyboard
3
4
AR-101-U Dip-switch &
Wire
Dip-switch-SW1 ---
Dip-switch-SW2 ---
Description ---
1
2
3
4
CN1 Cable
5
6
7
8
®
3 Black ABS 4
CN2
Color Description
Blue White (N.O.) DC24V1Amp
Purple White (N.C.) DC24V1Amp
White (COM) DC24V1Amp
Orange Negative Trigger Input
Purple Negative Trigger Input
Transistor Output Max. 12V/100mA
Gray
(Open Collector Active Low)
Thick Red DC 9~24V
Thick Black DC 0V
Color Description
Thick Green RS-485(B-)
Thick Blue RS-485(A+)
Color Description
Thick Red DC 9~24V
Thick Black DC 0V
Thick Blue Wiegand DAT:1 Input
Thick Green Wiegand DAT:0 Input
CN1
8PIN Cable
Color
RS-485 Mode/
Polling Mode
(Connected to AR-716-E16)
--- ON
--- ON
Auto-open Time Zone
Auto Open with
---
swiping 1st valid
card at Auto-open
Time Zone
Blue White ---
Green White ---
White Door Lock Output
Orange Door Sensor
Purple Exit Button
Gray Buzzer
Thick Red
Power
Thick Black
AR-101-H/U
Optional (panel) 5 Optional(only 101-H)
Wiegand Keyboard :
AR-WG-KEYBOARD
DMET-101PJ
AR-101-U (RS485/WG)
Selectable working frequencies: 125KHz/13.56MHz
From the DIP switch to select to be RS485 or WG output reader
Flexible to integrate with SOYAL or other access control system
Interface of the Proximity Reader have WG26/34 (By order)
Elegant design with colorful Edge Indicator
Flush-Mounted Design gives neat installation
※ Dip-switch is only available for AR-101-U
＊Dip-switch must adjust at 2nd layer of mainboard.
Highly suggest to fixed WG34/26 before order
How to adjust dip-switch:
A
Step 1.
Open lightly the upper board
cover with screwdriver
Function
WG Mode
OFF ON
ON OFF
WG34
(default)
Auto-open door at
auto open zone
WG Output
---
LED R
LED G
- 1 -
Extenal Relay :
or
AR-821-RB AR-721-RB
ON
1 2
Front
B
B
ON
1
Step 2.
Adjust the DIP switch according to
the function and put upper cover
back on the upper board
OFF
OFF
Description
WG26
WG DATA 1 Output
WG DATA 0 Output
Transistor Output Max. 24V/1.5A
(Open Collector Active Low)
Negative Trigger Input
Negative Trigger Input
Transistor Output Max. 12V/100mA
(Open Collector Active Low)
DC 12V
DC 0V
V221024
Master Card :
(Keyless editing)
1
CN2
2
1
2
3
4
4 5
CN1
3 6
J3
2 7
1 8
Back
A
2