Advertisement
APPROVAL
This application head is approved for use on the following powerbases:
OMNI 12C-PB
OMNI 18C-PB
OMNI 300-PB
TECHNICAL DATA
Oscillating angle left/right
Deltasander no load oscillation frequency
Weight according EPTA-Procedure 01/2003
Noise/Vibration Information
Total vibration values (vector sum in the three axes) determined
according to EN 62841.
Vibration emission value a
h
OMNI 12C-PB
Delta sander head
Semi-circle saw
Strip saw
Uncertainty K =
OMNI 18C-PB
Delta sander head
Semi-circle saw
Strip saw
Uncertainty K =
OMNI 300-PB
Sound pressure level (K = 3 dB(A))
Sound power level (K =3 dB(A))
Wear ear protectors!
For technical data and approvals of powerbases for use with various
application heads please refer to the operating instructions of the
used powerbase.
WARNING
The vibration emission level given in this information sheet has been
measured in accordance with a standardised test given in EN 62841
and may be used to compare one tool with another. It may be used for
a preliminary assessment of exposure.
The declared vibration emission level represents the main applications
of the tool. However if the tool is used for different applications, with
different accessories or poorly maintained, the vibration emission may
differ. This may signifi cantly increase the exposure level over the total
working period.
An estimation of the level of exposure to vibration should also take
into account the times when the tool is switched off or when it is
running but not actually doing the job. This may signifi cantly reduce
the exposure level over the total working period.
Identify additional safety measures to protect the operator from the
effects of vibration such as: maintain the tool and the accessories,
keep the hands warm, organisation of work patterns.
WARNING! Read all safety warnings, instructions, illustrations
and specifications provided with this power tool. Failure to follow
all instructions listed below may result in electric shock, fire and/or
serious injury.
Save all warnings and instructions for future reference.
R&F side
Compatible with earlier generations of RYOBI, RIDGID or AEG
accessories. RYOBI is a trademark used under license from Ryobi
12V
Limited. RIDGID is a trademark of Ridgid, Inc. AEG is a registered
trademark used under license from AB Electrolux (publ).
18V
Compatible with FEIN accessories. FEIN is a registered trademark of
300W
C. & E. Fein GmbH.
OMNI-MTX
Compatible with CRAFTSMAN accessories. CRAFTSMAN is a
trademark of Stanley Black & Decker, Inc.
2.0/2.0 °
20000 min
-1
D side
470 g
Compatible with DREMEL accessories. DREMEL is a trademark of
Robert Bosch Tool Corporation.
SAFETY INSTRUCTIONS
Hold the power tool by insulated gripping surfaces, when
performing an operation where the cutting accessory may
a
8.0 m/s
2
contact hidden wiring or its own cord. Cutting accessory contacting
h
4.8 m/s
2
a "live" wire may make exposed metal parts of the power tool "live"
9.0 m/s
2
and could give the operator an electric shock.
1.5 m/s
2
Use clamps or another practical way to secure and support the
workpiece to a stable platform. Holding the workpiece by hand or
a
7.4 m/s
2
against your body leaves it unstable and may lead to loss of control.
h
5.5 m/s
2
When working in walls ceiling, or floor, take care to avoid electric
8. 9 m/s
2
cables and gas or waterpipes.
1.5 m/s
2
The dust produced when using this tool may be harmful to health. Do
not inhale the dust. Use a dust absorption system and wear a suitable
92 dB(A)
dust protection mask. Remove deposited dust thoroughly, e.g. with a
103 dB(A)
vacuum cleaner.
Remove the battery pack before starting any work on the machine.
Always disconnect the plug from the socket before carrying out any
work on the machine.
Dust from certain paints, coatings, and materials may cause irritation
or allergic reactions. Dust from wood such as oak, beech, MDF, and
others are carcinogenic. Only qualified specialists should be allowed
to use the product on materials containing asbestos.
Do not use compressed air to blow dust or debris. This practice is
dangerous and can cause dirt and grit to be blasted into someone's
eyes, causing serious injury.
RESIDUAL RISkS
Even when the product is used as prescribed, it is still impossible
to completely eliminate certain residual risk factors. The following
hazards may arise and the operator should pay special attention to
avoid the following:
Injury caused by dust and derbis
●
While using the product, considerable dust and fine particles will
be produced. Use the dust collection device and connect a dust
extraction vacuum during use.
●
Wear eye protection at all times.
●
Wear respiratory protection masks containing filters appropriate
to the materials being worked. Ensure adequate workplace
ventilation.
●
Do not eat, drink or smoke in the work area.
Injury caused by noise and vibration
●
Wear ear protection.
11
11
Advertisement
