Table of Contents
Advertisement
Command number 230: Assignment of Zone No. to Entry No.3 of Expander module
No. 2
Default values ------------------------------------------------------------------------------> 0
Positions -------------------------------------------------------------------------------------> (1)
Command number 231: Assignment of Zone No. to Entry No.4 of Expander module
No. 2
Default values ------------------------------------------------------------------------------> 0
Positions -------------------------------------------------------------------------------------> (1)
Command number 232: Assignment of Zone No. to Entry No. 5 of Expander module
No. 2
Default values ------------------------------------------------------------------------------> 0
Positions -------------------------------------------------------------------------------------> (1)
Command number 233: Assignment of Zone No. to Entry No. 6 of Expander module
No. 2
Default values ------------------------------------------------------------------------------> 0
Positions -------------------------------------------------------------------------------------> (1)
Command number 234: Assignment of Zone No. to Entry No. 7 of Expander module
No. 2
Default values ------------------------------------------------------------------------------> 0
Positions -------------------------------------------------------------------------------------> (1)
Command number 235: Assignment of Zone No. to Entry No. 8 of Expander module
No. 2
Default values ------------------------------------------------------------------------------> 0
Positions -------------------------------------------------------------------------------------> (1)
Command number 236: Assignment of Zone No. to Entry No.1 of Expander mo-
dule No. 3
Default values -----------------------------------------------------------------------------> 0
Positions -------------------------------------------------------------------------------------> (1)
Digit position (1)-(2): Assignment of Zone No. to Entry No. 1 of Expander module No. 3
The code must have 2 digits. Valid values are 00 to 32.
Note: With value [00], the zone is cancelled.
Note: Commands 237 to 243 (Assignment of Zone No. to Entry No.1 of Expander
module No. 3) are programmed as Command No. 236.
Command number 237: Assignment of Zone No. to Entry No. 2 of Expander module
No. 3
Default values ------------------------------------------------------------------------------> 0
Positions -------------------------------------------------------------------------------------> (1)
Command number 238: Assignment of Zone No. to Entry No. 3 of Expander module
No. 3
Default values ------------------------------------------------------------------------------> 0
Positions -------------------------------------------------------------------------------------> (1)
Command number 239: Assignment of Zone No. to Entry No. 4 of Expander module
No. 3
Default values ------------------------------------------------------------------------------> 0
Positions -------------------------------------------------------------------------------------> (1)
Command number 240: Assignment of Zone No. to Entry No. 5 of Expander module
No. 3
Default values ------------------------------------------------------------------------------> 0
Positions -------------------------------------------------------------------------------------> (1)
0
2
3
0
(2)
0
2
3
1
(2)
0
2
3
2
(2)
0
2
3
3
(2)
0
2
3
4
(2)
0
2
3
5
(2)
0
2
3
6
(2)
0
2
3
7
(2)
0
2
3
8
(2)
0
2
3
9
(2)
0
2
4
0
(2)
Command number 241: Assignment of Zone No. to Entry No. 6 of Expander module
No. 3
Default values ------------------------------------------------------------------------------> 0
Positions -------------------------------------------------------------------------------------> (1)
Command number 242: Assignment of Zone No. to Entry No. 7 of Expander module
No. 3
Default values ------------------------------------------------------------------------------> 0
Positions -------------------------------------------------------------------------------------> (1)
Command number 243: Assignment of Zone No. to Entry No. 8 of Expander module
No. 3
Default values ------------------------------------------------------------------------------> 0
Positions -------------------------------------------------------------------------------------> (1)
Command number 244: Auxiliary trouble counter
Default values ------------------------------------------------------------------------------> 0
Positions -------------------------------------------------------------------------------------> (1)
Digit position (1)- (2): Auxiliary trouble counter.
The code must have 2 digits. Valid values are from 00 to 16 events.
Note: If you program 00, the equipment will not supervise the trouble.
Command number 245: Auxiliary trouble counter BUS-D485
Default values ------------------------------------------------------------------------------> 0
Positions -------------------------------------------------------------------------------------> (1)
Digit position (1)- (2):: Auxiliary trouble counter BUS-D485
The code must have 2 digits. Valid values are from 00 to 16.
Note: If you program 00, the equipment will not supervise the trouble.
Command number 246: Battery trouble counter
Default values -----------------------------------------------------------------------------> 0
Positions -------------------------------------------------------------------------------------> (1)
Digit position (1)- (2): Battery trouble counter
The code must have 2 digits. Valid values are from 00 to 16 events.
Note: If you program 00, the equipment will not supervise the trouble.
Command number 247: Siren trouble counter
Default values -----------------------------------------------------------------------------> 0
Positions -------------------------------------------------------------------------------------> (1)
Digit position (1)- (2): Siren trouble counter
The code must have 2 digits. Valid values are from 00 to 16 events.
Note: If you program 00, the equipment will not supervise the trouble.
Command number 249: Expander modules failure counter
Default values ------------------------------------------------------------------------------> 0
Positions -------------------------------------------------------------------------------------> (1)
Digit position (1)- (2): Expander modules failure counter
The code must have 2 digits. Valid values are from 00 to 16 events.
Note: If you program 00, the equipment will not supervise the troubles.
Command number 250: Auxiliary source trouble counter (Supervision, network
and low battery trouble)
Default values -----------------------------------------------------------------------------> 0
Positions --------------------------------------------------------------------------------------> (1)
Digit position (1)- (2): Auxiliary source trouble counter
The code must have 2 digits. Valid values are from 00 to 16 events.
Note: If you program 00, the equipment will not supervise the troubles.
Note: The programmed value is valid for Supervision, network and low battery
troubles.
0
2
4
1
(2)
0
2
4
2
(2)
0
2
4
3
(2)
8
2
4
4
(2)
8
2
4
5
(2)
8
2
4
6
(2)
8
2
4
7
(2)
8
2
4
9
(2)
8
2
5
0
(2)
25
Advertisement
Table of Contents
