Operation; Troubleshooting; Changing The Batteries; Care And Cleaning - Renkforce 1519480 Operating Instructions Manual

Siero solar exterior wall lamp with motion detector

Hide thumbs

Table of Contents

Available languages

Operation

On/off

Approx. 100º

Changing the batteries

If there is a noticeable drop in the lamp's brightness, replace the rechargeable batteries with batteries of the

same type and capacity (see "Technical data" for details).

2 x

• Before using the outdoor wall lamp, remove the base by

turning it in an clockwise direction (see diagram).

• Turn on the switch inside the housing (0 = Off, 1 = On).

• Replace the base and turn it anticlockwise to secure it in

place.

• When you have finished using the wall lamp, follow the steps

above to remove the base, and then turn off the switch.

• The twilight switch turns the lamp on and off when the

ambient brightness is lower/higher than the trigger value.

• If the IR sensor detects movement when the lamp is

switched on, the brightness automatically increases to the

maximum level.

• The brightness returns to normal if no movement is detected

for 40 seconds (± 5 seconds).

• Unscrew the two Phillips screws on the sides.

• Pull the lamp off the wall mounting clamp.

• Unscrew the base in an anticlockwise direction (see

diagram).

• Remove the two Phillips screws that secure the bulb

holder in place.

• Remove the bulb holder.

• Remove all three batteries from the battery compartment.

• Insert three identical rechargeable batteries into the

battery compartment, paying attention to the polarity

markings (plus/+ and minus/-).

• Place the bulb holder back into the lamp.

• Tighten the two Phillips screws to secure the bulb holder

in place.

• Replace the base and turn it clockwise to secure it in

place (see diagram).

• Slide the lamp back onto the wall mounting clamp. Ensure

that the screw holes are aligned correctly.

• Replace the two Phillips screws on the side of the lamp.

Troubleshooting

Problem

Possible cause

The lamp does not

The lamp is switched off.

work after it has

been charged for

two days.

Insufficient sunlight.

The lamp is mounted in an

unfavourable location.

The solar cell is dirty.

Is the twilight switch

working?

Care and cleaning

• This product does not require maintenance apart from changing the rechargeable batteries.

• Never point a garden hose or pressure washer at the product (e.g. for cleaning).

• Before cleaning the lamp, turn it off and remove the batteries.

• Keep the four drainage holes on the inside of the housing (remove the outer wall light lower part first) and

the PIR sensor from dust and other dirt.

• Never use aggressive detergents, rubbing alcohol or other chemical solutions, as these could damage the

casing or cause the product to malfunction.

• Use a damp, lint-free cloth to clean the outside of the housing.

Disposal

a) Product

Electronic devices are recyclable waste and must not be disposed of in household waste.

Always dispose of the product according to the relevant statutory regulations.

Remove any inserted rechargeable batteries and dispose of them separately from the product.

b) Rechargeable batteries

As the end user, you are required by law to return all used rechargeable batteries. They must not

be placed in household waste!

Rechargeable batteries that contain hazardous substances are labelled with this symbol to

indicate that disposal in household waste is forbidden. The abbreviations for heavy metals in

batteries are: Cd = Cadmium, Hg = Mercury, Pb = Lead (indicated on rechargeable batteries,

e.g. below the trash icon on the left).

Used rechargeable batteries can be returned to local collection points, our stores or battery retailers.

You thus fulfil your statutory obligations and contribute to the protection of the environment.

Technical data

Solar panel ....................................................Polycrystalline, 4.85 V, 150 mA, 0.73 W

Rechargeable batteries .................................3 x 1.2 V AAA (Ni-MH), 900 mAh

Charging cycles .............................................min. 500

Battery life ......................................................Up to 8 hours (after full charge)

Protection rating ............................................IP44

Protection class .............................................III

Power consumption .......................................Max. 0.16 W

Material ..........................................................Stainless steel and plastic

Illuminant .......................................................4 X SMD 2835 (white), 3.2 V, 150 mA, 0.5 W

Luminous flux ................................................14 lm (twilight switch turned on)

Luminous flux ................................................70 lm (triggered by motion sensor)

Colour temperature ........................................4000 K

Installation height ...........................................Approx. 2 m

Angle of detection (sensor) ............................100 ° (horizontal), 50 ° (vertical)

Sensor range .................................................Approx. 8 m

Switch-on brightness .....................................< 50 Lux

Operating/storage conditions ......................... -20 to +40 °C, 0–100 % relative humidity (non-condensing)

Dimensions (Ø x H) .......................................10.2 x 15 cm

Weight ...........................................................Approx. 400 g

This is a publication by Conrad Electronic SE, Klaus-Conrad-Str. 1, D-92240 Hirschau (www.conrad.com).

All rights including translation reserved. Reproduction by any method (e.g. photocopy, microfilming, or the capture in

electronic data processing systems) requires prior written approval from the editor. Reprinting, also in part, is prohibited.

This publication represents the technical status at the time of printing.