Shop fox W1680 Owner's Manual
  1. Manuals
  2. Brands
  3. Shop fox Manuals
  4. Power Tool
  5. SHOP FOX W1680
  6. Owner's manual

Shop fox W1680 Owner's Manual

17" drill press
Hide thumbs Also See for W1680:
Table of Contents

Advertisement

Quick Links

Download this manual
MODEL W1680
17" DRILL PRESS
OWNER'S MANUAL
(FOR MODELS MANUFACTURED SINCE 06/22)
Phone: (360) 734-3482 • Online Technical Support: techsupport@woodstockint.com
COPYRIGHT © 2000 BY WOODSTOCK INTERNATIONAL, INC., REVISED SEPTEMBER, 2022 (CS)
WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE OR FORM WITHOUT
THE WRITTEN APPROVAL OF WOODSTOCK INTERNATIONAL, INC.
***Keep for Future Reference***
V2.09.22
#4938CR Printed in China

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the W1680 and is the answer not in the manual?

Questions and answers

Related Manuals for Shop fox W1680

Summary of Contents for Shop fox W1680

  • Page 1 MODEL W1680 17" DRILL PRESS OWNER'S MANUAL (FOR MODELS MANUFACTURED SINCE 06/22) Phone: (360) 734-3482 • Online Technical Support: techsupport@woodstockint.com COPYRIGHT © 2000 BY WOODSTOCK INTERNATIONAL, INC., REVISED SEPTEMBER, 2022 (CS) WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE OR FORM WITHOUT THE WRITTEN APPROVAL OF WOODSTOCK INTERNATIONAL, INC.
  • Page 2 This manual provides critical safety instructions on the proper setup, operation, maintenance, and service of this machine/tool. Save this document, refer to it often, and use it to instruct other operators. Failure to read, understand and follow the instructions in this manual may result in fire or serious personal injury—including amputation, electrocution, or death.

  • Page 3: Table Of Contents

    Contents INTRODUCTION........2 ACCESSORIES........34 Woodstock Technical Support ....2 Drill Press Accessories ......34 Controls & Components ......6 MAINTENANCE........35 SAFETY..........8 General .......... 35 Standard Machinery Safety Instructions ..8 Cleaning & Protecting ......35 Additional Safety for Drill Presses ... 10 Inspecting/Replacing Belts ....

  • Page 4: Introduction

    Model W1680 (For Machines Mfd. Since 06/22) INTRODUCTION Woodstock.Technical.Support This machine has been specially designed to provide many years of trouble-free service. Close attention to detail, ruggedly built parts and a rigid quality control program assure safe and reliable operation.
  • Page 5 Switch Type............. Toggle Safety Switch w/Removable Key Motors Main Horsepower....................1 HP Phase....................Single‐Phase Amps......................10A Speed....................1725 RPM Type................. TEFC Capacitor‐Start Induction Power Transfer ................... V‐Belt Drive Bearings............... Shielded & Permanently Lubricated Centrifugal Switch/Contacts Type..............Internal Model W1680 Machine Specifications, Page 1 of 3...
  • Page 6 Base Width....................11 in. Mobile Base..................... D2057A Column Diameter..................3.150 in. Depth Stop Type............Threaded Rod with Positive Stop Has Work Light....................Yes Light Socket Type................110V, Std Bulb Maximum Bulb Wattage................... 60W Model W1680 Machine Specifications, Page 2 of 3...
  • Page 7 Model W1680 (For Machines Mfd. Since 06/22) Identification Become familiar with the names and locations of the controls and features shown below to better understand the instructions in this manual. Belt Cover Control Panel Belt Tension Controls Motor Depth Stop...

