Page 1
Operating Instructions Ultrasonic Homogenisers Ultrasonic Homogeniser HD 4100 valid for: HD 4050 Volume: 0.5 ml – 100 ml HD 4100 Volume: 2 ml - 200 ml HD 4200 Volume: 5 ml - 1000 ml HD 4400 Volume: 100 ml - 3000 ml 51376-012 en/2022-09...
Page 2
Copyright & limitation of liability This document may not be reproduced, whether in full or in part, without the prior approval of BANDELIN electronic GmbH & Co. KG, hereinafter "BANDELIN". The German language original is the binding version of this document. Any diff erences in the translation are not binding and have no legal eff...
Page 3
Identifi es instructions that must be carried out Instructions in the described sequence. 51376-012 en/2022-09 3 / 42 1 electronic GmbH & Co. KG • Heinrichstraße 3-4 • 12207 Berlin • Deutschland • info@bandelin.com...
General use ........................24 Selecting a suitable probe .................... 26 4.3.1 Mounting and dismounting of the probes ..............27 4 / 42 51376-012 en/2022-09 1 electronic GmbH & Co. KG • Heinrichstraße 3-4 • 12207 Berlin • Deutschland • info@bandelin.com...
Page 5
Taking the unit out of service ..................40 Keyword index – not applicable – ................. 40 Informative annexes Spanner for mounting/dismounting 51376-012 en/2022-09 5 / 42 1 electronic GmbH & Co. KG • Heinrichstraße 3-4 • 12207 Berlin • Deutschland • info@bandelin.com...
- 2011/ 65 / EU - RoHS Directive A declaration of conformity can be requested from the manufacturer by providing the serial number. 51376-012 en/2022-09 7 / 42 1 electronic GmbH & Co. KG • Heinrichstraße 3-4 • 12207 Berlin • Deutschland • info@bandelin.com...
In the case of highly-viscous media, this can result in the desired amplitude not always being reached. The power depends on the connected ultrasonic converter. 8 / 42 51376-012 en/2022-09 1 electronic GmbH & Co. KG • Heinrichstraße 3-4 • 12207 Berlin • Deutschland • info@bandelin.com...
Permissible ambient temperature: 5 to 40 °C Altitude: up to 2000 m above sea level No dewing. Only for indoor operation. 51376-012 en/2022-09 9 / 42 1 electronic GmbH & Co. KG • Heinrichstraße 3-4 • 12207 Berlin • Deutschland • info@bandelin.com...
• When connecting a changeover contact (toggle function) to connector 1, the make time must be > 100 ms. 10 / 42 51376-012 en/2022-09 1 electronic GmbH & Co. KG • Heinrichstraße 3-4 • 12207 Berlin • Deutschland • info@bandelin.com...
Page 11
The inputs and outputs of the remote control connector and RS-232 interface may only be connected with devices of protection class I that are connected to the same mains supply circuit. 51376-012 en/2022-09 11 / 42 1 electronic GmbH & Co. KG • Heinrichstraße 3-4 • 12207 Berlin • Deutschland • info@bandelin.com...
• Only use the prescribed tool for mounting and dismounting (see appendix A). • Do not use any bent probes ( unstable operation, loss of power). 12 / 42 51376-012 en/2022-09 1 electronic GmbH & Co. KG • Heinrichstraße 3-4 • 12207 Berlin • Deutschland • info@bandelin.com...
Before start-up, the ultrasonic homogeniser should be allowed to stand for 2 hours at its operating location so that it can adjust to the ambient conditions. 51376-012 en/2022-09 13 / 42 1 electronic GmbH & Co. KG • Heinrichstraße 3-4 • 12207 Berlin • Deutschland • info@bandelin.com...
Connect to a grounded socket only if type is suitable. 14 / 42 51376-012 en/2022-09 1 electronic GmbH & Co. KG • Heinrichstraße 3-4 • 12207 Berlin • Deutschland • info@bandelin.com...
fi elds within the parameter using the arrow key . Editing mode is cancelled with the "SET" or "START" keys. 16 / 42 51376-012 en/2022-09 1 electronic GmbH & Co. KG • Heinrichstraße 3-4 • 12207 Berlin • Deutschland • info@bandelin.com...
0.000 kJ Energy 0.000 kJ START STOP back to stand-by mode proceed to next set value or operating parameter 51376-012 en/2022-09 17 / 42 1 electronic GmbH & Co. KG • Heinrichstraße 3-4 • 12207 Berlin • Deutschland • info@bandelin.com...
The pulse period duration is the sum of the turn-on and turn-off time t = t 18 / 42 51376-012 en/2022-09 1 electronic GmbH & Co. KG • Heinrichstraße 3-4 • 12207 Berlin • Deutschland • info@bandelin.com...
Pulsation 4.0s 4.0s temperature sensor Temperature 31°C no sensor: ---°C Energy 0.000 kJ START STOP back to stand-by mode 51376-012 en/2022-09 19 / 42 1 electronic GmbH & Co. KG • Heinrichstraße 3-4 • 12207 Berlin • Deutschland • info@bandelin.com...
