Crane Barnes SGV Series Installation Manual
Submersible grinder pump
Hide thumbs
Also See for Barnes SGV Series:
- Installation manual (27 pages) ,
- Installation manual (20 pages)
Table of Contents
Advertisement
Quick Links
IMPORTANT!
Read all instructions in this manual before operating pump.
As a result of Crane Pumps & Systems, Inc., constant product improvement program,
product changes may occur. As such Crane Pumps & Systems reserves the right to
change product without prior written notification.
A Crane Co. Company
420 Third Street
Piqua, Ohio 45356
Phone: (937) 778-8947
Fax: (937) 773-7157
www.cranepumps.com
BARNES
BARNES
INSTALLATION MANUAL
Submersible Grinder Pump
®
Series: SGV
2HP, 3450RPM
SUPERSEDED
Some parts may NOT
be available
83 West Drive, Bramton
Ontario, Canada L6T 2J6
Phone: (905) 457-6223
Fax: (905) 457-2650
Form No. 108092-Rev. H
Advertisement
Table of Contents
Related Manuals for Crane Barnes SGV Series
Summary of Contents for Crane Barnes SGV Series
- Page 1 Read all instructions in this manual before operating pump. As a result of Crane Pumps & Systems, Inc., constant product improvement program, product changes may occur. As such Crane Pumps & Systems reserves the right to change product without prior written notification. A Crane Co. Company...
-
Page 2: Safety First
Other brand and product names are trademarks or registered trademarks of their respective holders. ® Barnes is a registered trademark of Crane Pumps & Systems, Inc 2000, 2001, 1/2006 , 4/06 Alteration Rights Reserved... - Page 3 USER GUIDE USER GUIDE The grinder pump generates sufficient Congratulations on your purchase of a Barnes pressure to pump this slurry from your home to UltraGRIND™ grinder pump system. With the wastewater plant. proper care and by following a few simple guidelines your grinder pump will give you Power Failure many years of dependable service.
-
Page 4: Pump Specifications
PUMP SPECIFICATIONS: DISCHARGE ....... 1¼” NPT, Vertical UPPER BEARING: LIQUID TEMPERATURE ..160°F (71°C) Intermittent Design ..... Single Row, Ball, Oil Lubricated MOTOR HOUSING ..... Cast Iron ASTM A-48, Class 30 Load ....Radial VOLUTE ......Cast Iron ASTM A-48, Class 30 INTERMEDIATE BEARING: SEAL PLATE ...... - Page 5 MODEL VOLT PH/Hz NEMA FULL LOCKED CORD CODE CORD WINDING (Nom) START LOAD ROTOR SIZE TYPE O.D. RESISTANCE CODE AMPS AMPS ± .02 (.5) MAIN -- START in (mm) SGV2002L 1 / 60 3450 17.0 53.0 12/4 .67 (17) 0.9 -- 7.2 SGV2022L 1 / 60 3450...
-
Page 6: Service Centers
For the location of the nearest Barnes Service Center, Code and all applicable state, province and local electric check your Barnes representative or Crane Pumps codes. It is recommended that a junction box, be mounted & Systems, Inc., Service Department in Piqua, Ohio,... - Page 7 Wire Size - If additional cable is required consult a In the event of an overtemperature, the source of this condition should be determined and rectified immediately. qualified electrician for proper wire size. Thermal protection shall not be used as a motor overload device.
- Page 8 MOVEABLE ASSEMBLY For “C” Channel Basin Package PARTS LIST For 2HP SGV Grinder 107359* ITEM QTY. PART No. DESCRIPTION ITEM QTY. PART No. DESCRIPTION 107471 Lower Pump Bracket 074535 Moveable Fitting 075589 Pipe, 1.25 NPT x 14” Lg ---- Loctite PST #567 110808 U-Bolt and Nuts ----...
-
Page 11: Troubleshooting
TROUBLE SHOOTING CAUTION ! Always disconnect the pump from the electrical power source before handling. If the system fails to operate properly, carefully read instructions and perform maintenance recommendations. If operating problems persist, the following chart may be of assistance in identifying and correcting them: MATCH “CAUSE”... -
Page 13: Parts Kits
PARTS KITS Seal Repair Kit ...P/N: 110475 Overhaul Kit ....P/N: 110476 Cutter Kit ....P/N: 085226 PARTS LIST ITEM PART NO. DESCRITION ITEM QTY. PART NO. DESCRIPTION 067561 Volute 105111A Ground Wire Assy, 10GA. 067557 Seal Plate 103586 Terminal Block 087119BD Intermediate Coupling 1 or 2... -
Page 14: Returned Goods
Crane Pumps & Systems, Inc. Distributor. RETURNED GOODS RETURN OF MERCHANDISE REQUIRES A “RETURNED GOODS AUTHORIZATION”. CONTACT YOUR LOCAL CRANE PUMPS & SYSTEMS, INC. DISTRIBUTOR. Products Returned Must Be Cleaned, Sanitized, Or Decontaminated As Necessary Prior To Shipment, To Insure That Employees Will Not Be Exposed To Health Hazards In Handling Said Material.
Need help?
Do you have a question about the Barnes SGV Series and is the answer not in the manual?
Questions and answers