Advertisement
Quick Links
Dimming & Switching Ready Retrofit Subplate
lu tro n. co m
HW R- PN LS -8
S- 12 0F T- CG
P2 73 0
P/N : HW R-S
UB PL T-0 01
Inp ut |
Ent ree | Ent
rad a
:
20 A 120
V~ 50/6 0
Hz
Ind.
243C
Cont . Eq.
LIST ED
CA UT ION
| PR EC AU
CIÓ N | AT
TE NT ION
Do not pla
ce HW -RP
or HW -RP
M- 4U -12 0
M- 4A- 120
in this loc
mo dul es
atio n
4 U
No col oqu
e HW -RP M-
o HW -RP M-
4U -12 0
4A- 120 mó
en est a ubi
dul os
cac ión
Ne pla cez
pas HW -RP
ou HW -RP
M- 4U -12 0
4 A
M- 4A- 120
dan s ce lieu
mo dul es
CA UT ION
| PR EC AU
CIÓ N | AT
TE NT ION
Do not pla
ce HW -RP
or HW -RP
M- 4U -12 0
M- 4A- 120
in this loc
mo dul es
atio n
4 U
No col oqu
e HW -RP M-
o HW -RP M-
4U -12 0
4A- 120 mó
en est a ubi
dul os
cac ión
Ne pla cez
pas HW -RP
ou HW -RP
M- 4U -12 0
4 A
M- 4A- 120
dan s ce lieu
mo dul es
CA UT ION
| PR EC AU
CIÓ N | AT
TE NT ION
Do not pla
ce HW -RP
mo dul es in
M- 4A- 120
this loc atio
n
No col oqu
e HW -RP M-
mó dul os en
4A- 120
4 A
est a ubi cac
ión
Ne pla cez
pas HW -RP
M- 4A- 120
mo dul es dan
s ce lieu
CA UT ION
| PR EC AU
CIÓ N | AT
TE NT ION
Do not pla
ce HW -RP
mo dul es in
M- 4A- 120
this loc atio
n
No col oqu
e HW -RP M-
mó dul os en
4A- 120
4 A
est a ubi cac
ión
Ne pla cez
pas HW -RP
mo dul es dan
M- 4A- 120
s ce lieu
Overview
Use this guide to successfully install a Dimming and Switching Subplate into a UL Listed enclosure provided by
others. This guide describes subplate installation, wiring, and load activation.
CA UT ION
| PR EC AU
CIÓ N | AT
TE NT ION
Do not pla
ce HW -RP
or HW -RP
M- 4U -12 0
M- 4A- 120
in this loc
mo dul es
atio n
4 U
No col oqu
e HW -RP M-
o HW -RP M-
4U -12 0
4A- 120 mó
en est a ubi
dul os
cac ión
Ne pla cez
pas HW -RP
ou HW -RP
M- 4U -12 0
4 A
M- 4A- 120
mo dul es
dan s ce lieu
CA UT ION
| PR EC AU
CIÓ N | AT
TE NT ION
Do not pla
ce HW -RP
or HW -RP
M- 4U -12 0
M- 4A- 120
in this loc
mo dul es
atio n
4 U
No col oqu
e HW -RP M-
o HW -RP M-
4U -12 0
4A- 120 mó
en est a ubi
dul os
cac ión
Ne pla cez
pas HW -RP
ou HW -RP
M- 4U -12 0
4 A
M- 4A- 120
mo dul es
dan s ce lieu
CA UT ION
| PR EC AU
CIÓ N | AT
TE NT ION
Do not pla
ce HW -RP
mo dul es in
M- 4A- 120
this loc atio
n
No col oqu
e HW -RP M-
mó dul os en
4A- 120
4 A
est a ubi cac
ión
Ne pla cez
pas HW -RP
mo dul es dan
M- 4A- 120
s ce lieu
CA UT ION
| PR EC AU
CIÓ N | AT
TE NT ION
Do not pla
ce HW -RP
mo dul es in
M- 4A- 120
this loc atio
n
No col oqu
e HW -RP M-
mó dul os en
4A- 120
4 A
est a ubi cac
ión
Ne pla cez
pas HW -RP
mo dul es dan
M- 4A- 120
s ce lieu
WA RNI NG |
ADV ERT ENC
AVE RTI SSE
IA |
ME NT
Tec h:
1. Be sure to
read Instr uctio
2. Do not block
n Shee t.
Tes ter:
vents . 35 cm
1. Aseg úrese
clear ance requ
de leer la Hoja
ired.
2. No obstr uya
de Instr uccio
QA:
los respi rader
nes.
cm libres .
os. Se requ
ieren 35
1.
Seri al #:
2. Ne pas obstr
uer les éven
de 35 cm est
ts. Un déga
Job #:
néce ssair e.
geme nt
Date Cod e:
Installation Guide
Contents
Subplate Model Number Guide
CGP2730 Subplate
Compatible Enclosure Dimensions
Enclosure Preparation
Enclosure Label Installation
S
u
b
p
a l
e t
M
o
u
n
n i t
g
Module and Module Interface Installation
Module Specific Installation Wiring
System Wiring Overview
Module Specific Load Wiring
PELV (Class 2: USA) Wiring
Temporary Lighting
Activate Loads in Bypass
Complete Installation
Included Front Cover
Warranty and Contact Information
®
CGP2730
Please Read
2
3
4
5
6-7
8-10
11
12-13
14
15
16
17
18
20
Advertisement
Subscribe to Our Youtube Channel
Related Manuals for Lutron Electronics CGP2730
Summary of Contents for Lutron Electronics CGP2730
- Page 1 Ne pla cez pas HW -RP ou HW -RP M- 4U -12 0 CGP2730 Subplate M- 4A- 120 dan s ce lieu mo dul es Compatible Enclosure Dimensions Enclosure Preparation CA UT ION | PR EC AU CIÓ...