  • Page 8: Controls & Components

    Model W1680 (For Machines Mfd. Since 06/22) Controls.&.Components Refer to the Figures.1–5 and the following descriptions to become familiar with the basic controls and components of this machine. Understanding these items and how they work will help you understand the rest of the manual and stay safe when operating this machine.
  • Page 9 Model W1680 (For Machines Mfd. Since 06/22) E.. Spindle.Handle.(1.of.3): Moves spindle down when pulled down. Spindle automatically returns to top position when released. F.. Belt.Tension.Lock.Knob.(1.of.2):.Locks motor position to keep V-belts tensioned. G.. Belt.Tension.Lever:.Adjusts motor position to tension and release V-belts.

  • Page 10: Safety

    Model W1680 (For Machines Mfd. Since 06/22) SAFETY SAFETY For.Your.Own.Safety, Read.Manual.Before.Operating.Machine The. purpose. of. safety. symbols. is. to. attract. your. attention. to. possible. hazardous. conditions.. This. manual.uses.a.series.of.symbols.and.signal.words.intended.to.convey.the.level.of.importance.of.the. safety.messages..The.progression.of.symbols.is.described.below..Remember.that.safety.messages.by. themselves. do. not. eliminate. danger. and. are. not. a. substitute. for. proper. accident. prevention. mea- sures—this.responsibility.is.ultimately.up.to.the.operator!
  • Page 11 Model W1680 (For Machines Mfd. Since 06/22) WEARING.PROPER.APPAREL..Do not wear FORCING.MACHINERY..Do not force machine. It clothing, apparel, or jewelry that can become will do the job safer and better at the rate for entangled in moving parts. Always tie back which it was designed.

  • Page 12: Additional Safety For Drill Presses

    Model W1680 (For Machines Mfd. Since 06/22) Additional.Safety.for.Drill.Presses Serious injury or death can occur from getting clothing, jewelry, or long hair entangled in rotating spindle or bit/cutting tool. Contact with rotating bit/cutting tool can result in severe cuts or ampu- tation of fingers.

  • Page 13: Electrical

    Model W1680 (For Machines Mfd. Since 06/22) ELECTRICAL Circuit.Requirements This machine must be connected to the correct size and type of power supply circuit, or fire or electrical damage may occur. Read through this section to determine if an The machine must be properly set up adequate power supply circuit is available.

  • Page 14: Grounding Requirements

    Model W1680 (For Machines Mfd. Since 06/22) Grounding.Requirements This machine MUST be grounded. In the event of certain types of malfunctions or breakdowns, grounding provides GROUNDED 110V 5-15 RECEPTACLE a path of least resistance for electric current to travel—in order to reduce the risk of electric shock.

  • Page 15: Setup

    Model W1680 (For Machines Mfd. Since 06/22) SETUP Unpacking This machine has been carefully packaged for safe transportation. If you notice the machine has been damaged during shipping, please contact your authorized This machine presents Shop Fox dealer immediately. serious...

  • Page 16: Hardware Recognition Chart

    Model W1680 (For Machines Mfd. Since 06/22) Hardware.Recognition.Chart USE THIS CHART TO IDENTIFY HARDWARE DURING THE INVENTORY/ASSEMBLY ⁄ " ⁄ " ⁄ " PROCESS. ⁄ " ⁄ " ⁄ " ⁄ " ⁄ " ⁄ " ⁄ " ⁄ "...

  • Page 17: Inventory

    Model W1680 (For Machines Mfd. Since 06/22) Inventory The following is a list of items shipped with your machine. Before beginning setup, lay these items out and inventory them. Note: If you cannot find an item on this list, carefully check around/inside the machine and packaging materials.

  • Page 18: Cleaning Machine

    Model W1680 (For Machines Mfd. Since 06/22) Cleaning.Machine To prevent corrosion during shipment and storage of your machine, the factory has coated the bare metal surfaces of your machine with a heavy-duty rust prevention compound. Gasoline.and.petroleum. products.have.low.flash. If you are unprepared or impatient, this compound can points.and.can.explode.

