Operating Elements; Maintenance And Cleaning; Technical Data; Operation - Renkforce Modica 1297726 Operating Instructions Manual

• Disconnect the power adaptor from the mains socket if you do not use the
device for an extended period of time.
• Do not leave the appliance unattended while in operation.
• Avoid using the product near strong magnetic fields such as near
machines or loudspeakers.
• Consult an expert when in doubt about operation, safety or connection of
the device.
• Maintenance, modifications and repairs are to be performed exclusively
by an expert or at a qualified repair shop.
• If you have questions which remain unanswered by these operating
instructions, contact our technical support service or other technical
personnel.

Operating elements

1
6
1 Lampshade
2 Lamp hinge with tommy screw
3 Connection socket

Operation

1. Place the lamp with the stand (4) on a dry, clean and level surface.
2. Hold the lampshade (1) with one hand. Loosen the tommy screws on the lamp
hinges (2) in an anticlockwise direction and adjust the lamp to the desired position.
The lamp can be adjusted to the desired position using the lower and upper hinges.
Tighten the tommy screws in a clockwise direction to fix the lamp hinges into
position.
3. Make sure that the lamp is turned off. Turn the rotary switch (5) anticlockwise until
it clicks into place. The light is turned off when the switch is in this position.
4. Connect the low voltage plug on the power adapter to the connection socket (3) on
the lamp cable. Insert the mains plug on the power adapter into a suitable mains
socket. The LED indicator (6) turns on.
5. Turn the rotary switch clockwise to turn on the lamp. The brightness of the LEDs
can be adjusted gradually using the rotary switch. Turning clockwise increases the
brightness. Turning anticlockwise decreases the brightness.
6. If necessary, adjust the direction of the light and the objects that are illuminated
by moving the lamp hinges.
7. After use, switch off the lamp using the rotary switch and disconnect the power
adapter from the power supply.
5 4 3
4 Stand
5 Rotary switch
6 LED indicator

Maintenance and cleaning

Never use aggressive detergents, rubbing alcohol or other chemical
solutions, as these could damage the housing or even impair the
functioning of the product.
• Turn off the lamp before cleaning and remove the mains plug from the mains. Let the
lamp cool down sufficiently.
• Clean the lamp using a clean, soft and dry cloth. Dust can be easily removed using
a clean and soft brush.
• The LED light bulbs are firmly embedded and cannot be changed.
Disposal
Electronic devices are recyclable waste and must not be disposed of in the
household waste.
At the end of its service life, dispose of the product according to the
relevant statutory regulations.
You thus fulfil your statutory obligations and contribute to the protection of the
environment.
2

Technical data

a) Lamp
Operating voltage/current .................10 V/DC, 600 mA
Protection class ..................................III
Power consumption............................8 W
LED wattage .........................................6 W
Illuminant ..............................................69 x LED (embedded, not replaceable)
Colour temperature.............................4000 K
Luminous flux .......................................400 lm (± 10%)
Operating conditions ..........................0 to +40 °C, 20 - 90 % RH
Storage conditions..............................-10 to +80 °C, 0 - 95 % RH
Dimensions (W x H) ............................645 x 330 mm when positioned at 90°
Weight ...................................................ca. 1560 g
b) Power adapter
Input voltage / current........................100-240 V/AC, 50/60 Hz, max. 0.2 A
Output voltage / current .....................10 V/DC, 600 mA
Protection class ..................................II
Cable length .........................................1.5 m
Weight ...................................................ca. 74 g
This is a publication by Conrad Electronic SE, Klaus-Conrad-Str. 1, D-92240 Hirschau (www.conrad.com).
All rights including translation reserved. Reproduction by any method, e.g. photocopy, microfilming, or the capture in electronic data
processing systems require the prior written approval by the editor. Reprinting, also in part, is prohibited. This publication represent the
technical status at the time of printing.
© Copyright 2015 by Conrad Electronic SE. V4_0715_02-HK