Table of Contents
Advertisement
6.1 How to pair a wireless sensor
To pair a sensor you shall follow the steps below:
1) Make sure you remove the battery from the sensor.
2) Press the key [
] in the keypad.
3) Select the option [7] RF device.
4) Enter the installer code.
5) Choose the option [1] Sensor rec.
6) Indicate the memory position in which you wish to record the device.
Available memory positions are 01-24.
7) The keypad will indicate that it is searching the sensor.
8) Put the battery on the sensor. Please verify polarity.
9) Wait until the keypad confirms that the sensor has been properly recorded and
then press the key [
].
10) If you wish to continue recording more sensors, repeat the steps above from point
6 onwards.
On the contrary, press the key [#] to quit sensor programming.
6.2 How to pair wireless keychains
To pair a wireless keychain you shall follow the steps below:
1) Press the key [
] in the keypad.
2) Select the option [7] RF device.
3) Enter the installer code.
4) Choose the option [2] Keychain rec.
5) Indicate the memory position in which you wish to record the keychain.
Available memory positions are 01-64.
6) Hold down the keychain key and wait until the keypad confirms the recording.
Then press the key [
] in the keypad.
7) If you wish to continue recording more keychains, repeat the steps above from
point 5 onwards.
If you wish to quit keychain recording, press the key [
6.3 How to remove wireless sensors
To remove a wireless sensor you shall follow the steps below:
1) Press the key [
] in the keypad.
2) Select the option [7] RF device.
3) Enter the installer code.
4) Choose the option [3] Remove sensor.
5) Indicate the memory position of the sensor you wish to remove.
6) Confirm that you really wish to remove such sensor by pressing the key [1].
7) Press the key [
] to accept the confirmation that the sensor has been removed.
8) If you wish to continue removing sensors, repeat the steps above from point 5
onwards.
On the contrary, press the key [#] to quit this option.
6.4 How to remove wireless keychains
To remove a keychain you shall follow the steps below:
1) Press the key [program] in the keypad.
2) Select the option [7] RF device.
3) Enter the installer code.
4) Choose the option [4] Remove keychain.
5) Indicate the memory position of the sensor you wish to remove.
6) Confirm that you really wish to remove such sensor by pressing the key [1].
7) Press the key [
] to accept the confirmation that the sensor has been removed.
8) If you wish to continue removing sensors, repeat the steps above from point 5
onwards.
On the contrary, press the key [#] to quit this option.
6.5 How to verify the correct operation of a wireless sensor
To verify the correct operation of a wireless sensor, the panel has a function to assess
the RSSI transmitted by the sensor. Thus, you may know the signal level of each
wireless sensor enabled in your installation.
To assess the signal strength of wireless sensors you shall follow the steps below:
1) Press the key [program] in the keypad.
2) Select the option [7] RF device.
3) Enter the installer code.
4) Choose the option [5] Sensor test.
Every time a sensor generates a transmission, the keypad will indicate the zone of
operation of the sensor, the memory position in which it is recorded and the signal
level.
12
6.6 How to view the zones allocated to each sensor
To view the zones of operation of the different wireless sensors you shall follow the
steps below:
1) Press the key [program] in the keypad.
2) Select the option [7] RF device.
3) Enter the installer code.
4) Choose the option [6] Zone assign.
The keypad will indicate the memory position in which the sensor is recorded and the
zone of operation assigned. To switch to another sensor use the arrow keys [
6.7 How to remove all sensors and/or keychains
To remove all sensors or keychains from your system in a single step you shall
follow the steps below:
1) Press the key [program] in the keypad.
2) Select the option [7] RF device.
3) Enter the installer code.
4) Choose the option [7] Remove all.
5) Choose to remove all sensors by pressing the key [1] or choose to remove all
keychains by pressing the key [2].
6) Confirm that you really wish to remove the selected devices by pressing the key
[1] and wait until the keypad indicates that deletion is complete. Press the key [
to return to the RF device menu.
6.8 How to pair a PGM-W /MA-220G module
1) Make sure that the PGM-W is disconnected from 12V power supply.
2) Press the key [
3) Select the option [7] RF device.
4) Enter the installer code.
5) Choose the option [8] PGM-W record.
6) Indicate the PGM-W number you wish to record (use the arrow keys [
].
select the desired PGM-W number). Available PGM-Ws are from 1 to 4.
7) The keypad will indicate that it is searching the device.
8) Electrify the PGM-W module, then press the button "PAIR" located in the upper
left corner of the module.
9) Wait until the keypad confirms that the PGM-W has been properly recorded and
then press the key [#].
10) If you wish to continue recording other PGM-W modules, repeat the steps
above from point 6 onwards. On the contrary, press the key [#] to quit this option.
6.9 How to remove PGM-/MA-220G modules.
1) Press the key [
2) Select the option [7] RF device.
3) Enter the installer code.
4) Choose the option [9] Remove PGM-W.
5) Indicate the number of PGM-W you wish to remove (use the arrow keys [
to select the desired PGM-W number)
6) Confirm that you really wish to remove such module by pressing the key [1].
7) Press the key [
removed.
8) If you wish to continue removing modules, repeat the steps above from point 5
onwards.
SECTION 7: Programming through WiFi
7.1 Technical specifications:
WiFi:
• Transmission: Certified Wi-Fi 2.4Ghz, IEEE 802.11.
• Certificate FCC/CE-RED/IC/TELEC/KCC/SRRC/NCC
• Transmission power: 20,5 dBm.
• Wi-Fi authentication via WEP, WPA-PSK y WPA2-PSK.
• Antenna: PCB trace type.
• 1 WiFi recipient for reports to monitoring station
• Allows own and panel programming with AC4 software
• Allows own programming via App in AP mode from Garnet Programmer
• Reports with residential format.
• It may use domain names instead of IP addresses.
• Allows the remote operation of the system through smartphones using Garnet
Control App.
• Up to 20 residential users.
• Report communication using UDP.
• Supervision period via WiFi which may be configured from 1 to 99 minutes.
• Two Garnet report formats: DC1 y SDC2.
• 9 Led indicators of status and signal on the board.
] in the keypad.
] in the keypad.
] to accept the confirmation that the module has been
].
]
] to
]
Advertisement
Table of Contents