  • Page 19: Machine Placement

    Model W1680 (For Machines Mfd. Since 06/22) Machine.Placement Weight.Load Physical.Environment Refer to the Machine.Specifications for the The physical environment where your machine is weight of your machine. Make sure that the operated is important for safe operation and the surface upon which the machine is placed will longevity of its components.

  • Page 20: Anchoring To Floor

    Model W1680 (For Machines Mfd. Since 06/22) Anchoring.to.Floor Number.of.Mounting.Holes........4 Diameter.of.Mounting.Hardware......⁄ " Anchoring machinery to the floor prevents tipping or shifting and reduces vibration that may occur during operation, resulting in a machine that runs slightly quieter and feels more solid.

  • Page 21: This. Machine

    Model W1680 (For Machines Mfd. Since 06/22) Joining.Drill.Chuck.&. Arbor An arbor is included for the drill chuck that comes with this machine. The following procedure describes how to install the arbor in the chuck. After the arbor is installed in the drill chuck, it is very difficult to separate the assembly.

  • Page 22: Assembly

    Model W1680 (For Machines Mfd. Since 06/22) Assembly Before beginning the assembly process, refer to Items. Needed.for.Setup and gather everything you need. Ensure all parts have been properly cleaned of any heavy-duty rust-preventative applied at the factory (if applicable). Be sure to complete all steps in the assembly Column procedure prior to performing the Test.Run.or connecting...
  • Page 23 Model W1680 (For Machines Mfd. Since 06/22) 4. Position rack so end with gear teeth closest to end are facing downward (see Figure 14). Table Support Bracket 5. Insert rack into table support bracket so teeth face out and mesh with pinion (see Figure 14).
  • Page 24 Model W1680 (For Machines Mfd. Since 06/22) 10. Slide rack ring onto column with inside bevel in down position (see Figure.17). . 11.. Adjust ring until tip of rack fits inside bevel, and rack rotates freely when you rotate table support bracket around column.
  • Page 25 Model W1680 (For Machines Mfd. Since 06/22) 16.. Tighten (2) set screws shown in Figure.20 to secure headstock to column. Figure.20..Location of set screws. 17.. Thread (3) spindle handles into hub, as shown in Figure.21. 18.. Turn socket dust plug in light bulb socket behind...

  • Page 26: Test Run

    Model W1680 (For Machines Mfd. Since 06/22) Test.Run Once assembly is complete, test run the machine to ensure it is properly connected to power and safety components are functioning properly. Serious. injury. or. death. can. result. from. using. this. machine. BEFORE.

  • Page 27: Operations

    Model W1680 (For Machines Mfd. Since 06/22) OPERATIONS General This machine will perform many types of operations that are beyond the scope of this manual. Many of these operations can be dangerous or deadly if performed incorrectly. The instructions in this section are written with the understanding that the operator has the necessary knowledge and skills to operate this machine.

  • Page 28: Installing/Removing Arbor

    Model W1680 (For Machines Mfd. Since 06/22) Installing/Removing.Arbor Usually, once the chuck and arbor have been properly mounted together, they are considered semi-permanent connections. If you would like to install a different chuck, we recommend getting a new arbor for that chuck.
  • Page 29 Model W1680 (For Machines Mfd. Since 06/22) Removing.Arbor.from.Spindle Items.Needed. Towel or Cloth ...........1 Metal Hammer ...........1 Drift Key ............1 To.remove.arbor.from.spindle,.do.these.steps: 1. DISCONNECT MACHINE FROM POWER! 2. Rotate spindle handles until drift key slot is exposed in side of quill (see Figure 25).

  • Page 30: Installing/Removing Drill Bit

    Model W1680 (For Machines Mfd. Since 06/22) Installing/Removing. Drill.Bit Any drill bit you install in the chuck must be tight enough that it will not come loose during operation. Installing.Drill.Bit Tool.Needed. Chuck Key ............1 To.install.drill.bit,.do.these.steps: 1. DISCONNECT MACHINE FROM POWER! 2.

