Dodge R1500 1999 Service Manual page 315

Passenger's Door Open Or Close
Driver's Door Lock Switch
Passenger's Door Lock Switch
Driver's Key Cylinder
Passenger's Key Cylinder
Driver's Door Unlock Switch
Passenger's Door Unlock Switch
¡ ¢ ¡ ¢ ¡ ¢ ¡ ¢ ¡ ¢ ¡ ¢ ¡ ¢ ¡ ¢ ¡ ¢ ¡ ¢ ¡ ¢ ¡ ¢ ¡ ¢ ¡ ¢ ¡ ¢ ¡ ¢ ¡ ¢ ¡ ¢ ¡ ¢ ¡ ¢ ¡ ¢ ¡ ¢ ¡ ¢ ¡ ¢ ¡ ¢ ¡ ¢ ¡ ¢ ¡ ¢ ¡ ¢ ¡ ¢ ¡ ¢ ¡ ¢ ¡ ¢ ¡ ¢ ¡ ¢ ¡ ¢ ¡ ¢ ¡ ¢ ¡ ¢ ¡ ¢ ¡ ¢ ¡ ¢ ¡ ¢ ¡ ¢ ¡ ¢ ¡ ¢ ¡ ¢ ¡ ¢ ¡ ¢ ¡ ¢ ¡ ¢ ¡ ¢ ¡ ¢ ¡ ¢ ¡ ¢ ¡ ¢ ¡ ¢ ¡ ¢ ¡ ¢ ¡ ¢ ¡ ¢ ¡ ¢ ¡ ¢ ¡ ¢ ¡ ¢ ¡ ¢ ¡ ¢ ¡ ¢ ¡ ¢ ¡
15) Ensure driver's door is closed. Using scan tool, read
VTSS inputs/outputs door ajar status. If scan tool displays DR DOOR
AJAR SWITCH: CLOSED, go to SHORTED LEFT DOOR AJAR CIRCUIT under DOOR
AJAR SYSTEM. If scan tool does not display DR DOOR AJAR SWITCH:
CLOSED, go to OPEN LEFT DOOR AJAR CIRCUIT under DOOR AJAR SYSTEM.
16) Ensure passenger's door is closed. Using scan tool, read
VTSS inputs/outputs door ajar status. If scan tool displays DR DOOR
AJAR SWITCH: CLOSED, go to SHORTED RIGHT DOOR AJAR CIRCUIT under DOOR
AJAR SYSTEM. If scan tool does not display DR DOOR AJAR SWITCH:
CLOSED, go to OPEN RIGHT DOOR AJAR CIRCUIT under DOOR AJAR SYSTEM.
17) Using scan tool, monitor door disarm switch state.
Disconnect left door disarm switch. Connect jumper wire between left
door disarm switch connector terminals. If scan tool displays door
disarm switch state CLOSED, replace left door disarm switch. If scan
tool does not display door disarm switch state CLOSED, go to next
step.
18) Disconnect jumper wire. Connect jumper wire between
ground and left door disarm switch connector Light Green/Orange wire.
If scan tool displays door disarm switch state CLOSED, go to next
step. If scan tool does not display door disarm switch state CLOSED,
repair open left door disarm switch ground circuit (Black/Light Green
wire).
19) Access Central Timer Module (CTM). CTM is located behind
right kick panel. Remove connector cover. Do not disconnect connector.
Connect a jumper between ground and backprobe CTM 18-pin connector C2
terminal No. 10 (Light Green/Orange wire). If scan tool displays door
disarm switch state CLOSED, repair open left door disarm switch sense
circuit (Light Green/Orange wire). If scan tool does not display door
disarm switch state CLOSED, replace CTM.
20) Using scan tool, monitor door disarm switch state.
Disconnect right door disarm switch. Connect jumper wire between right
door disarm switch connector terminals. If scan tool displays door
disarm switch state CLOSED, replace right door disarm switch. If scan
tool does not display door disarm switch state CLOSED, go to next
step.
21) Disconnect jumper wire. Connect jumper wire between
ground and right door disarm switch connector Light Green/Orange wire.
If scan tool displays door disarm switch state CLOSED, go to next
step. If scan tool does not display door disarm switch state CLOSED,
repair open right door disarm switch ground circuit (Black/Light Green
wire).
22) Access Central Timer Module (CTM). CTM is located behind
right kick panel. Remove connector cover. Do not disconnect connector.
Connect a jumper between ground and backprobe CTM 18-pin connector C2
terminal No. 10 (Light Green/Orange wire). If scan tool displays door
disarm switch state CLOSED, repair open right door disarm switch sense
circuit (Light Green/Orange wire). If scan tool does not display door
............................
.................
..............
.....................................
..................................
...............
............
Step 16)
ONE OR ALL DOORS FAILING
TO LOCK FROM ONE SWITCH
ONE OR ALL DOORS FAILING
TO LOCK FROM ONE SWITCH
Step 17)
Step 20)
ONE OR ALL DOORS FAILING
TO UNLOCK FROM ONE SWITCH
ONE OR ALL DOORS FAILING
TO UNLOCK FROM ONE SWITCH