Table of Contents
Advertisement
TECHNICAL DATA
Type
Battery voltage
Fastener type
Length
Width
Magazine capacity
Weight without battery pack
Noise Information
Measured values determined according to EN 60745. Typically, the A-weighted noise
levels of the tool are:
Sound pressure level / Uncertainty
Sound power level / Uncertainty
Wear ear protection!
Vibration Information
Vibration total values (triaxial vector sum) determined according to EN 60745.
Vibration emission value / Uncertainty
WARNING!
The declared vibration total values and the declared noise emission values given in this instruction manual have been measured in
accordance with a standardised test and may be used to compare one tool with another. They may be used for a preliminary assessment of
exposure.
The declared vibration and noise emission values represent the main applications of the tool. However, if the tool is used for different
applications, used with different accessories, or poorly maintained, the vibration and noise emission may differ. These conditions may
significantly increase the exposure levels over the total working period.
An estimation of the level of exposure to vibration and noise should take into account the times when the tool is turned off or when it is
running idle. These conditions may significantly reduce the exposure level over the total working period.
Identify additional safety measures to protect the operator from the effects of vibration and noise, such as maintaining the tool and the
accessories, keeping the hands warm (in case of vibration), and organising work patterns.
COMPATIBLE BATTERY PACKS (NOT INCLUDED)
L1820R
A18B4
L1820S
L1840R
A18FB2
A18FB4
L1825R
L1850R
L1830R-X5
A18FB5
Use AEG 18V battery and charger only
WARNING! Read all safety warnings, instructions,
illustrations and specifications provided with this power tool.
Failure to follow all instructions listed below may result in electric
shock, fire, and/or serious injury. Save all warnings and instruction
for future reference.
STAPLER SAFETY WARNINGS
Always assume that the tool contains fasteners. Careless
handling of the stapler can result in unexpected firing of fasteners
and personal injury.
Do not point the tool towards yourself or anyone nearby.
Unexpected triggering will discharge the fastener, causing an injury.
Do not actuate the tool unless the tool is placed firmly against
the workpiece. If the tool is not in contact with the workpiece, the
fastener may be deflected away from your target.
Disconnect the tool from the power source when the fastener
jams in the tool. While removing a jammed fastener, the stapler
may be accidentally activated if it is plugged in.
Use caution while removing a jammed fastener. The mechanism
may be under compression and the fastener may be forcefully
discharged while attempting to free a jammed condition.
Do not use this stapler for fastening electrical cables. It is
not designed for electric cable installation and may damage the
insulation of electric cables, thereby causing electric shock or fire
hazards.
ADDITIONAL SAFETY WARNINGS
The product is designed for single-hand use. Do not hold the
L1860R
product by the front of the magazine. Do not put hands, head, or
L1860R-X5
other parts of your body near the bottom of the magazine where the
L1890R
staple exits the product as serious personal injury could be caused.
Always ensure that the workpiece contact is fully positioned above
the workpiece. Partially positioning the workpiece contact above the
workpiece could cause the staple to completely miss the workpiece
and result in serious personal injury.
Do not drive staples near the edge of the material. The workpiece
may split, causing the staple to ricochet, injuring you or a coworker.
Be aware that the staple may follow the grain of the wood, causing
it to protrude from the side of the work material or deflect, possibly
causing injury.
Keep hands and body parts clear of the immediate work area.
Hold the workpiece with clamps when necessary to keep hands
and body out of potential harm. Make sure that the workpiece is
properly secured before pressing the fastener against the material.
The workpiece contact may cause the work material to shift
unexpectedly.
Keep face and body parts away from the back of the tool cap when
working in restricted areas. Sudden recoil can result in impact to the
body, especially when stapling into hard or dense material.
During normal use, the product will recoil immediately after driving a
fastener. This is a normal function of the product. Do not attempt to
prevent the recoil by holding the stapler against the workpiece.
Grip the handle firmly, let the product do the work and do not place a
second hand on top of the product or near the exhaust at any time.
Failure to heed this warning can result in serious personal injury.
Do not drive fasteners on top of other fasteners or with the product
at an overly steep angle as this may cause deflection of fasteners,
which could cause injury.
Always check the work area for hidden wiring, gas lines, and water
lines before using the product on such work area.
Adjust the driving depth of the staple before the actual work. It is
advisable to test the depth on a scrap workpiece to determine the
required depth for the application.
A18FST500
Stapler
18 V
Staples
6.35 - 14.3 mm
9.5 mm
88 staples
1.39 kg
L
=77.0 dB (A) / K
=3 dB(A)
pA
pA
L
=88.0 dB (A) / K
=3 dB(A)
WA
WA
a
=3.3 m/s
/ K=1.5 m/s
2
2
h
7
Advertisement
Table of Contents