  • Page 31: Adjusting Table

    Model W1680 (For Machines Mfd. Since 06/22) Adjusting.Table You can adjust the table height, tilt, and rotation to accommodate for workpiece height or achieve special angles. If the table is not needed, loosen the support bracket lock lever to pivot the table to the back side of the column so you can support the workpiece on the base.

  • Page 32: Changing Spindle Speed

    2–7 1160 RPM 2–8 1510 RPM 1–7 1650 RPM 2–8 2180 RPM 1–8 3050 RPM The Model W1680 has 12 spindle speeds that operate between 150–3050 RPM. Refer to the speed chart located under the belt cover. Use.care.when.changing.V-belts.as.they. could.pinch.your.fingers..They.may.also. The speed chart above is included to help illustrate the be.
  • Page 33 Model W1680 (For Machines Mfd. Since 06/22) 5.. Use spindle speed chart under belt cover to move V-belts onto desired sheaves of pulleys (see Figure 32). Motor Idler Pulley — If V-belt is cracked, torn, excessively worn, or Pulley Spindle damaged, replace it.

  • Page 34: Calculating Spindle Speed For Drilling

    Model W1680 (For Machines Mfd. Since 06/22) Calculating.Spindle.Speed. for.Drilling Lubrication.Suggestions The chart shown in Figure 34 is intended as a guide only. Always follow the manufacturer's speed recommendations Wood ........None if provided with your drill bits, cutters, or hole saws.

  • Page 35: Adjusting Depth Stop

    Model W1680 (For Machines Mfd. Since 06/22) Adjusting.Depth.Stop The Model W1680 has a depth stop that allows you to drill repeat non-through holes to the same depth every time. The scale and indicator shows the depth in inches. The depth stop consists of a stud attached to the quill...

  • Page 36: Accessories

    Model W1680 (For Machines Mfd. Since 06/22) ACCESSORIES Drill.Press.Accessories The following drill press accessories may be available through your local Woodstock International Inc. Dealer. If you do not have a dealer in your area, these products are also available through online dealers.

  • Page 37: Maintenance

    • Lubricate quill and column racks. Cleaning.&.Protecting Cleaning the Model W1680 is relatively easy. Vacuum excess wood chips and sawdust, and wipe off the remaining dust with a dry cloth. If any resin has built up, use a resin dissolving cleaner to remove it.

  • Page 38: Lubrication

    Model W1680 (For Machines Mfd. Since 06/22) Lubrication Since all bearings are shielded and permanently lubricat- ed, simply leave them alone until they need to be replaced. Do not lubricate them. An essential part of lubrication is cleaning the components before lubricating them.
  • Page 39 Model W1680 (For Machines Mfd. Since 06/22) Quill.&.Column.Racks Lubrication Type ....... NLGI#2 Grease Lubrication Amount ........Thin Coat Lubrication Frequency ....90 Hrs. of Operation Move spindle all the way down to gain full access to the quill rack (see Figure 40), then clean teeth with mineral spirits, shop rags, and a brush.

  • Page 40: Service

    Model W1680 (For Machines Mfd. Since 06/22) SERVICE General This section covers the most common service adjustments or procedures that may need to be made during the life of your machine. If you require additional machine service not included in this section, please contact Woodstock International Technical Support at (360) 734-3482 or send e-mail to: techsupport@woodstockint.com.

  • Page 41: Tensioning Feed Shaft Return Spring

    Model W1680 (For Machines Mfd. Since 06/22) Tensioning.Feed.Shaft. Return.Spring The feed shaft return spring is adjusted at the factory; however, during the life of the drill press you may want to adjust the feed shaft return spring to a stronger If return spring should return pressure.

  • Page 42: Adjusting Quill Shaft Screw

    Model W1680 (For Machines Mfd. Since 06/22) 4... Pull cover outward just enough to disengage spring Locking Lug cover lock slot from locking lug (see Figure.45). 5... Rotate cover counterclockwise to increase spring tension, or let cover slowly unwind in clockwise direction to reduce spring tension.

