Related Manuals for Barco POLARIZER R812319K
Summary of Contents for Barco POLARIZER R812319K
- Page 1 BARCO PROJECTION SYSTEMS Polarizer 6*00 R812319K R8123191K R821063K R8210631K R812317K R8123171K R817920K R817919K INSTALLATION MANUAL POLARIZER KIT FOR 6*00/SIM6 SERIES & HELIOS PROJECTORS Date : Rev : Art. No. : 07112001 R5976395...
- Page 2 Safety This procedure is intended for use only by qualified service technicians who have been trained and authorized by BARCO ! Hot Surface and Switch the projector to stand by and let it cool down for at least 15 minutes before Risk of starting with the procedure.
- Page 3 The type of polarisers in the illustration above are the polarisers used in the RSIM6 projectors and equiped with fixation screws (A) for OSEM (Optical Soft Edge Modulation) if necessary. To be continued on next page BARCO ——————————————————— 3 ————————————— Projection Systems...
- Page 4 Kit number 6300/6400 6500/6400i SIM6 SIM6MLA SIM6HB SIM6HB MLA SIM6LL HELIOS Polariser Red: R812319K Polariser Green: R821063K Polariser Bleu: R812317K Polariser Red: R8123191K Polariser Green: R8210631K Polariser Bleu: R8123171K Polariser Green: R817920K Polariser Bleu: R817919K BARCO ——————————————————— 4 ————————————— Projection Systems...
- Page 5 Open both lens locks by pulling them backwards. Take the lens out of the lens house. Illustrations on Removing the Lens Image 1 Motor part Fixation screws Lens lockings Image 2 To be continued on next page. BARCO ——————————————————— 5 ————————————— Projection Systems...
- Page 6 To remove the top cover, follow the next procedure: Top Cover Step Action Image Pull the 3 rubber sealing pieces. Turn out the 3 fixing screws. Take off the top cover. Illustrations on Top Cover Removal Image 1 Image 2 BARCO ——————————————————— 6 ————————————— Projection Systems...
- Page 7 Turn out the screws retaining the little plate A Remove the little plate Turn carefuly the remaining screws out , be aware not to drop these screws into the projector. Remove the EMC plate Illustrations Image 1 Image 2 BARCO ——————————————————— 6 ————————————— Projection Systems...
- Page 8 Take out the polarizer. Insert the new polarizer. Secure this position with both screws. Reinstall the electrical connection Illustrations on Screws Blue Polarizer Replacing the Polarizer Screws Green Polarizer Screws Red Polarizer BARCO ——————————————————— 7 ————————————— Projection Systems...
- Page 9 Color Meter Tp…rr 8‚y‚…Ã €r‡r… Image 1 Attention ! Before starting the adjustment, lets warm up the projector for 15 min. Do not connect any source to the projector. To be continued on next page. BARCO ——————————————————— 8 ————————————— Projection Systems...
- Page 10 X= red, Y= green, Z= blue Illustrations Guide tool Adjustment tool How to put the tools on the polarizer How to put the tools on the polarizer when in the projector. BARCO ——————————————————— 9 ————————————— Projection Systems...
- Page 11 Turn in the indicated screws. Put the little plate A back on its place and fix it with the 2 screws Fix the cable B with its screw Turn the remaining screws in, Illustrations Image 1 Image 2 BARCO ——————————————————— 10 ————————————— Projection Systems...
- Page 12 Put the top cover on the projector Turn in the 3 fixing screws. Cover the fixing screws with the rubber sealing pieces. Illustrations on Top Cover installation Image 1 Image 2 To be continued on next page. BARCO ——————————————————— 19 ————————————— Projection Systems...
- Page 13 If not, turn the lens a little. While pushing down, tighten wing bolts (B) firmly to ensure good functioning of safety latches and motorization. Reinstall the lens cover. Illustrations on mounting the Lens Image 1 Image 2 BARCO ——————————————————— 20 ————————————— Projection Systems...
Need help?
Do you have a question about the POLARIZER R812319K and is the answer not in the manual?
Questions and answers