Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Keysight Technologies E5055A SSA-X
Summary of Contents for Keysight Technologies E5055A SSA-X
- Page 1 Keysight E5055A SSA-X Signal Source Analyzer Installation Guide...
- Page 2 FAR and the DFARS agreement and written consent from used or copied only in accordance and are set forth specifically in Keysight Technologies, Inc. as with the terms of such license. writing elsewhere in the EULA. governed by United States and...
-
Page 3: Caution
When you notice any of the unusual conditions listed below, immediately terminate operation and disconnect the power cable. Contact your local Keysight Technologies sales representative or authorized service company for repair of the instrument. If you continue to operate without repairing the instrument, there is a potential fire or shock hazard to the operator. -
Page 4: Manufacturer's Declaration
European Directives, and carries the CE marking accordingly: • The Low Voltage Directive 2014/35/EU • The EMC Directive 2014/30/EU • The RoHS Directive 2011/65/EU To obtain Declaration of Conformity, please contact your local Keysight Technologies sales office, agent or distributor. Keysight E5055A SSA-X Signal Source Analyzer... -
Page 5: Safety Notice Supplement
• This equipment is tested in stand-alone condition and in combination with the accessories supplied by Keysight Technologies against the requirement of the standards described in the Declaration of Conformity. If it is used as a system component, compliance of related regulations and safety requirements are to be confirmed by the builder of the system. -
Page 6: General Safety Precautions
To avoid the danger of introducing additional hazards, do not install substitute parts or perform unauthorized modifications to the instrument. Return the instrument to a Keysight Technologies Sales and Service Office for service and repair to ensure that safety features are maintained in operational condition. -
Page 7: Safety Symbols
Certification Keysight Technologies certifies that this product met its published specifications at the time of shipment from the factory. Keysight Technologies further certifies that its calibration measurements are traceable to the United States National Institute of Standards and Technology, to the extent allowed by the Institution’s calibration facility or by the calibration facilities of other... -
Page 8: Documentation Warranty
Exclusive Remedies The remedies provided herein are Buyer’s sole and exclusive remedies. Keysight Technologies shall not be liable for any direct, indirect, special, incidental, or consequential damages, whether based on contract, tort, or any other legal theory. -
Page 9: Manuals For E5055A
Service Guide The service manual provides information about the parts, troubleshooting, performance test, adjustment and service menu. Keysight E5055A SSA-X Signal Source Analyzer... - Page 10 Caution Manuals for E5055A Keysight E5055A SSA-X Signal Source Analyzer...
-
Page 11: Table Of Contents
Contents Table of Contents Caution ..............3 Safety Summary . - Page 12 Contents Keysight E5055A Installation Guide...
-
Page 13: Installation
Keysight E5055A SSA-X Signal Source Analyzer Installation Guide Installation This chapter provides information about how to set up the Keysight E5055A. Checking the Shipment After you receive the analyzer, carry out checks during unpacking according to the following procedure. When unpacking the analyzer, if the exterior of the analyzer (such as the cover, front/rear panel, LCD screen, power switch, and port connectors) appear to be damaged during transport, do not turn on the power switch. -
Page 14: Environmental Requirements
4. A fault has been detected in the subsequent operation check of the analyzer. If an abnormality is detected in step 1, contact the company that transported the analyzer as well as your nearest Keysight Technologies sales and service office. Environmental Requirements Set up the E5055A where the following environmental requirements are met. -
Page 15: Protection Against Electrostatic Discharge (Esd)
AC outlet or the E5055A unit. When installing the E5055A, ensure that there is sufficient free space around the unit to permit quick disconnection of the plug (from AC outlet or E5055A unit) in case of emergency. Keysight E5055A SSA-X Signal Source Analyzer... -
Page 16: Power Supply
Use the supplied power cable with grounding wire to securely ground the E5055A. For power cord list and options, refer to www.keysight.com/find/powercords. Keysight E5055A SSA-X Signal Source Analyzer... -
Page 17: Blown Fuses
Technologies Customer contact center listed at the end of this guide. The E5055A uses the following fuse types: UL/CSA Type, 250 V 20 A DO NOT replace the fuse yourself; doing this may expose you to electrical shock. Keysight E5055A SSA-X Signal Source Analyzer... -
Page 18: Starting The E5055A
"safe mode." If this occurs, first shut down the system to set it to the standby state and then turn ON the power supply again to start up the system in normal mode. Keysight E5055A SSA-X Signal Source Analyzer... -
Page 19: Disconnection From Supply Source
“Ensuring Adequate Free Space around Analyzer for Immediate Disconnection of Power Cable in Case of Emergency” on page When turning the power OFF under normal circumstances, always follow the methods described in “Turning the Power OFF” on page Keysight E5055A SSA-X Signal Source Analyzer... -
Page 20: Initial Registration Of E5055A
When the Windows agreement message box appears, click Agree. The rest of the procedure runs automatically. The Touch Screen does not require any calibration and it works from the very first time you use the E5055A. Keysight E5055A SSA-X Signal Source Analyzer... -
Page 21: Troubleshooting
Keysight E5055A SSA-X Signal Source Analyzer Installation Guide 2 Troubleshooting This chapter describes the troubleshooting during start up and the procedure of the operating system (OS) recovery when the Windows OS has been damaged. Troubleshooting during Startup When you encounter the problem during start up, see Table 2-1. -
Page 22: System Recovery
1. The default setting of the storage is recovered during the system recovery. For the storage that had failed earlier and had been replaced (after purchase), its default setting may not be the same as the factory state. Keysight E5055A SSA-X Signal Source Analyzer... -
Page 23: Procedure To Execute The Factory Recovery
After several seconds, the next screen appears automatically even if you do not press any key. Step 6. Type 2 to select Recover the original factory system image option and press [Enter]. Figure 2-1 System recovery selection screen Keysight E5055A SSA-X Signal Source Analyzer... - Page 24 If the Software End User License Agreement appears during the system recovery. Press [Agree]. Never turn OFF the power during the system recovery because doing so may cause serious damage to the E5055A. Keysight E5055A SSA-X Signal Source Analyzer...
- Page 25 Index Index accessories assistance cable power cable options documentation warranty environmental requirements operation environment ventilation space error-correction temperature range Exclusive Remedies Inspection checking the shipment power check the power supply disconnection from supply source power cable options verification and connection of power cable safety symbols shutdown...
- Page 26 Index Keysight E5055A Installation Guide...
- Page 27 This information is subject to change without notice. © Keysight Technologies 2022 Edition 1, March 2022 www.keysight.com...
Need help?
Do you have a question about the E5055A SSA-X and is the answer not in the manual?
Questions and answers