(inverse presentation) instead of the current program (prog). Note: In this operating mode, no changes can be made to the settings in stand-by or ultrasonic operation. 22 / 42 51376-012 en/2022-09 1 electronic GmbH & Co. KG • Heinrichstraße 3-4 • 12207 Berlin • Deutschland • info@bandelin.com...
• The display value for the energy is a guideline value and does not correspond to the acoustic energy actually applied. 51376-012 en/2022-09 23 / 42 1 electronic GmbH & Co. KG • Heinrichstraße 3-4 • 12207 Berlin • Deutschland • info@bandelin.com...
Set the immersion depth for the probe (approx. 10 -20 mm). If necessary, connect the temperature sensor and position it in the medium. 24 / 42 51376-012 en/2022-09 1 electronic GmbH & Co. KG • Heinrichstraße 3-4 • 12207 Berlin • Deutschland • info@bandelin.com...
Page 25
Clean the probe and check the wear on the sound emitting surface at regular intervals, see chapter 5.1. 51376-012 en/2022-09 25 / 42 1 electronic GmbH & Co. KG • Heinrichstraße 3-4 • 12207 Berlin • Deutschland • info@bandelin.com...
The information may change after the probes have been technically updated. The data stored in the program is always valid! 26 / 42 51376-012 en/2022-09 1 electronic GmbH & Co. KG • Heinrichstraße 3-4 • 12207 Berlin • Deutschland • info@bandelin.com...
The tool required for mounting/ dismounting is included in the scope of delivery. Mounting surfaces are the contact surfaces between the standard/booster horn and the probe. 51376-012 en/2022-09 27 / 42 1 electronic GmbH & Co. KG • Heinrichstraße 3-4 • 12207 Berlin • Deutschland • info@bandelin.com...
One sickle spanner is part of the scope of delivery of one standard/booster horn. Ultrasonic converter Step/booster horn Vigorously turn sickle spanner HS 40/42 long, in the opposite direction 30 / 42 51376-012 en/2022-09 1 electronic GmbH & Co. KG • Heinrichstraße 3-4 • 12207 Berlin • Deutschland • info@bandelin.com...
Page 31
The ultrasonic oscillating system and its electrical connections would be damaged as a result. 51376-012 en/2022-09 31 / 42 1 electronic GmbH & Co. KG • Heinrichstraße 3-4 • 12207 Berlin • Deutschland • info@bandelin.com...
During extended periods without use, the ultrasonic homogeniser should be stored in a cool, dry place. The ultrasonic converter should be covered in order to protect the electronics from outside contamination. 51376-012 en/2022-09 33 / 42 1 electronic GmbH & Co. KG • Heinrichstraße 3-4 • 12207 Berlin • Deutschland • info@bandelin.com...
GM has dropped to < 50 °C. 51376-012 en/2022-09 35 / 42 1 electronic GmbH & Co. KG • Heinrichstraße 3-4 • 12207 Berlin • Deutschland • info@bandelin.com...
Page 36
4.3.1. Wrong resonance frequency? Conduct frequency scan, see chapter 6.2 (search frequency). 36 / 42 51376-012 en/2022-09 1 electronic GmbH & Co. KG • Heinrichstraße 3-4 • 12207 Berlin • Deutschland • info@bandelin.com...
The ultrasonic oscillating system and its electrical connections would be damaged as a result. 51376-012 en/2022-09 37 / 42 1 electronic GmbH & Co. KG • Heinrichstraße 3-4 • 12207 Berlin • Deutschland • info@bandelin.com...
03.01 - 2016-08-085 The software version provided here is illustrative, the actual specifi cations may diff er. 38 / 42 51376-012 en/2022-09 1 electronic GmbH & Co. KG • Heinrichstraße 3-4 • 12207 Berlin • Deutschland • info@bandelin.com...
The sonication of liquids generates noise. The sound proof box dampens the noise emission by approx. 30 dB(AU). LS 40 51376-012 en/2022-09 39 / 42 1 electronic GmbH & Co. KG • Heinrichstraße 3-4 • 12207 Berlin • Deutschland • info@bandelin.com...
• Metal accessories such as probes or standard horns should be decontaminated and disposed of as metal waste. • The packaging is recyclable. Keyword index – not applicable – BANDELIN electronic GmbH & Co. KG www.bandelin.com Zertifi ziert nach Heinrichstraße 3 – 4 info@bandelin.com...
Page 41
Spanner for mounting/dismounting Probes and standard/booster horns are highly-sensitive parts that must be mounted and dismounted with the greatest amount of care. For this reason, only use the following spanners for the mounting/dismounting of probes from standard/booster horns, as well as of standard/booster horns from the ultrasonic converter: Spanner Usage Type...
Need help?
Do you have a question about the SONOPULS HD 4050 and is the answer not in the manual?
Questions and answers