- Page 2 16 A total per module (1 circuit/module), 5 A per output (1/4 HP motor, 1 per output), 4 outputs per module 4FSQ 8 A total per module (1 circuit/module), 2 A per output (single ceiling fan), 4 outputs per module Installation Guide for CGP2730 Dimming and Switching Subplate ®...
- Page 3 37 in (939.8 mm) (Sidewall) Existing UL Label Do not remove the existing UL label, this will be needed to confirm UL compliance of the enclosure. Front View Side View Installation Guide for CGP2730 Dimming and Switching Subplate 3 ® ®...
- Page 4 Compatible Enclosure Labeling Enclosure Label Installation This page describes how and where to install the labels provided by Lutron. These labels contain torque and wiring information in addition to bypass jumper placement. Enclosure and Subplate Guidelines • For indoor use only with NEMA/UL Type 1 listed enclosure, IP20. •...
- Page 5 Torque the screws Drill holes using a #29 bit and vacuum to 17 in-lbs (1.92 N • out any metal shavings. Installation Guide for CGP2730 Dimming and Switching Subplate 5 ® ®...
- Page 6 Module and Module Interface (MI) Installation Module installation: Secure up to 8 modules using three screws for each module. Place the tab on the bottom of the module around the single screw and pull up. This will align the top two screws.
- Page 7 Vor dem Siche rungs l, schal ten autom aten Sie bitte und siche und Haup alle rn diese tscha lter in der AUS- Posit ion. HWI-MI-120 Power Wiring: Installation Guide for CGP2730 Dimming and Switching Subplate 7 ® ®...
- Page 8 Module Specific Installation Wiring • Use the following information to wire the newly installed modules. • Terminal blocks for 4U, 4J, and 4FSQ modules come pre-installed on the subplate. • Terminal blocks for 4M and 4R modules are included with the modules and should be installed in place of the default terminal blocks as needed.
- Page 9 Secure wire bundles with zip-ties, neatly out of the way of anything that can damage the wires. Switching Module (4R) 4-Circuit BLACK WIRES RED WIRES WHITE WIRE Terminal Blocks Installation Guide for CGP2730 Dimming and Switching Subplate 9 ® ®...
- Page 10 Module Specific Installation Wiring (continued) • Use the following information to wire the newly installed modules. • Terminal blocks for 4U, 4J, and 4FSQ modules come pre-installed on the subplate. • Terminal blocks for 4M and 4R modules are included with the modules and should be installed in place of the default terminal blocks as needed.
- Page 11 DO NOT TIE NEUTRAL • Run wiring so that line (mains) voltage wiring will be at least 6 ft (1.83 m) from sound or electronic equipment and its wiring. BUSSES TOGETHER Installation Guide for CGP2730 Dimming and Switching Subplate 11 ® ®...
- Page 12 Module Specific Load Wiring Load Circuit Wiring: 4U/4J/4FSQ (single typical dimming/switching leg shown for each module type) • Connect Hot load wiring to the appropriate load terminal set for each circuit and Neutral to the Neutral bus. • The Dimmed Hot (DH) and/or Switched Hot (SH) terminal blocks are grouped by a module (4 output circuits each) in numbered order in the top right of the subplate.
- Page 13 4-Circuit Switching Module (4R) Circuit breaker Neutral Switched hot/live Neutral Neutral Load Terminals Shade Neutral Lower Raise Feed Neutral 4-Output Motor Module (4M) Circuit breaker Hot/Live Neutral Load Neutral Terminals Installation Guide for CGP2730 Dimming and Switching Subplate 13 ® ®...
- Page 14 PELV (Class 2: USA) Wiring CGP2730 MI Wiring: Terminate the processor communication link on the last module interface. If any of the module interfaces are located more than 50 ft (15.25 m) from the processor, the last module interface on the chain must utilize a terminator across terminals 3 and 4.
- Page 15 Bypass jumpers come pre-installed in the module terminal blocks for your convenience and will allow for temporary lighting until your system is programmed. Installation Guide for CGP2730 Dimming and Switching Subplate 15 ® ®...
- Page 16 Activate Loads in Bypass A. Complete load wiring. B. Check that the bypass jumpers are in place. These jumpers protect from load faults and must be used to check load wiring when it is installed or modified. WARNING! Shock hazard. May result in serious injury or death if panel is not wired correctly.
- Page 17 Module with 4 outputs shown Notice: Reuse the bypass jumpers whenever work is being done on a load. Damage caused by short-circuits and mis-wiring is not covered by the product warranty. Installation Guide for CGP2730 Dimming and Switching Subplate 17 ® ®...
- Page 18 Included Front Cover HWR-COVER-001 CGP2730 subplate dimming/switching solutions are designed to only work inside compatible LiteTouch or Savant enclosures with corresponding Lutron provided front cover part #HWR-COVER-001. This front cover is specifically designed to provide proper convection cooling while safely preventing access to line voltage sections of the panel.
- Page 19 Notes Installation Guide for CGP2730 Dimming and Switching Subplate 19 ® ®...
- Page 20 Fax +1.610.282.1243 http://www.lutron.com http://forums.lutron.com Lutron, , Hi-lume, Eco-10 and HomeWorks are registered trademarks of Lutron Electronics Co., Inc. Savant and LiteTouch are registered trademark of Savant. © 2015 Lutron Electronics Co., Inc Lutron Electronics Co., Inc. Made and printed in U.S.A. 07/2015 ®...
Need help?
Do you have a question about the CGP2730 and is the answer not in the manual?
Questions and answers