Summary of Contents for Crane PROSSER PUPP512 Series
Page 1
Read all instructions in this manual before operating pump. As a result of Crane Pumps & Systems, Inc., constant product improvement program, product changes may occur. As such Crane Pumps & Systems, Inc., reserves the right to change product without prior written notification.
START-UP REPORT WARRANTY REGISTRATION Other brand and product names are trademarks or registered trademarks of their respective holders. Barnes® is a registered trademark of Crane Pumps & Systems Inc. 1995 1997, 1998, 2002, 2003 Alteration Rights Reserved. Printed in U.S.A.
CAUTION ! Pumps build up heat and pressure during operation-allow time for pumps to cool Crane Pumps & Systems, Inc. is not responsible for losses, before handling or servicing. injury, or death resulting from a failure to observe these...
B-4) Service Centers: For the location of the nearest Barnes Center, check your Barnes Engineered catalog, your Barnes representative or Barnes Service Department in Piqua, Ohio, telephone (937) 778-8947 or Crane Pumps & Systems Canada, in Brampton, Ontario, (905) 457-6223.
MODEL VOLT PH RPM NEMA FULL LOCKED WINDING (Nom) START LOAD ROTOR RESISTANCE CODE AMPS AMPS PUPP512 3450 25.2 1.15* Pump rated for operation at ± 10% Voltage at Motor. Winding resistance ± 10% voltage at motor. * Measured at the cord end. C-3.1) Power Cable: D-3) Start-Up: The cord assembly mounted to the pump must not be modified...
TROUBLESHOOTING CAUTION ! Always disconnect the pump from the electrical power source before handling. If the system fails to operate properly, carefully read instructions and perform maintenance recommendations. If operating problems persist, the following chart may be of assistance in identifying and correcting them: MATCH "CAUSE"...
SECTION: G REPLACEMENT PARTS G-1 ORDERING REPLACEMENT PARTS: When ordering replacement parts, ALWAYS furnish the following information: 1. Pump serial number and date code. (G-4) 2. Pump model number. (G-3) 3. Pump part number.(G-2) 4. Part description. 5. Item part number. 6.
PARTS LIST ITEM DESCRIPTION MOTOR KIT: PART No. 096993 HANDLE KIT PART No. 096988 Motor Handle Motor Frame Screw Spacer Centrifugal Force Switch Cover DISCHARGE KIT: PART No. 096987 Bearing Washer O-Ring Terminal Protector Condenser Delivery Flange Centrifugal Force Switch Band OTHER: Wave Washer...
Complete the Warranty Registration Form and returned to Crane Pumps & Systems, Inc. Warranty Service Group IMPORTANT! If you have a claim under the provision of the warranty, contact your local Crane Pumps & Systems, Inc. Distributor. RETURNED GOODS RETURN OF MERCHANDISE REQUIRES A "RETURNED GOODS AUTHORIZATION".
Page 12
No rights extended under this warranty shall be assigned to any other person, whether by operation of law or otherwise, without our prior written approval. PUMPS & SYSTEMS A Crane Co. Company 420 Third Street/P.O. Box 603 83 West Drive, Brampton...
This report is designed to insure the customer that customer service and a quality product are the number one priority with Crane Pumps & Systems, Inc. (CP&S). Please answer the following questions completely and as accurately as possible. Mail this form to: In U.S.A.
Page 14
CP&S Control Panel Part No. and Brand Number of pumps operated by control panel NOTE: At no time should holes be made in top of control panel, unless proper sealing devices are utilized. Control Panel Manufactured by Others: Company Name: Model No.
Complete the Warranty Registration Form and returned to Crane Pumps & Systems, Inc. Warranty Service Group IMPORTANT! If you have a claim under the provision of the warranty, contact your local Crane Pumps & Systems, Inc. Distributor. FOLD HERE ** IMPORTANT ! ** WARRANTY REGISTRATION CUSTOMER’S NAME...
Page 16
FOLD HERE AND TAPE, DO NOT STAPLE PLACE STAMP HERE CRANE PUMPS & SYSTEMS, INC. WARRANTY SERVICE GROUP 420 THIRD STREET P.O. BOX 603 PIQUA, OHIO 45356-0603 - U.S.A.
Need help?
Do you have a question about the PROSSER PUPP512 Series and is the answer not in the manual?
Questions and answers