  • Page 43: Troubleshooting

    Model W1680 (For Machines Mfd. Since 06/22) Troubleshooting The following troubleshooting tables cover common problems that may occur with this machine. If you need replacement parts or additional troubleshooting help, contact our Technical Support. Note: Before contacting Tech Support, find the machine serial number and manufacture date, and if available, your original purchase receipt.
  • Page 44 Model W1680 (For Machines Mfd. Since 06/22) Operation PROBLEM POSSIBLE.CAUSE CORRECTIVE.ACTION Tool falls out or 1. Chuck jaws loose. 1. Tighten chuck jaws. loose in chuck. 2. Excessive feed pressure. 2. Decrease feed pressure and allow chips to clear. Chuck and arbor 1.

  • Page 45: Electrical Safety Instructions

    Model W1680 (For Machines Mfd. Since 06/22) Electrical.Safety.Instructions These pages are current at the time of printing. However, in the spirit of improvement, we may make changes to the electrical systems of future machines. Compare the manufacture date of your machine to the one stated in this manual, and study this section carefully.

  • Page 46: Wiring Diagram

    Model W1680 (For Machines Mfd. Since 06/22) Wiring.Diagram 110V Motor Headstock Light ON/OFF Switch Ground XL601-101 CNXLE T125 ON/OFF Switch KEDU HY18 Start Capacitor Light CD60 Socket 250V 300uF Ground Ground Neutral Light Bulb 60W Read Page 43 STOP Before...

  • Page 47: Parts

    Model W1680 (For Machines Mfd. Since 06/22) PARTS Main 58-1 58-2 58-3 14-1 23A-3 23A-2 111-2 23A-4 111-4 111-2 111-1 23A-3 23A-1V2 111-3 111-1 111-5 -45-...
  • Page 48 Model W1680 (For Machines Mfd. Since 06/22) Main.Parts.List PART # DESCRIPTION REF PART # DESCRIPTION X1680001V2 BASE V2.04.03 X1680051 HEX BOLT M8-1.25 X 16 X1680002 HEX BOLT M12-1.75 X 30 X1680052 SHIFTER X1680003 RACK 31-15/16" X1680053 SLIDE BAR X1680004A COLUMN V2.04.03...
  • Page 49 Model W1680 (For Machines Mfd. Since 06/22) Main.Parts.List.(Cont.) PART # DESCRIPTION PART # DESCRIPTION X1680101 HEX WRENCH 4MM 111-3 X1680111-3 TAP SCREW M2.2 X 4.5 X1680102 HEX WRENCH 5MM 111-4 X1680111-4 HEX BOLT M5-.8 X 12 X1680103 DRIFT KEY 111-5 X1680111-5 WING NUT M5-.8...

  • Page 50: Labels & Cosmetics

    Model W1680 (For Machines Mfd. Since 06/22) Labels.&.Cosmetics 105V2 WARNING! WARNING! WARNING! READ and UNDERSTAND ACCIDENTAL INJURY EYE INJURY MANUAL to avoid serious HAZARD! HAZARD! injury! If a manual is not Disconnect power available, DO NOT use supply before Always wear safety...

  • Page 51: Warranty

    Woodstock International, Inc. will repair, replace, or arrange for a dealer refund, at its expense and option, the Shop Fox machine or machine part proven to be defective for its designed and intended use, provided that the original owner returns the product prepaid to an authorized warranty or repair facility as designated by our Bellingham, Washington office with proof of their purchase of the product within two years, and provides Woodstock International, Inc.
  • Page 52 High Quality Machines and Tools Woodstock International, Inc. carries thousands of products designed to meet the needs of today’s woodworkers and metalworkers. Ask your dealer about these fine products: ® WHOLESALE ONLY Phone: (360) 734-3482 Fax: (360) 671-3053 Toll Free Fax: (800) 647-8801 P.O.

Table of Contents