Table of Contents
Advertisement
NOPLF (No operation / page break) ..................... 5-43
[O]
Operation error ..................................................... 3-10
Operation results inversion (INV) ......................... 5-12
Operation results pop (MPP) .................................. 5-9
Operation results pulse
Edge relay memory (EGF, EGP) ..................... 5-15
Memory (MEF, MEP) ....................................... 5-14
Operation results push (MPS) ................................ 5-9
Operation results read (MRD) ................................ 5-9
Operation start (LD, LDI) ........................................ 5-2
OR (=, , >, =) (BIN 16-bit data comparisons) .......... 6-2
OR (=, <>, >, <=, <, >=)
(BIN 16-bit data comparisons) ................................ 6-2
OR (A contact parallel connection) ......................... 5-2
OR (D=, D<>, D>, D<=, D<, D>=)
(BIN 32-bit data comparisons) ................................ 6-4
OR inverse (ORI) .................................................... 5-2
ORB (Ladder block parallel connections) ............... 5-7
ORF (Pulse parallel connection / trailing edge) ...... 5-5
ORI (B contact parallel connection) ........................ 5-2
ORP (Pulse parallel connection / leading edge) ..... 5-5
Other Instructions ................................................. 5-43
OUT
Annunciator output (OUT F) ............................ 5-25
Counters (OUT C) ........................................... 5-23
High speed retentive timer (OUTH ST) ........... 5-19
High speed timer (OUTH T) ............................. 5-19
Low speed retentive timer (OUT ST) ............... 5-19
Low speed timer (OUT T) ................................ 5-19
Output (OUT) ................................................... 5-17
Output Instruction (OUT) ...................................... 5-17
Output Instructions List ........................................... 2-7
Output Reverse (FF) ............................................. 5-36
[P]
PAGE break (NOPLF) .......................................... 5-43
PAGE n (No operation) ......................................... 5-43
Parallel connection (OR,ORI) ................................. 5-2
Parallel connection (ORB) ...................................... 5-7
PLF (Trailing edge output) .................................... 5-33
PLS (Leading edge output) ................................... 5-33
Pop (MPP) .............................................................. 5-9
Pulse (PLS) .......................................................... 5-33
Pulse conversion
(EGP, EGF) ..................................................... 5-15
(MEF, MEP) ..................................................... 5-14
Pulse operation start (LDP, LDF) ........................... 5-5
Pulse parallel connection (ORP, ORF) ................... 5-5
Pulse series connection (ANDP, ANDF) ................ 5-5
Push (MPS) ............................................................ 5-9
Index-4
[Q]
QSCPU Dedicated Instruction List ........................2-16
[R]
Read (MRD) ............................................................5-9
Reading an error code ............................................9-3
Reset (RST) ..........................................................5-29
Resetting devices (RST) .......................................5-29
Resetting the annunciators (RST F) .....................5-31
Resetting the master control (MCR) .....................5-38
Reverse
Bit device output (FF) ......................................5-36
Operation results (INV) ....................................5-12
RST
Resetting devices (RST) ..................................5-29
Resetting the annunciators (RST F) ................5-31
[S]
S.QSABORT (Forced control stop instruction ) ......8-2
Sequence Instruction List .......................................2-5
Series connection (ANB) ........................................5-7
Series connection (AND, ANI) ................................5-2
SET
Setting devices (SET) ......................................5-27
Setting the annunciators (SET F) ....................5-31
Setting devices .....................................................5-27
Setting the master control (MC) ............................5-38
Step Number .........................................................3-13
Subset Processing ..................................................3-9
Subtraction
BIN 16-bit data (-) ..............................................6-6
BIN 32-bit data (D-) ..........................................6-10
[T]
Timers (OUT T) .....................................................5-19
Trailing edge output (PLF) ....................................5-33
Types of Instructions ...............................................2-2
[W]
WAND (Logical products with 16-bit data) ..............7-3
WOR (Logical sums of 16-bit data) .........................7-8
Word data ...............................................................3-4
Word device bit designation ....................................3-3
WXNR (16-bit data exclusive NOR operation) ......7-16
WXOR (16-bit exclusive OR operations) ..............7-12
Advertisement
Table of Contents
