Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Matco Tools MPPC70DV
Summary of Contents for Matco Tools MPPC70DV
- Page 1 MPPC70DV INVERTER DC PLASMA CUTTER OWNER’S MANUAL 11/2019 WARNING: Read carefully and understand all ASSEMBLY AND OPERATION INSTRUCTIONS before operating. Failure to follow the safety rules and other basic safety precautions may result in serious personal injury. 2004058-12 Page 1 of 16...
-
Page 2: Limited Warranty
Limited to the warranty periods below, MATCO TOOLS will repair or replace the item under warranty that fails due to defects in material and workmanship. MATCO TOOLS must be notified within 30 days of the failure, to provide instructions on how to proceed with the repair of your welder and warranty claim processing. -
Page 3: General Safety Rules
-Always have your plasma cutter maintained by GENERAL SAFETY RULES a qualified technician in accordance with local, state and national codes. WARNING: Read and understand all -Always be aware of your work environment. Be instructions. Failure to follow all instructions sure to keep other people, especially children, listed below may result in serious injury. - Page 4 -Wear proper gloves and protective clothing to -Do not breathe in fumes emitted by the plasma prevent your skin from being exposed to hot cutting process. Make sure your breathing air is metals, UV and IR rays. clean and safe. -Do not overuse or overheat your plasma -Work only in a well-ventilated area or use a cutter.
-
Page 5: Maintenance
gaseous or liquid combustibles in them. Plasma -Consult your doctor before using any plasma cutting creates sparks and heat that can ignite cutting device flammable and explosive materials. -Keep people with pacemakers away from your -Do not operate any plasma cutter in areas plasma cutting area while cutting. -
Page 6: Technical Specifications
Weight 22.93 lbs. DESCRIPTION kerf that results in a smaller heat affected zone The Matco Tools MPPC70 is a Dual Voltage, DC for reduced warping. The MPPC70 is Inverter Plasma Cutter. It uses new state of the lightweight (22.93 lbs.), compact, inverter design art technology. - Page 7 Clean Cut Clean Cut Material 120V 230V Mild Steel 1/4" 11/16" Stainless Steel 1/4" 9/16" Galvanized 1/4" 9/16" Aluminum 3/16" 9/16" Copper 3/16" 7/16" Brass 3/16" 7/16" AIR PRESSURE DISPLAY operating on 230V power, the pressure should The built-in air display is used for reading the be adjusted between 50-80psi.
-
Page 8: Current Adjustment
trigger is pulled, indicating cutting current is Plug this unit into a 230V, 50A circuit breaker activated. power supply when operating on 230V. If PROTECTION INDICATOR LIGHT running on 120V power using the supplied When the unit is in thermal overload, is over 120V power cord adapter, plug this unit into a voltage or lacking voltage, the indicator will be 120V, 20A circuit breaker power supply. -
Page 9: Operation
3. EXTENSION CORD - We do not cord over 25 ft. in length. recommend an extension cord because 4. INSTALLATION OF THE CUTTING of the voltage drop they produce. This TORCH CONSUMABLES drop-in voltage can affect the a. Your torch should be fully performance of the plasma assembled and ready to cutter/welder. -
Page 10: Important Safety
power cord to a properly grounded 230 VAC (220V - 240V), 60 HZ, single phase, 50A power source. If operating on 120V, attach the 120V Adapter cord to the unit power cord and then connect the assembly to a properly grounded 120 VAC (110V-130V), 60 Hz, single phase, 20A power source. -
Page 11: Safety Requirements
cause the nozzle to stick, reducing If necessary, use exhaust/ventilation the smoothness of the cutting fans to keep fumes or emissions away action creating an undesirable from the breathing zone. result. Do not touch the work piece while Keep the torch’s nozzle vertical cutting. -
Page 12: Troubleshooting
TROUBLESHOOTING SYMPTOM POSSIBLE CAUSE CORRECTIVE ACTION Unit is not plugged in Plug unit in Input power circuit breaker not on Reset input power circuit breaker Unit does not power up Main power switch is defective Replace main power switch Control circuit board is defective Replace control circuit board Check air supply Adjust gas pressure adjuster so the air... -
Page 13: Main Circuit Diagram
MAIN CIRCUIT DIAGRAM 2004058-12 Page 13 of 16... -
Page 14: Parts Diagram
PARTS DIAGRAM 2004058-12 Page 14 of 16... -
Page 15: Parts List
GAS VALVE WITH WATER SEPERATOR ASSEMBLED ITEM WATER SEPERATOR DRAIN HOSE 105400110 AIR PRESSURE REGULATOR * ITEMS ARE NOT PICTURED Replacement parts can be ordered through your Matco Tools Distributor For technical questions, call 855-920-2399. 2004058-12 Page 15 of 16... - Page 16 Distributed by Matco Tool 4403 Allen Road Stow OH 44224 w w w . m a t c o t o o l s . c o m Made in China to Matco specifications 2004058-12 Page 16 of 16...