Advertisement
Quick Links
INSTRUCTION MANUAL
E2xBL2 LED Beacon
For use in Hazardous Locations
1) Product Table
E2xBL2DC024
E2xBL2AC115
E2xBL2AC230
The current levels shown above are for the worst-case input voltage and flash setting resulting in max. current.
Table 1: Electrical Ratings.
Ensure the system power supply is capable of providing the maximum current required for all units. Review associated cable
size, length and quantity of units on each circuit.
2) Warnings
DO NOT OPEN WHEN AN EXPLOSIVE
ATMOSPHERE IS PRESENT
DO NOT OPEN WHEN ENERGISED
POTENTIAL ELECTROSTATIC CHARGING
HAZARD - CLEAN ONLY WITH A DAMP
CLOTH
HIGH VOLTAGE SHOCK HAZARD. WAIT 5
MINUTES AFTER REMOVING POWER
BEFORE OPENING THE ENCLOSURE
Avertissement:
NE PAS OUVRIR UN PRESENCE
D'ATMOSPHERE EXPLOSIVE
NE PAS OUVRIR ENERGIE
DANGER POTENTIEL CHARGE
ÉLECTROSTATIQUE - NETTOYER
UNIQUEMENT AVEC UN CHIFFON HUMIDE
HAUT TENSION, RISK DE CHOC.
ATTENDEZ 5 MINUTES APRES AVOIR
DEBRANCHE L'ALIMENTATION AVANT
D'OUVRIR LA BOITIER
3) Rating & Marking Information
3.1. ATEX / IECEx / UKEx certification
The E2xBL2 LED beacon complies with the following
standards:
European Safety Systems Ltd. Impress House, Mansell Road, Acton, London W3 7QH
Document No. D209-00-401-IS
Model
Issue 1
E2XBL2
Nom. Voltage
24Vdc
115-120Vac
Nominal +/- 10%
50/60Hz
220-230Vac
Nominal +/- 10%
50/60Hz
EN IEC 60079-0:2018 / IEC60079-0:2017 (Ed 7):
Explosive Atmospheres - Equipment. General Requirements
EN IEC 60079-7:2015 +A1:2018 / IEC 60079-7:2018 (Ed. 5.1):
Explosive Atmospheres - Equipment Protection by Increased
Safety "e"
EN 60079-31:2014 / IEC 60079-31:2013 (Ed 2):
Explosive Atmospheres - Equipment Dust Ignition Protection by
Enclosure "t"
E2XBL2:
Certificate No.
ATEX Mark, Equipment
Group and Category:
CE Marking
UKCA Marking
20-08-22
Voltage Range
18-54Vdc
Standards
Ratings
Ex ec IIC Gc T4 Ta -20°C to +55°C
Ex tb IIIC Dc T85°C Ta -20°C to +55°C
DEMKO 06ATEX 0421554X
IECEx ULD 14.0012X
UL21UKEX2135X
www.e2s.com
Max Operating
Current*
346mA
102.4mA
49.4mA
II 3G
II 3D
Tel: +44 (0)208 743 8880
Sheet 1 of 5
Advertisement
Related Manuals for E2S E2xBL2
Summary of Contents for E2S E2xBL2
- Page 1 CE Marking 3) Rating & Marking Information 3.1. ATEX / IECEx / UKEx certification UKCA Marking The E2xBL2 LED beacon complies with the following standards: European Safety Systems Ltd. Impress House, Mansell Road, Acton, London W3 7QH www.e2s.com Tel: +44 (0)208 743 8880 Document No.
- Page 2 Temperature Classification EN60079-10-2 / IEC60079-10-2: Explosive atmospheres – Classification of areas. Explosive dust atmospheres When connected to an approved system the E2XBL2 LED beacon may be installed in: European Safety Systems Ltd. Impress House, Mansell Road, Acton, London W3 7QH www.e2s.com...
-
Page 3: Special Conditions Of Use
+80ºC. Therefore suitable heat resisting cables and cable glands must be used as per table below European Safety Systems Ltd. Impress House, Mansell Road, Acton, London W3 7QH www.e2s.com Tel: +44 (0)208 743 8880 Document No. D209-00-401-IS Issue 1... -
Page 4: Cable Connections
This is particularly important when using On E2xBL2 DC units, DC reverse line monitoring can be cables with large cross sectional areas such as 2.5mm². used if required. All DC beacons have a blocking diode fitted in their supply input lines. - Page 5 4mm Allen Key. Remove the wire guard and replace the old cover with the new cover. The E2xBL2 beacons can produce different flash patterns as shown in Table 1. The flash patterns are selected by M5 screw operation of the flash setting DIP switch on the PCB, Fig 6.
- Page 6 OPTIONAL LINE MONITORING RESISTOR, CUSTOMER SUPPLIED, REQUIRED MINIMUM VALUES: 24VDC : 1KΩ MIN, 2W MIN OR 3K9Ω MIN, 0.5W MIN 48VDC : 3.9KΩ MIN, 2W MIN OR 15KΩ MIN, 0.5W MIN DC LED E2XBL2 UNITS AC LED E2XBL2 UNITS Line Monitoring Power: Live & Neutral Stage 1 Flash Pattern: Apply power to +ve &...
-
Page 7: Eu Declaration Of Conformity
Other Standards and Regulations EN 60529:1992+A2:2013 - Degrees of protection provided by enclosures (IP code) – enclosure rated IP66/IP67 E2S Telephone: +44 (0)20 8743 8880 Fax: +44 (0)20 8740 4200 Email: sales@e2s.com www.e2s.com DC-062_Issue_I (E2x).docx - Page 1 of 2 - QAF_252_Issue_5... - Page 8 This Declaration is issued under the sole responsibility of the manufacturer. Martin Streetz Document No.: DC-062_Issue_I Quality Assurance Manager Date and Place of Issue: London, 22/08/2022 E2S Telephone: +44 (0)20 8743 8880 Fax: +44 (0)20 8740 4200 Email: sales@e2s.com www.e2s.com DC-062_Issue_I (E2x).docx - Page 2 of 2 - QAF_252_Issue_5...
- Page 9 Other Standards and Regulations EN 60529:1992+A2:2013 ‐ Degrees of protection provided by enclosures (IP code) – enclosure rated IP66/IP67 E2S Telephone: +44 (0)20 8743 8880 Fax: +44 (0)20 8740 4200 Email: sales@e2s.com www.e2s.com DC-103_Issue_A - Page 1 of 2 - QAF_252_Issue_5...
- Page 10 This Declaration is issued under the sole responsibility of the manufacturer. Martin Streetz Document No.: DC‐103_Issue_A Quality Assurance Manager Date and Place of Issue: London, 22/08/2022 E2S Telephone: +44 (0)20 8743 8880 Fax: +44 (0)20 8740 4200 Email: sales@e2s.com www.e2s.com DC-103_Issue_A - Page 2 of 2 - QAF_252_Issue_5...