Crane Barnes SGV Series Installation Manual
Submersible grinder pump
Hide thumbs
Also See for Barnes SGV Series:
- Installation manual (27 pages) ,
- Installation manual (15 pages)
Table of Contents
Advertisement
Quick Links
IMPORTANT!
Read all instructions in this manual before operating pump.
As a result of Crane Pumps & Systems, Inc., constant product improvement program,
product changes may occur. As such Crane Pumps & Systems reserves the right to
change product without prior written notifi cation.
A Crane Co. Company
420 Third Street
Piqua, Ohio 45356
Phone: (937) 778-8947
Fax: (937) 773-7157
www.cranepumps.com
Manual Index
INSTALLATION MANUAL
Submersible Grinder Pump
Series: SGV
3, 5, 7.5HP, 60Hz,
3450RPM
1.7, 2.8, 4.2HP, 50Hz,
2850RPM
83 West Drive, Bramton
Ontario, Canada L6T 2J6
Phone: (905) 457-6223
Fax: (905) 457-2650
Form No. 113317-Rev. Z
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Crane Barnes SGV Series
Summary of Contents for Crane Barnes SGV Series
- Page 1 Read all instructions in this manual before operating pump. As a result of Crane Pumps & Systems, Inc., constant product improvement program, product changes may occur. As such Crane Pumps & Systems reserves the right to change product without prior written notifi cation.
-
Page 2: Safety First
Other brand and product names are trademarks or registered trademarks of their respective holders. ® Barnes is a registered trademark of Crane Pumps & Systems, Inc. 2001, 2002, 2003, 7/2004, 11/2004, 7/05, 8/05, 11/05, 1/06, 6/06, 9/06 , 11/06... - Page 3 USER GUIDE USER GUIDE The grinder pump generates suffi cient Congratulations on your purchase of a Barnes pressure to pump this slurry from your home to UltraGRIND™ grinder pump system. With the wastewater plant. proper care and by following a few simple guidelines your grinder pump will give you Power Failure many years of dependable service.
-
Page 4: Pump Specifications
PUMP SPECIFICATIONS: DISCHARGE ....... 2” NPT, Vertical SPEED ........ 3450 RPM, 60Hz (nominal) LIQUID TEMPERATURE ..104°F (40°C) Continuous UPPER BEARING: MOTOR HOUSING ..... Cast Iron ASTM A-48, Class 30 Design ..... Single Row, Ball, Oil Lubricated VOLUTE ......Cast Iron ASTM A-48, Class 30 Load .... - Page 5 MODEL PUMP VOLT/ NEMA FULL LOCKED CORD CODE CORD WINDING WEIGHT (Nom) START LOAD ROTOR SIZE TYPE O.D. RESISTANCE lbs. (kg) CODE AMPS AMPS ± .02 (.5) MAIN-START in (mm) Emerson Franklin SGV3072L 198 (89.8) 200/240/1 3450 25.2/21.7 86/75 10/4 0.75 (19) 0.52-4.49 2.88-4.36 SGV3062L 198 (89.8)
-
Page 6: Installation
For the location of the nearest Barnes Service Center, check province and local electric codes. It is recommended that your Barnes representative or Crane Pumps & Systems, Inc., a junction box, be mounted outside the sump or be of at... - Page 7 SERVICE: In the event of an overtemperature, the source of this condition should be determined and rectifi ed immediately. Thermal protection shall not be used as a motor overload Lubrication: device. A separate motor overload device must be provided Anytime the pump is removed from operation, the cooling in accordance with NEC codes.
- Page 8 TABLE 1 - COOLING OIL - Dielectric SUPPLIER GRADE Enerpar SE100 Conoco Pale Paraffi n 22 Mobile D.T.E. Oil Light G & G Oil Circulating 22 Imperial Oil Voltesso-35 Shell Canada Transformer-10 Texaco Diala-Oil-AX Woco Premium 100 Pressure Test: Pumps that have been disassembled, Motor Housing - If the pump has been disassembled, the oil should be drained before a pressure test, as described in section “Checking Oil”.
- Page 9 SGV5002L & SGV5022L ONLY CONTROL (Small Cable) Temperature Sensor CONTROL (Small Cable) Moisture & Temperature Sensors...
- Page 10 ALL EXCEPT SGV5002L & SGV5022L...
-
Page 12: Troubleshooting
TROUBLE SHOOTING CAUTION ! Always disconnect the pump from the electrical power source before handling. If the system fails to operate properly, carefully read instructions and perform maintenance recommendations. If operating problems persist, the following chart may be of assistance in identifying and correcting them: MATCH “CAUSE”... - Page 13 MODEL: PART NO. MODEL: PART NO. MODEL: PART NO. SGV3072L 111608 SGV5002L 115657 SGV7532L 111613 SGV3062L 111612 SGV5022L 115658 SGV7542L 111614 SGV3032L 111609 SGV5062L 111619 SGV7552L 111615 SGV3042L 111610 SGV5032L 111616 SGV3052L 111611 SGV5042L 111617 SGV5052L 111618 ALL OTHER MODELS SGV5002L &...
-
Page 14: Parts Kits
PARTS KITS Seal Repair Kit, All Except 5Hp, 1Ph ..P/N: 085223 Item #’s 5,8,14,16D,29,34,35,40 Seal Repair Kit, For 5Hp, 1Ph Only ..P/N: 118042 Item #’s 5,8,14,15D,16D,29,34,35,40 Overhaul Kit, All Except 5Hp, 1Ph ..P/N: 115771 Item #’s 2,3,5,7,8,9,14,16d,19,22,29,34,35,40 Overhaul Kit, For 5Hp, 1Ph Only .... - Page 15 MOVEABLE ASSEMBLY ITEM PART NO. DESCRITION P/N: 116728* PARTS LIST Cord & Plate Assemby for ALL Other Models For 3, 5, & 7.5HP SGV Grinders, “C” Channel Basin Package 067564 Square Ring 1-147-1 Screw 7/16-14 x 1.50” SS ITEM PART NO DESCRITION 1-319-1 Screw 7/16-14 x 2”...
- Page 17 Crane Pumps & Systems, Inc. Distributor. RETURNED GOODS RETURN OF MERCHANDISE REQUIRES A “RETURNED GOODS AUTHORIZATION”. CONTACT YOUR LOCAL CRANE PUMPS & SYSTEMS, INC. DISTRIBUTOR. Products Returned Must Be Cleaned, Sanitized, Or Decontaminated As Necessary Prior To Shipment, To Insure That Employees Will Not Be Exposed To Health Hazards In Handling Said Material.
- Page 18 A Crane Co. Company START-UP REPORT General Information Pump Owner’s Name: __________________________________________________________ Address: ____________________________________________________________________ Location of Installation: _________________________________________________________ Contact Person: __________________________________Phone: _______________________ Purchased From: _____________________________________________________________ Nameplate Data Pump Model #: ___________________ Serial #: _____________________________________ Part #: __________________________ Impeller Diameter: ____________________________ Voltage: _________ Phase: _____ Ø...
- Page 20 Notes...
Need help?
Do you have a question about the Barnes SGV Series and is the answer not in the manual?
Questions and answers